Fill the hopper with pellets
Make sure the hopper lid is completely closed
Press the “START” button on the control panel to
begin the ignition cycle
1.
2.
3.
Open hopper lid and fill hopper with pellets
Make sure the hopper lid is completely closed
Check to make sure the stove remains lit
If the flame goes out, press the “START” button
on the control panel to re-ignite
1.
2.
3.
4.
Press the
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
“STOP” button
(The fans will automatically turn off once the stove
has cooled down)
1.
FLAME APPEARANCE
PROPERLY ADJUSTED FLAME IMPROPERLY ADJUSTED FLAME
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
3
The appearance of the flame can be a good indicator of the overall performance of the stove. A bright clean flame
indicates proper balanced and efficient burning, while a dark slow-moving flame indicates incomplete combustion
and a stove that may be in need of service and/or adjustment.
MANUAL OPERATION*
2
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
Combustion Air Trim Heat Output Button Blower Button
Once the stove is running, you
can use the heat output button
to choose between five levels
ranging from low to high.
The blower button is used to
vary the output of the room fan.
Choose between five levels rang-
ing from low to high.
Used to fine tune the amount of
combustion air to better accom-
modate variables such as venting
configuration, altitude and fuel.
Pellet Feed Trim
Used to fine tune the amount of
pellets fed into the UltraGrate™
and accommodate variations in
pellet size.
Hopper lid must
be closed during
operation.
The control board is located on the left
side of the stove.
* Refer to the Manual if you are connecting your stove to a thermostat. Ignition and control board functions for
automatic (thermostat) operation are different from the explanations given above.
SHARP ACTIVE
FLAME
BRIGHT YELLOW HUE
PELLET EMBERS
ACTIVELY MOVE IN
THE ULTRAGRATE
•
•
•
SLOW LAZY FLAME
DARK ORANGE HUE
LARGE FLAME WITH
BLACK SOOTY TIPS
PELLETS BUILD UP IN
THE ULTRAGRATE
•
•
•
•
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
STARTING THE MONTAGE™ PELLET STOVE
RE-FUELING WHILE IN OPERATION
STOPPING THE MONTAGE PELLET STOVE
START
HEAT
OUTPUT
BLOWER
FEEDING
STOP
(-) (+)
O
(-) (+)
O
COMBUSTION
AIR
PELLET
FEED
HEARTH PRODUCTS
The stove burns clean and heats efficiently. Requires more frequent maintenance and can be unsafe
to operate.
Failure to ensure that pellets in the UltraGrate™ remain burning
after re-fueling may result in smoke escaping from the unit.