Linear DXR-701 manual

DXR-701					PRODUCT DESCRIPTION			A nine-inch wire lead serves as the receiver’s antenna. The red program
					The DXR-701 is a digital receiver with an isolated relay output designed for use
					with Linear’s DX Format transmitters. This receiver can be used in a variety			indicator lights during RF reception. The installer can verify that signals are
					of remote control applications. When the receiver detects a signal from a			being sent from transmitters and diagnose interference problems by viewing
			BY		transmitter programmed into its memory, the relay output activates. The relay			the indicator. The indicator also lights during memory programming/erasing and
SINGLE-					has four optional output configurations.			flashes to count the number of transmitters in memory. The program button and
					In a typical installation, the receiver is connected to an alarm control panel, door			indicator function as follows:
CHANNEL					activate or control the device. The receiver should be mounted with the supplied
					strike, camera, high current relay or some other device. A transmitter is used to			FUNCTION	PROGRAM BUTTON		PROGRAM INDICATOR
DIGITAL
					mounting bracket indoors or inside a weather resistant non-metallic housing.			OPERATION	RELAY		ARE RECEIVED, BLINKS AS
								NORMAL	RELEASES LATCHED
RECEIVER					The digital DX code format features over a million possible codes. The DX			PROGRAMMING	PRESS AND RELEASE		INTERFERENCE IS RECEIVED
					is required. Receivers must be programmed to the transmitter’s code before						LIGHTS FOR 3 SECONDS FOR
					transmitters are precoded at the factory to unique codes, so no field coding
					system testing and operation. Up to 32 transmitters can be programmed			MEMORY			PROGRAMMING
Installation
					into the receiver’s memory. The memory is retained, even without power.			CHECKING	PRESS UNTIL BLINK AND		BLINKS THE NUMBER OF
Instructions					The unit can be powered from a 11-17 VDC or 12-16 VAC power source. The			MEMORY	RELEASE		TRANSMITTERS IN MEMORY
					relay’s normally open and normally closed contacts can switch up to 1 amp at				PRESS AND HOLD
											AFTER BLINKING COUNT. A
					24 volts AC/DC.
								ERASING	THROUGH THE COUNT
								MEMORY	AND HOLD FOR 4		PAUSE THEN A SINGLE BLINK
					Cutting jumpers select how the relay activates. The factory setting causes						AS MEMORY IS ERASED
		(760) 438-7000 • FAX (760) 438-7043							SECONDS MORE
					the relay to engage for four seconds each activation. Optionally, the relay
	USA & Canada (800) 421-1587 & (800) 392-0123
		Toll Free FAX (800) 468-1340			can be set to engage for one second, toggle on with one activation then off
		www.linearcorp.com			with the next, or latch engaged until reset by pressing the program button.
		DXR-701 FEATURES			RELAY OPTION JUMPERS				MOUNTING RECEIVER
ANTENNA		POWER			NOTE:						MOUNTING NOTES:
					IF RELAY OPTION IS GOING TO	TERMINALS			USE SCREWS TO	1. MOUNT RECEIVER AS HIGH AS
		TERMINALS			BE CHANGED: REMOVE POWER,				ATTACH THE
				RELAY	CUT JUMPERS, APPLY POWER,	JUMPER			MOUNTING	POSSIBLE FOR BEST RADIO RANGE
					ERASE MEMORY, THEN RE-				BRACKET	2. KEEP RECEIVER AWAY FROM METAL
				TERMINALS	PROGRAM ALL TRANSMITTERS	WJ1
										OBJECTS THAT CAN DECREASE RADIO
PROGRAM										RANGE BY SHIELDING THE SIGNAL
					OPEN CASE					3. KEEP RECEIVER AWAY FROM
INDICATOR					WITH SMALL
						JUMPER				MOTORS, FANS AND OTHER
					SCREWDRIVER					ELECTRICAL DEVICES THAT MAY
						WJ2
										CAUSE INTERFERENCE AND REDUCE
						ANTENNA			SNAP RECEIVER	RADIO RANGE
									ONTO BRACKET
						RECEIVER CIRCUIT BOARD		BRACKET CAN			CORNER HOLE IS
								MOUNT IN THREE			SHARED FOR
								PLACES			LOCATIONS 2 & 3
					RELAY OPTION	JUMPER WJ1	JUMPER WJ2				LOCATION 2
					4 SECOND LATCH	SOLID	SOLID
PROGRAM								LOCATION 1
					1 SECOND LATCH	CUT	SOLID
BUTTON
					LATCH UNTIL RESET ++	SOLID	CUT
			N.O. COM N.C.		TOGGLE ON AND OFF ++	CUT	CUT
11-17 VDC					BE SURE POWER IS OFF WHEN CUTTING JUMPERS						LOCATION 3
12-16 VAC					++ CAN BE RESET BY PUSHING THE PROGRAM BUTTON ONCE			PULL ANTENNA
								STRAIGHT
	TERMINAL CONNECTIONS				PROGRAMMING MEMORY				CHECKING MEMORY
DXR-701			DXR-701		1. PRESS AND RELEASE
TERMINALS			TERMINALS	CAMERA				1. PRESS PROGRAM BUTTON
					PROGRAM BUTTON.
