LG Electronics 42CS460S, 42CS460T, 42CS460T-ZA 4. Total Assembly line process

Only for training and service purposes

3.4 Function Check

- Check display and sound

■ Check Input and Signal items.

1) TV

2) AV (SCART / CVBS)

3) COMPONENT (480i)

4) RGB (PC : 1024 x 768 @ 60hz) (* RGB input : LD21B

only support)

5) HDMI

6) PC Audio In (* except LD21A chassis model)

* Display and Sound check is executed by Remote control.

Not to push the INSTOP key after completion if the function

inspection.

4. Total Assembly line process

4.1. Adjustment Preparation

▪ W/B Equipment condition

CA210

: CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE)

LED -> CH14, Test signal: Inner pattern(80IRE)

▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is

adjusted by Target data

* Connecting picture of the measuring instrument

(On Automatic control)

Inside PATTERN is used when W/B is controlled. Connect to

auto controller or push Adjustment R/C POWER ON →

Enter the mode of White-Balance, the pattern will come out.

* Auto-control interface and directions

(1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).

(2) Adhere closely the Color analyzer(CA210) to the module

less than 10 cm distance, keep it with the surface of the

Module and Color analyzer's prove vertically.(80° ~ 100°).

(3) Aging time

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 5 minutes.

- Using 'no signal' or 'POWER ONLY' or the others, check

the back light on.

▪ Auto adjustment Map(using RS-232C to USB cable)

RS-232C COMMAND

[CMD ID DATA]

Wb 00 00 White Balance Start

Wb 00 ff White Balance End

Color Temperature : COOL, Medium, Warm.

One of R Gain/G Gain/ B Gain should be kept on 0xC0, and

adjust other two lower than C0.(When R/G/B Gain are all

C0, it is the FULL Dynamic Range of Module)

* Manual W/B process using adjust Remote control.

▪ After enter Service Mode by pushing "ADJ" key,

▪ Enter White Balance by pushing "►" key at "8. White

Balance".

* After you finished all adjustments, Press "In-start" key and

compare Tool option and Area option value with its BOM, if

it is correctly same then unplug the AC cable. If it is not

same, then correct it same with BOM and unplug AC cable.

For correct it to the model's module from factory Jig model.

* Push the "IN STOP" key after completing the function

inspection. And Mechanical Power Switch must be set

“ON”.

Mode Temp Coordinate spec Target

Cool 13,000k X=0.269 (±0.002)

Y=0.273 (±0.002)

X=0.271

Y=0.276

LAMP

Inner pattern

(204gray,

80IRE)

Medium 9,300k X=0.285 (±0.002)

Y=0.293 (±0.002)

X=0.287

Y=0.296

Warm 6,500k X=0.313 (±0.002)

Y=0.329 (±0.002)

X=0.315

Y=0.332

Full White Pattern CA-210

COLOR

ANALYZER

TYPE : CA-210

RS-232C Communication

RS-232C COMMAND

[CMD ID DATA] MIN

CENTER

(DEFAULT) MAX

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 192

G Gain jh Jb je 00 172 192 192 192

B Gain ji Jc jf 00 192 192 172 192

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance ►

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

White Balance

Color Temp.

R-Gain

G-Gain

B-Gain

R-Cut

G-Cut

B-Cut

Test-Pattern

Backlight

Reset

Cool

172

192

100

To Set