Linear GT-30 manual

	DESCRIPTION	PROGRAM TRANSMITTER INTO RECEIVER
	Linear’s GT series of digital transmitters are wireless	For INTELLICODE™ and CodeDodger™ systems, refer
	radio controls designed for use with Genie Pro®	to the instructions provided with the receiver to set it to a
GT-30	INTELLICODE™, Overhead Door® CodeDodger™, and	“learning” mode. Activate the desired transmitter button
	Linear® Model AM-RGR access control receivers. The	to program that button into the receiver
	rolling-code GT radio format provides additional security
	by changing the transmitter’s code with each use.
	The GT-30 is a three-button transmitter that sends a
	unique code for each button.Typically, one button is used
DIGITAL	to operate a community access gate, another button can
TRANSMITTER	activate the individual’s garage door, and a third button
	can control an additional door or other device.
	The transmitter is powered by two Type 2016 “coin cell”
	batteries. A red indicator lights when the transmitter is	Linear’s Model AM-RGR receivers detect the signal from
	activated. A removable spring steel visor clip is supplied	the transmitter and pass its digital code to the AM/II
Operation Instructions	attached to the back of the transmitter.	access controller.
	☞ NOTE: INTELLICODE™, CodeDodger™, Genie Pro®, and Overhead	GT-30 transmitters are manufactured and sold “Block
	Door® are registered trademarks of Overhead Door Corporation.	Coded” from the factory. Each block of transmitters is
		labeled with the starting and ending block code number,
(760) 438-7000 • FAX (760) 438-7043		along with a facility code number. Refer to the AM/II
USA & Canada (800) 421-1587 & (800) 392-0123		instructions for details on how to program the block and
Toll Free FAX (800) 468-1340		facility code numbers into the controller.
www.linearcorp.com
REPLACING BATTERIES		LINEAR LIMITED WARRANTY
When the red indicator on the face of the transmitter		This Linear product is warranted against defects in material and workmanship for twelve (12)
	2	months. The Warranty Expiration Date is labeled on the product. This warranty extends only
lights dimly, or not at all during activation, the batteries
		to wholesale customers who buy direct from Linear or through Linear’s normal distribution
need replacing.	CAREFULLY REMOVE	channels. Linear does not warrant this product to consumers. Consumers should inquire from
	CIRCUIT BOARD	their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or
		liabilities on the part of Linear corporation for consequential damages arising out of or in
		connection with use or performance of this product or other indirect damages with respect
		to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.
		All implied warranties, including implied warranties for merchantability and implied warranties
		for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear
1		Corporation Warranty is in lieu of all other warranties express or implied.
		All products returned for warranty service require a Return Product Authorization Number (RPA#).
REMOVE VISOR		Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
		IMPORTANT !!!
CLIP AND SCREW	3 INSTALL TWO
		Linear radio controls provide a reliable communications link and fill an important need in portable
	TYPE 2016 BATTERIES
		wireless signaling. However, there are some limitations which must be observed.
	PLUS (+) SIDE DOWN
		• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
		devices. As such, they have limited transmitter power and therefore limited range.
		• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
		signals that occur on or near their operating frequencies, regardless of code settings.
		• Changes or modifications to the device may void FCC compliance.
		• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
		• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor
		or dealer, and these facts should be communicated to the ultimate users.
		• This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) This device
		may not cause harmful interference and (2) this device must accept any interference received, including
	REASSEMBLE	interference that may cause undesired operation.
	UNIT WHEN
	FINISHED	Copyright © 2000 Linear Corporation	217130 A