Because Whirlpool Corporation policy includes a continuous commitment to improve ourproducts, we reserve the right to change materials and specifications without notice.Dimensions are for planning purposes only. For complete details, see InstallationInstructions packed with product. Specifications subject to change without notice.Briva™Dishwasher
®

PRODUCT MODEL NUMBERS OVERALL DIMENSIONS

CABINET OPENING DIMENSIONS

DISHWASHER DRAIN

KIDS36EP KIDS42EP

Electrical: 120-volt, 60-Hz, AC-only, 15- or

20-amp. electrical supply. Use copper wire only.

A time-delay fuse or circuit breaker and separate

circuit is recommended.

If using a Hot Water Accessory Tank and/or a

garbage disposer, a separate 120-volt, 60 Hz,

AC-only, 15- or 20-amp fused electrical supply

is required for each devise.

Water:For dishwasher, a hot water line with

20-120 psi (138-827kPa) water pressure. Water

temperature must be minimum 120°F (48.9°C)

at dishwasher. Use 3/8" O.D. copper tubing with

compression fitting is recommended. Use a 90°

elbow with 3/8" N.P.T. external pipe threads on

one end to connect to water inlet valve. Do not

solder within 6" (15.2 cm) from water inlet

valve. For sink faucet, hot and cold water line.

Copper tubing with compression fitting for

specific faucet to be installed.

Drain: Separate drain P-traps for sink and

dishwasher.

Ref. 856476612-06-04
If the dishwasher drain exits
through the back wall, the
centerline of the drain must be
a minimum of 1/2" (1.3 cm)
below the dishwasher drain.
This is required to completely
drain the dishwasher tub so
that no standing water
remains in tub.
22-1/32"(56.0 cm)to bottom ofdishwasherdrain 1/2" (1.3 cm)minimumbackwall

Back right corner: If countertop is

more than 3/4" (1.9 cm) thick,

measure down 3/4" (1.9 cm) and cut

45°bevel all the way around radius.

A

IMPORTANT:Corner radius dimensions

specified must be used. If they are not,

the dishwasher will not fit the opening.

radius: 2-1/4" (5.7 cm)

C3/4" (1.9 cm)45°for base cabinetinstallations, min. 36"(91.4 cm) width required21-1/8" (53.7 cm)
(see *NOTE)
A
A
B
A
It is recommended that sinkwater and drain lineconnections be located onthis side of cabinet.It is recommendedthat dishwasher waterand drain lineconnections belocated on this sideof cabinet.C21-1/8" (53.7 cm)
(see *NOTE)
backsplash

CRITICAL

RADIUS

Bradius: 1" (2.5 cm) – the

right back corner must be

cut to this radius

25" (63.5 cm) deepcountertopCountertop must belevel.7/16" (1.1 cm) min. flat surface required
*NOTE:The cutout must be
accurately cut to the dimensions
shown within 1/16" (1.6 mm).
Dishwasher top flange overlaps
the countertop cutout by 7/16"
(1.1 cm) on front and back edges
and 1/4" (6.4 mm) on sides.
• Cabinetry and countertop must
be sturdy enough to support
loaded dishwasher and sink
(400 lbs. [181.4 kg]).
19-3/8"
(49.2 cm)
maximum
opened lid
height
20-21/32" (52.5 cm)
9-7/16"
(24.0 cm)
1-3/4" (4.4 cm)
to center of single
hole faucet
factory
installed
air gaps
dishwasher
drain
water inlet
valve
(between clamp rails)
22" (55.9 cm)
(between clamp rails)
5-25/32"
(14.7 cm)
D
14" (35.6 cm)
18-5/16" (46.5 cm)
22-1/32"
(56.0 cm)
21"
(53.3 cm)
1-1/4"
(3.2 cm)
8"
(20.3 cm)
C
center of
sink drain
5-1/2 ft. (1.7 m)
3-prong ground-type
power supply cord
B
to center of single
hole faucet
GFCI reset
buttons
SIDE FRONT
A
ABCD
42" model 40-1/2" 16-7/8" 9-9/16" 39-11/16"
(102.9 cm) (42.9 cm) (24.3 cm) (100.8 cm)
36" model 34-1/2" 10-7/8" 6-9/16" 33-11/16"
(87.6 cm) (27.5 cm) (16.6 cm) (85.6 cm)
42" model – 40" (101.6 cm)36" model – 34" (86.4 cm)
(see *NOTE)