								AND HOLD FOR ABOUT TWO
N.C.		N.C. OR N.O.	N.C.	& VCR
		ALARM			2. PROGRAM INDICATOR			SECONDS UNTIL INDICATOR
COM			COM					LIGHTS THEN RELEASE.
		LOOP			WILL LIGHT IF THERE IS
N.O.		ALARM PANEL	N.O.		ROOM IN MEMORY FOR			2. COUNT THE NUMBER OF
					ANOTHER TRANSMITTER.
		AUX.		POWER				INDICATOR BLINKS, THIS IS
					(32 TRANSMITTERS MAX.)
								THE TOTAL NUMBER OF
		POWER		SUPPLY
					3. SEND SIGNAL FROM			TRANSMITTERS PROGRAMMED.
ALARM PANEL CONNECTION			SECURITY CAMERA CONNECTION		TRANSMITTER, INDICATOR
					WILL FLICKER AS SIGNAL IS
1 SECOND RELAY OPTION			LATCHING RELAY OPTION
					RECEIVED.
DXR-701			DXR-701	LOAD
TERMINALS	ELECTRIC		TERMINALS		4. REPEAT THE ABOVE THREE
					STEPS FOR EACH ADDITIONAL
N.C.	DOOR STRIKE		N.C.	EXTERNAL
					TRANSMITTER.
COM		STRIKE	COM	RELAY					PUSH UNTIL
		POWER
N.O.			N.O.		NOTE:				INDICATOR LIGHTS
		XFMR
		RADIO			THE RECEIVER CAN MEMORIZE
				POWER	EACH TRANSMITTER MORE THAN
		POWER		SUPPLY	ONCE. TO PREVENT DUPLICATE				NOTE: DO NOT CONTINUE TO PRESS
		XFMR
					ENTRIES, PROGRAM EACH				BUTTON OR MEMORY WILL BE ERASED
DOOR STRIKE CONNECTION			EXTERNAL RELAY CONNECTION		TRANSMITTER INTO RECEIVER
					ONLY ONCE.
4 SECOND RELAY OPTION			TOGGLE RELAY OPTION
		SYSTEM TESTING			ERASING MEMORY			LINEAR LIMITED WARRANTY
1. ACTIVATE EACH TRANSMITTER,								This Linear product is warranted against defects in material and workmanship for twelve (12)
					1. PRESS PROGRAM BUTTON			months. The Warranty Expiration Date is labeled on the product. This warranty extends only
ONE AT AT TIME.								to wholesale customers who buy direct from Linear or through Linear’s normal distribution
					AND CONTINUE TO HOLD IT
								channels. Linear does not warrant this product to consumers. Consumers should inquire from
					THROUGH THE COUNT OF THE
2. LISTEN FOR RELAY CLICK IN								their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or
					TRANSMITTERS.
RECEIVER.								liabilities on the part of Linear Corporation for consequential damages arising out of or in
								connection with use or performance of this product or other indirect damages with respect
					2. CONTINUE TO HOLD THE
3. VERIFY THAT THE DEVICE CONNECTED								to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.
					BUTTON AFTER THE COUNT
								All implied warranties, including implied warranties for merchantability and implied warranties
TO THE RECEIVER RESPONDS.					UNTIL THE INDICATOR BLINKS
								for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear
					ONE MORE TIME (ABOUT
								Corporation Warranty is in lieu of all other warranties express or implied.
4. TEST PORTABLE TRANSMITTERS IN					FIVE SECONDS AFTER THE
								All products returned for warranty service require a Return Product Authorization Number (RPA#).
VARIOUS LOCATIONS TO DETERMINE					COUNT).			Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other important details.
SYSTEM PERFORMANCE.					3. ALL TRANSMITTERS				IMPORTANT !!!
								Linear radio controls provide a reliable communications link and fill an important need in portable
					PROGRAMMED INTO MEMORY			wireless signalling. However, there are some limitations which must be observed.
					WILL BE ERASED.			• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations
								as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
								• A receiver cannot respond to more than one transmitted signal at a time and may be blocked
								by radio signals that occur on or near their operating frequencies, regardless of code settings.
								• Changes or modifications to the device may void FCC compliance.
								• Infrequently used radio links should be tested regularly to protect against undetected
								interference or fault.
					PUSH AND HOLD BUTTON			• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
								distributor or dealer, and these facts should be communicated to the ultimate users.
					FOR FIVE SECONDS AFTER
					THE TRANSMITTER COUNT
								Copyright © 2002 Linear Corporation			220463 A