Installer Menu (Cont.)
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PC- based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a onetime automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed.
088 - EN NOISE MUTE (Enable Noise Mute)
Applicable for analog channels only. If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, Key Lock is enabled, which means that all display panel joystick button functions will be locked, i.e.,
091 - HDMI2 ENABLE
Set to 1 to enable HDMI 2 input in DTV Mode. Set to 2 to enable HDMI 2 input in PC Mode. Set to 0 to disable display panel HDMI 2 input.
092 - HDMI3 ENABLE
Set to 1 to enable HDMI 3 input in DTV Mode. Set to 2 to enable HDMI 3 input in PC Mode. Set to 0 to disable display panel HDMI 3 input.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function Menu, if Function Menu is available (i.e., TV is not in
096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up:
0 | = Set By System | 1 | = 4:3 |
2 | = 16:9 (default) | 3 | = Just Scan |
4 | = Zoom |
|
|
Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0.
097 - AUDIO OUTPUT
Determines availability and signal type/level (fixed speaker, variable speaker, or fixed line level [amplifier]) of the audio output to be used by external audio equipment connected to the Speaker Out jack on the TV. Set to 0 to disable audio output. Otherwise, see the table below and set as required in accordance with audio equipment.
| Value | Status |
|
Speaker Output | 1 | Fixed 0.01 Watts | |
|
|
| |
| 2 | Fixed 0.03 Watts | |
| 3 | Fixed 0.05 Watts | |
|
|
| |
| 4 | Fixed 0.10 Watts | |
| 5 | Fixed 0.20 | Watts |
|
|
|
|
| 6 | Fixed 0.50 | Watts |
| 7 | Fixed 1.00 | Watt (default) |
|
|
| |
| 8 | Control with volume | |
|
|
| |
Line Output | 9 | Fixed line level (typically 400 mVrms ± | |
|
| 100 mVrms @10KΩ) output | |
See also Reference section, “External Stereo Speaker Setup.”
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to disable the Pro:Centric application. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.
In order to retrieve the Pro:Centric application, when enabled (for Flash or GEM Mode), the TV must be turned OFF/ON two times. Once you exit the Installer Menu, turn OFF the TV for at least one minute. When you turn the TV back ON, the TV will start the appropriate library based on the setting of this item. Wait until TV programming appears on the display, and then turn the TV back OFF, this time for a few minutes, to initiate the application down- load. When you turn the TV back ON, press the PORTAL key on the Installer Remote, and verify that the Pro:Centric application appears on the display.
Note: This item is not available in the Installer Menu when item 119 DATA CHANNEL is set to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 202.
•1 (dimmest
•101 (dimmest
•201 Automatic Static Back Lighting: The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting.
•202 Automatic Dynamic Back Lighting: The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting and depending upon the picture level of the current program.
29 |