Linear DF-16/EC, DF-54/EC manual

DF-54/EC	1. MOTION DETECTOR DETAIL		2. TYPICAL INSTALLATION
	MOTION		DON'T POINT AT HEAT SOURCES
BY	DETECTOR		(HEATERS, ETC.), WINDOWS, OTHER
	LENS		MOTION DETECTORS OR DOOR/WINDOW
MOTION
			TRANSMITTERS
DETECTOR
For Use with DF-16/EC			FRONT				MOTION
Security Console						DETECTOR
			ROOM
Installation		WALK				(FOR INDOOR
		TEST		BEDROOM			USE ONLY)
Instructions		BUTTON					MOUNT
			CONSOLE		BATH	DETECTOR
							SO THAT
	CASE			KITCHEN		INTRUDER
	LOCKING					WILL CROSS
	SCREW						BEAMS
(760) 438-7000 • FAX (760) 438-7043	(ON BOTTOM)
www.linearcorp.com
4. CONNECT BATTERY	5. MOUNT MOTION DETECTOR BASE		6. PROGRAM DETECTOR INTO CONSOLE
		MOUNTING THE DETECTOR	START IN					PUSH WALK
		IN A CORNER IS PREFERRED
REMOVE			OFF MODE					TEST BUTTON
SCREW		AFTER MOUNTING, SNAP	ENTER YOUR	PRESS	ENTER AN		TO SEND SIGNAL
								FROM MOTION
AND OPEN		DETECTOR ONTO BASE	SECRET CODE	LEARN	UNUSED SENSOR
								DETECTOR
CASE		AND REPLACE CASE SCREW			NUMBER
	USE CENTER	USE SIDE HOLES
	HOLES FOR	FOR CORNER
	WALL	MOUNTING	LEARN BUTTON
	MOUNTING
CONNECT 9-VOLT ALKALINE	PUNCH OUT REQUIRED HOLES
BATTERY TO BATTERY CLIP					WALK
(PLUS SIDE UP)	FOR SCREW MOUNTING				TEST
		MOUNT	1		BUTTON
NOTE:	NOTE:	DETECTOR
		6-8 FEET
WAIT 5 MINUTES AFTER	THE DETECTOR CAN
		HIGH	HOLD OFF BUTTON
CONNECTING BATTERY
	BE MOUNTED WITH
FOR DETECTOR			FOR 3 SECONDS WHEN
	DOUBLE STICK TAPE,
TO STABILIZE			FINISHED TO EXIT
			LEARN MODE
8. ALARM TEST MOTION DETECTOR	9. REPLACING MOTION DETECTOR BATTERY		10. IMPORTANT DETECTOR INFORMATION
			1.
PLACE CONSOLE IN THE	WHEN CONSOLE INDICATES A LOW BATTERY		1. The motion detector can only trigger the alarm
			when the Console is in Away Mode.
AWAY MODE	FOR THIS SENSOR:
			2. Except in “Walk Test”, the detector must see no
	REMOVE		motion for fi ve minutes before walking in front of
			the unit will send an alarm signal.
	SCREW
STAY OUT OF THE MOTION	AND OPEN		3. When the Console is in Away Mode, the motion
	CASE
DETECTION PATTERN AREA			detector will cause an instant alarm unless a
FOR AT LEAST FIVE MINUTES			delayed perimeter door/window sensor is triggered
AFTER FIVE MINUTES, WALKING			fi rst.
IN FRONT OF THE MOTION DETECTOR			4. Operating temperature range:
SHOULD TRIGGER THE ALARM
			+32° to +120° F (0° to +49° C)
	REPLACE THE BATTERY WITH
	A FRESH 9-VOLT ALKALINE
	BATTERY (PLUS SIDE UP)		R&TTE VAEE 27837, EMC, SFT, ETS
	USE ALKALINE
	BATTERY ONLY
	SNAP DETECTOR ONTO BASE		Linear Corporation declares that the apparatus
	AND REPLACE CASE SCREW
			DF-54/EC complies with the essential requirements
PLACE CONSOLE IN OFF MODE	WHEN FINISHED
			and other relevant provisions of Directive 1995/5/EC.
TO STOP SIREN, CHECK THAT SENSOR	NOTE: WAIT 5 MINUTES AFTER REPLACING
STATUS LIGHT IS BLINKING.
	BATTERY FOR DETECTOR TO STABILIZE

3. MOTION DETECTION PATTERN

MOTION		9 METERS
DETECTOR
IN CORNER
	METERS9	DETECTION
		AREA
		TOP
		VIEW

2-3 METERS	SIDE
	VIEW
9 METERS
7. WALK TEST MOTION DETECTOR

PUSH
WALK	WALK IN FRONT OF
TEST	UNIT WHILE WATCHING
BUTTON	RED LIGHT

UNIT WILL STAY INWALK TEST MODEFOR 4 MINUTES AFTERPRESSING WALK TESTBUTTON THEN AUTOMATICALLYRETURN TO "OPERATE" MODEVERIFY THAT DETECTIONPATTERN COVERS DESIREDAREA & THAT CONSOLESTATUS INDICATOR LIGHTSWHEN MOTION IS DETECTEDNOTE:AFTER INITIAL SETUP,WALK TEST UNIT YEARLY

INTERNATIONAL WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to

the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of

Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. For warranty service on Linear equipment return product,

at sender’s expense to:

Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department

REPAIRS POLICY

Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged by the effects of lightning, water, fire, or other abnormal happenings.Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s discretion.The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products.There will be a 50% expedite fee for any express requests.The International Sales Manager must be notified prior to the return of product to Linear. All international returns must have an International Repair Authorization number (IRA#). The number must be marked on all packages. Failure to do so will cause delays in processing. IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed. The radios are required to comply with local rules and regulations as radio devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifications to the device may void regulatory compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

Copyright © 2003 Linear Corporation 210948 B