Linear DF-31/EC manual

DF-31/EC			1. SENSOR & MAGNET DETAIL			2. SET SENSOR SWITCH		3. EXAMPLE SENSOR LOCATIONS
			SENSOR HAS BUILT-IN SWITCH ON SIDE WITH NOTCH.						SENSOR
			MAGNET CAN ACTIVATE SWITCH UP TO 1/2" AWAY.
			WHEN MOUNTING SENSOR, ALIGN MAGNET TO NOTCH.						ON FRAME
									MAGNET
			REMOVE PLASTIC BATTERY TAB						ON DOOR
DOOR/WINDOW
			PRIOR TO INSTALLATION BY
SENSOR			PULLING STRAIGHT OUT
For Use with DF-16/EC					SENSOR
Security Console			NOTCH ON
			SIDE OF
Installation			SENSOR
			ALIGN MAGNET			SET SWITCH TO DELAYED
Instructions						FOR ENTRY/EXIT DOOR
			NEXT TO NOTCH			SET SWITCH TO INSTANT
			ON SENSOR
						FOR WINDOWS OR
									MAGNET
						NON-ENTRY DOORS
									ON WINDOW
(760) 438-7000 • FAX (760) 438-7043			MAGNET	1/2" SPACE					SENSOR
www.linearcorp.com				MAXIMUM					ON FRAME
4. PROGRAM SENSOR INTO CONSOLE			5. EXAMPLE SENSOR MOUNTING ON DOOR			6. EXAMPLE SENSOR MOUNTING ON WINDOW		7. OPTIONAL MAGNET SPACER
START IN		SEND SIGNAL
OFF MODE		FROM SENSOR							USE SPACER WHEN
ENTER YOUR	PRESS	ENTER AN				MOUNT SENSOR			SURFACES ARE
SECRET CODE	LEARN	UNUSED SENSOR					ALIGN MAGNET		UNEVEN
		NUMBER				PLATE TO FRAME
							PLATE NEXT TO
LEARN BUTTON							SENSOR PLATE
							AND ATTACH TO
						SPACE BELOW
							WINDOW
			MOUNT SENSOR			PLATE IS REQUIRED
						TO SNAP SENSOR
			PLATE TO FRAME
						ONTO PLATE
									HOOK SPACER TO
			1/2" MAXIMUM			1/2" MINIMUM			MAGNET PLATE
									AND ROTATE TO
			SPACE BETWEEN						LOCK IN PLACE
1			SENSOR AND
					ALIGN MAGNET
			MAGNET PLATES
					PLATE NEXT TO	SNAP SENSOR ONTO			R&TTE VAEE 28357, EMC, SFT, ETS
PRESS SENSOR					SENSOR PLATE
						MOUNTING PLATE
OR MOVE MAGNET		HOLD OFF BUTTON	SNAP SENSOR ONTO		AND ATTACH TO				Linear Corporation declares that the apparatus DF-31/EC
TO SEND SIGNAL		FOR 3 SECONDS WHEN			DOOR
			MOUNTING PLATE
		FINISHED TO EXIT							complies with the essential requirements and other relevant
		LEARN MODE							provisions of Directive 1995/5/EC.
8. TEST SENSOR			9. LABEL SENSORS			10. CHANGING BATTERIES			INTERNATIONAL WARRANTY
			STATUS INDICATOR					This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
						WHEN CONSOLE INDICATES A SENSOR		Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who
			SHOULD LIGHT
SENSOR LIGHT								buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product
			WHEN SENSOR IS OPEN			LOW BATTERY, OPEN SENSOR CASE AND		to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if
SHOULD		OPEN DOOR				GENTLY LIFT UP END OF BATTERY CLAMP,		any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages
								arising out of or in connection with use or performance of this product or other indirect damages with
GLOW FOR						SLIDE BATTERIES OUT
		OR WINDOW						respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied
TWO SECONDS								warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until
								Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other
								warranties express or implied.
						NOTE: USE OF EXCESSIVE FORCE ON		For	warranty service on Linear equipment return product, at sender’s expense to: Linear Hong Kong
						BATTERY CLAMP WILL RESULT IN DAMAGE		19/F	Hounor Industrial Centre,6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department
			1					REPAIRS POLICY
								Charges will be made for equipment that is not of warranty, shows customer abuse, or is damaged by the effects
							+	of lightning, water, fi re, or other abnormal happenings.
								Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment
							-	at Linear’s discretion.
								The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return
				USE LABELS PROVIDED		LIFT	+	shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be
								billed for the return shipping and handling charges on “out of warranty” products.
				TO IDENTIFY SENSORS			-
								There will be a 50% expedite fee for any express requests.
							INSTALL TWO	The International Sales Manager must be notifi ed prior to the return of product to Linear. All international returns
								must have an International Repair Authorization number (IRA#). The number must be marked on all packages.
							DURACELL	Failure to do so will cause delays in processing.
							TYPE DL 2032	IMPORTANT !!!
								Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless
							BATTERIES (+)
								signaling. However, there are some limitations which must be observed.
CONSOLE IN							SIDE UP	The radios are required to comply with local rules and regulations as radio devices. As such, they have limited
								transmitter power and therefore limited range.
CHIME MODE								A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that
							REMOVE BATTERIES	occur on or near their operating frequencies, regardless of code settings.
SHOULD DING-DONG						IF NECESSARY	FROM THIS END	Changes or modifi cations to the device may void regulatory compliance.
								Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
						PUSH IN SLOT TO REMOVE		A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
						SENSOR FROM MOUNTING PLATE		dealer, and these facts should be communicated to the ultimate users.

Copyright © 2003 Linear Corporation 220837 A