Manuals / Brands / Home Audio / Satellite Radio / Kenwood / Home Audio / Satellite Radio

Kenwood TH-D7A, TH-D7E SELECTING SCAN RESUME METHOD, [1], [5], [2], [UP], [OK], [DWN], [MENU], [MENU], 14 • Seek mode, 5• Time-Operatedmode, 9• Carrier-Operatedmode

1 112

Download 112 pages, 2.48 Mb

SELECTING SCAN RESUME METHOD

1The transceiver stops scanning at a frequency (or memory channel) on which a signal is detected. It then

2continues scanning according to which resume mode

3you select. You can choose one of the following modes.

4The default is Time-operated mode.

5• Time-Operated mode

6The transceiver remains on a busy frequency (or

7memory channel) for approximately 5 seconds, and then continues to scan even if the signal is still

8present.

9• Carrier-Operated mode

10

The transceiver remains on a busy frequency (or

11memory channel) until the signal drops out. There is

12a 2 second delay between signal drop-out and scan

1Press [MENU] to enter Menu mode.

2Press [1], [5], [2] to select “1–5–2 (SCAN RESUME)”.

3Press [UP]/ [DWN] to select Time-Operated (default), Carrier-Operated, or Seek.

13

resumption.

14 • Seek mode

15The transceiver remains on a busy frequency (or

4Press [OK] to complete the setting.

5Press [MENU] to exit Menu mode.

16

17

memory channel) even after the signal drops out and does not automatically resume scanning.

Note: To temporarily stop scanning and monitor weak signals, press and

18hold [MONI]. Release the key to resume scanning.

