19
Operations
Preparing for surround sound
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level. The CLIP indicator will blink to indicate the source signal.
1Use the INPUT SELECTOR knob to select the input level of the
source you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2Press the SOUND key repeatedly until the “INPUT” indication
appears.
3Use the MULTI CONTROL keys to adjust the input level.
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4Press the SOUND key again to return to the input indication.
Preparing for playback
Normal playback
Some preparatory steps are needed before starting playback.
Turning on the receiver
1Turn on the power to the related components.
2Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) keys.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the
source name to “MD,” follow the steps below:
1Use the INPUT SELECTOR knob to select “TAPE”.
2Hold down the AUTO/CINEMA EQ. key for more than 2 seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat procedure 2.
A ON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
B ON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
A+B ON : Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listening
with headphones for stereo sound and virtual surround in all
playback modes.
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/6ch,
or VIDEO2/MONITOR jacks, make sure that the input mode setting is
correct for the type of audio signal to be used. 8
5Setup is complete when the input indication reappears.
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
4
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
1Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers: ____ feet (meters)
Distance to center speaker: ____ feet (meters)
Distance to surround speakers: ____ feet (meters)
2Use the MULTI CONTROL keys to select the distance to the
front speakers.
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3Press the SET UP key to accept the settings.
4Repeat steps 2 and 3 to input the distance for each of the
speakers.
Input the distance to the speakers.
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
SW
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
STEREO
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
STEREO
SW
AUTO/CINEMA EQ.
INPUT MODE
POWER
ON/STANDBY
INPUT SELECTOR
LFE
C
SRSLS
TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
B
Selecting the speaker system (KRF-V6050D only)
Press the SPEAKERS A or B key to select the speaker system to
be used.
LFE
C
SRSLS
TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
B
The speaker indicator lights.
KRF-V5050D
KRF-V6050D
The indicator for the speakers
you want to use should be lit.
• Selecting “6ch INPT” by pressing the INPUT MODE key, whereby
“DVD/6ch” is the input source, will cause SPEAKER A to be selected
automatically.
On the KRF-V5050D, press the SPEAKER key to switch the speak-
ers on and off.
Speakers A/B (SPEAKER/MUTE)
RDS
TP
CLIP