Custom Master TV Setup (Cont.)

(Continued from previous page)

5.(PTC cloning only) Transfer the TV setup menu settings to the commercial controller (PTC): 2-5-5 + MENU Mode

Note: This step is essential for successful cloning using a USB memory device / .tll file or a clone programmer. Without this step, the PTC will not contain any of the TV setup menu settings.

Note: The maximum number of channels (analog, digital, and Aux inputs) that can be transferred to the PTC is 141. An attempt to transfer more than 141 channels of any combination will result in a PTC Channel Map of exactly 141 channels; any extra channels will not be available in the PTC Channel Map. For example, if you enabled three Aux inputs in the Installer Menu and Auto Tuning found 141 channels, you must edit the TV channel lineup to decrease the number of analog/digital channels to (at most) 138 in order to accommodate the Aux inputs in the PTC Channel Map.

a)After the TV channel lineup has been edited and channel label icons added, tune to the channel (source) for which you wish to transfer TV setup menu settings.

Note: If you intend to use a clone programmer for cloning purposes, this must be either an analog channel or Aux input.

b)Access the Installer Menu, and press 2-5-5+ MENU SETTINGS on the Installer Remote to initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and then tunes through the channels in the channel lineup during the transfer. When the transfer is complete, the TV tunes back to the channel that was tuned before the transfer began.

6.(PTC cloning only / Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode

Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and

 

 

DIGITAL 19-3

 

 

 

 

custom text labels in the PTC once the Master TV Setup has been

 

 

 

MONO STEREO SAP

 

 

 

 

 

 

 

 

 

 

 

 

transferred as described in the previous step.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Access the Installer Menu, and press 2-5-4+ MENU SETTINGS on the

 

 

 

 

 

 

 

 

Installer Remote. Add/edit custom text labels and/or change icons for

 

 

 

WXYZ

 

 

 

 

the Channel-Time on-screen displays (see 2-5-4 + MENU procedural

 

Custom text label “WXYZ” created

information on page 33). Note that broadcast digital channels often

 

already have a broadcaster generated label. When you are finished,

 

 

 

in 2-5-4 + MENU Mode.

press MENU SETTINGS to exit 2-5-4 + MENU Mode.

 

 

 

 

 

 

 

 

7. Verify the TV setup.

 

 

 

 

 

 

 

 

Make sure the TV features are set per your requirements. Also, if

 

 

 

 

 

 

 

028 CH. OVERIDE

000

 

 

 

cloning the PTC, verify that the channel lineup, channel icons, and

 

 

 

 

 

 

 

 

After verifying the TV Setup, set Installer

custom text labels are correct.

8. (Recommended) Lock the channel lineup.

 

Menu item 028 CH. OVERIDE to 0.*

 

 

 

 

 

 

 

 

Access the Installer Menu. Set item 028 CH. OVERIDE to 0 and press OK to lock the channel lineup and restrict access to the TV setup menus. Press OK again to save your changes and exit the Installer Menu.*

The Master TV Setup is now ready to be copied to the predetermined cloning tool—a USB memory device (.tlx or .tll file) or a clone programmer. See cloning procedures in this document.

*This step prevents end users from accessing channel settings (i.e., the Channel Menu will be inaccessible/ grayed out).

32

206-4232