19

20

21

22

23

34

Contents

Page THANK YOU MODELS COVERED BY THIS MANUAL TH-D7A: TH-D7E: FEATURES NOTICES TO THE USER PRECAUTIONS PREPARATION FIRST QSO OPERATING BASICS GETTING ACQUAINTED CHAPTER SCAN CONTINUOUS TONE CODED SQUELCH SYSTEM (CTCSS) DUAL TONE MULTI-FREQUENCY(DTMF) FUNCTIONS VC-H1 SYSTEM® APRS® MESSAGE WIRELESS REMOTE CONTROL (TH-D7AONLY) SUPPLIED ACCESSORIES Accessory Part Number CONVENTIONS FOLLOWED IN THIS MANUAL Instruction PREPARATION Batteries VHF Band UHF Band INSTALLING THE ANTENNA INSTALLING THE HAND STRAP/ BELT HOOK INSTALLING ALKALINE BATTERIES CONNECTING WITH A REGULATED POWER SUPPLY FIRST QSO OPERATING BASICS ADJUSTING SQUELCH ■ Selecting Output Power 1ORIENTATION GETTING ACQUAINTED INDICATORS CURSOR KEYS BAND A & B 7UP/ DWN keys DWN 14OK key BASIC TRANSCEIVER MODES VFO mode Memory Recall mode [MR] Function Select mode Full Duplex mode [DUP] 10 Packet mode KEYPAD DIRECT ENTRY [4] [DUAL] MENU SET-UP MENU CONFIGURATION Level Selections Default Ref Page Page OPERATING THROUGH REPEATERS ■Selecting Offset Direction ■Selecting Offset Frequency 13■ Selecting a Tone Frequency AUTOMATIC REPEATER OFFSET U.S.A. and Canada versions REVERSE FUNCTION [REV] AUTOMATIC SIMPLEX CHECK (ASC) [REV] (1 s) [REV] TONE FREQ. ID [2] (1 s) [OK] (1 s) [1] MEMORY CHANNELS 6SIMPLEX & REPEATER OR ODD-SPLITMEMORY STORING ODD-SPLITREPEATER FREQUENCIES RECALLING A MEMORY CHANNEL [3] CLEARING A MEMORY CHANNEL 3Press [MR]+ POWER ON NAMING A MEMORY CHANNEL [A/B] [MN<->f] 9■ Recalling the Call Channel ■Reprogramming the Call Channel MEMORY-TO-VFOTRANSFER CHANNEL DISPLAY [A/B]+ POWER ON PARTIAL OR FULL RESET 1Press [F]+ POWER ON 12VHF Band Defaults Version VFO Freq SCAN SELECTING SCAN RESUME METHOD 5• Time-Operatedmode 9• Carrier-Operatedmode 14 • Seek mode VFO SCAN 2Press [VFO] (1 s) MEMORY SCAN 2Press [MR] (1 s) ■Locking Out a Memory Channel ■Setting Scan Limits ■Using Program Scan CONTINUOUS TONE CODED SQUELCH SYSTEM (CTCSS) USING CTCSS CTCSS FREQ. ID [4] (1 s) DUAL TONE MULTI-FREQUENCY(DTMF) FUNCTIONS ■TX Hold 4■ Storing a DTMF Number in Memory ■Transmitting a Stored DTMF Number MICROPHONE CONTROL AUXILIARY FUNCTIONS CHANGING FREQUENCY STEP SIZE PROGRAMMABLE VFO TONE ALERT BEEP ON/OFF ADJUSTING VOLUME BALANCE 1 Press [BAL] 17 LAMP FUNCTION [LAMP] ADJUSTING DISPLAY CONTRAST AUTOMATIC POWER OFF (APO) BATTERY SAVER POWER-ONMESSAGE TRANSCEIVER LOCK [F] (1 s) TX INHIBIT SWITCHING AM/FM MODE (TH-D7AONLY) ADVANCED INTERCEPT POINT (AIP) SWITCHING TX DEVIATION (TH-D7EONLY) PACKET OPERATION CONNECTING WITH A PERSONAL COMPUTER OPERATING TNC •Command mode [Ctrl]+[C] •Converse mode Page SELECTING DATA BAND FULL DUPLEX DX PACKETCLUSTERS MONITOR SLOW-SCANTELEVISION (SSTV) WITH VC-H1 ENTERING CALL SIGN/ MESSAGE/ RSV Readability Video Signal Strength SELECTING COLOR FOR CALL SIGN/ MESSAGE/ RSV VC-H1CONTROL AUTOMATIC PACKET/ POSITION REPORTING SYSTEM® [BCON] RECEIVING APRS DATA Indicator Meaning What is Included Selections ACCESSING RECEIVED APRS DATA 41 Press [LIST] [A/B] (1 s) Page PROGRAMMING A CALL SIGN SELECTING YOUR STATION ICON ENTERING LATITUDE/ LONGITUDE DATA [POS] 11 Press [OK] SELECTING A POSITION COMMENT ENTERING STATUS TEXT PROGRAMMING A GROUP CODE All calls: Special: Alternate net: [A] PROGRAMMING A PACKET PATH Method 1 (Specific path): Method 2 (Generic path): Method 3 (WIDEN-Npath): Method 4 (SSID path): Number of SELECTING BEACON TRANSMIT METHOD [BCON] again SELECTING BEACON TRANSMIT INTERVAL RESTRICTING RECEPTION OF APRS DATA [B] APRS® MESSAGE RECEIVING A MESSAGE New ACCESSING RECEIVED APRS MESSAGES 31 Press [MSG] [MSG] qMessage Type wRX or TX ENTERING A MESSAGE [TNC] TRANSMITTING A MESSAGE WIRELESS REMOTE CONTROL (TH-D7AONLY) 7 Press [PTT]+[MR]+ POWER ON CONTROL OPERATION KENWOOD ➡[ENT]) or ([VFO] ➡ [UP]/ [DWN]) To recall a memory channel: [TONE SEL] SKY COMMAND 2 (TH-D7AONLY) CONNECTING THE TRANSPORTER WITH THE HF [SYNC] PROGRAMMING CALL SIGNS On Commander On Transporter PROGRAMMING A TONE FREQUENCY [POWER] Key Function UP/ DWN A/B [FAST] MAINTENANCE TROUBLESHOOTING Problem Probable Cause Corrective Action Press [A/B]+ POWER ON to exit Press [BAL], then [UP]/ [DWN] to Page Ref. Page OPTIONAL ACCESSORIES PG-3J PG-4W PG-4V PG-4R EQUIPMENT CONNECTIONS SPECIFICATIONS Transmitter Receiver APPENDIX Page Page Page QUICK REFERENCE GUIDE Page INDEX