LIGHTING INSTRUCTIONS – MILLIVOLT GAS VALVEFOR YOUR SAFETY READ BEFORE LIGHTINGWARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSIONMAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. This appliance has a pilot which must be lighted with a piezo

• Do not use any phone in your building.

ignitor. When lighting the pilot, follow these instructions

• Immediately call your gas supplier from a neighbor’s phone.

exactly.

• If your gas supplier cannot be reached, call the fire depart-

 

B. BEFORE OPERATING smell all around the appliance area for

ment.

 

gas. Be sure to smell next to the floor because some gas is

C. Use only your hand to push in or turn the gas control knob.

heavier than air and will settle on the floor.

 

Never use tools. If the knob will not push in or turn by hand,

WHAT TO DO IF YOU SMELL GAS

do not try to repair it, call a qualified service technician. Force

 

or attempted repair may result in a fire or an explosion.

•Extinguish any open flame.

•

Open windows.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

•

Do not light any appliance.

appliance and to replace any part of the control system and

•

Do not touch any electrical switches.

any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above on this page. 6. Wait five (5) minutes to clear out any gas. If you then smell gas,

 

 

 

 

 

 

 

STOP! Follow “B” in the safety information above on this page. If you

2.

Access the lower control compartment.

 

do not smell gas, go to the next step.

3.

Turn remote wall switch to “OFF.”

 

 

7.

Push in gas control knob slightly and turn counterclockwise

4. Verify main line shut-off valve is open.

 

to “PILOT.”

8.

Push in control knob all the way and hold in. Immediately light the

 

 

 

 

 

 

5.

Push in gas control knob slightly and turn clockwise

 

pilot by triggering the spark ignitor (pushing the button) until pilot

 

 

to “OFF.”

 

 

 

 

lights. Continue to hold the control knob in for about 1 ¹⁄₂ minutes

 

 

 

 

 

 

 

after the pilot is lit. Release knob and it will pop back up. Pilot should

 

 

 

 

 

 

 

remain lit. If it goes out, repeat steps 5 through 8.

 

 

 

OUT

 

IN

 

• If knob does not pop up when released, stop

 

TPTH

 

 

 

 

 

and immediately call your service technician

 

TP

I H

 

 

 

 

or gas supplier.

 

 

OFF

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

• If pilot will not stay lit after several

 

TH

 

it

 

I

 

 

 

 

OT

 

 

 

L OW

 

 

L

 

 

 

 

 

 

 

 

tries, turn the control knob to “OFF”

 

 

 

N

O

 

 

 

 

 

 

 

 

and call your service technician or

 

 

LI

 

 

 

 

 

 

P

 

 

 

 

 

 

 

TO

 

 

 

 

gas supplier.

 

 

 

 

 

 

 

 

 

 

 

 

 

9.

Turn gas control knob counterclockwise

Note: Knob cannot be turned from “PILOT” to “OFF”

 

to “ON.”

10.

Close lower control compartment.

 

unless the knob is pushed in slightly. Do not force.

TO TURN OFF GAS TO APPLIANCE

1.

Turn remote wall switch “OFF.” The pilot will remain lit for

4.

Depress gas control knob slightly and turn clockwise

 

normal service.

 

to “OFF.” Do not force.

2.

For complete shutdown, turn remote wall switch to “OFF.”

5.

Close lower control compartment.

3.Access the lower control compartment.

16