Mitsubishi Electronics FX2NC-ENET-ADP specifications

Guideline for the safety of the user and protection of the FX2NC-ENET-ADP.

This manual provides usage information for the FX2NC-ENET-ADP Ethernet

adapter. The manual has been written to be used by trained and competent

personnel.

Notes on the symbols used in this manual

At various times throughout out this manual certain symbols will be used to

highlight points of information which are intended to ensure the users personal

safety and protect the integrity of equipment. Whenever any of the following

symbols are encountered, its associated note must be read and understood. Each

of the symbols used will now be listed with a brief description of its meaning.

Hardware Warnings

1)Indicates that the identified danger WILL cause physical and

property damage.

2)Indicates that the identified danger could POSSIBLY cause

physical and property damage.

3)Indicates a point of further interest or further explanation.

DISPOSAL PRECAUTIONS

•When disposing of this product, treat it as industrial waste.

INSTALLATION PRECAUTIONS

•Use the module in an environment that meets the general

specifications contained in this manual. Using this module in an

environment outside the range of the general specifications could

result in electric shock, fire, erroneous operation, and damage to or

deterioration of the product.

•Do not disassemble or modify the module. Doing so may cause

failure, malfunction, injury, or fire.

TRANSPORTATION AND MAINTENANCE PRECAUTIONS

•During transportation avoid any impact as the module is a precision

instrument. Doing so could cause trouble in the module.

•It is necessary to check the operation of module after transportation,

in case of any impact damage.

●Note Concerning the CE Marking●

The CE marking does not guarantee that an entire mechanical module produced in

accordance with the contents of t he notification comply wi th the following standard s.

Compliance to EMC standards of the entire mechanical module should be checked by

the user / manufacturer.

Standards with which this product complies

Type: Programmable Controller (Open Type Equipment)

Models:Products manufactured:

from April 1st, 2004 to April 30th, 2006 are compliant with

EN61000-6-4 and EN61131-2:1994+A11:1996+A12:2000 and EN61000-6-2

after May 1st, 2006 are compliant with EN61131-2:2003

For more details please contact the local Mitsubishi Electric sales site.

- Notes for compliance to the EMC regulation.

It is necessary to install the FX2NC-ENET-ADP module in a shielded metal control

panel.

1. Associated Manuals

For GX Developer and MX Component, refer to the operation manual respectively.

2. Outline of Product

The FX2NC-ENET-ADP is an Ethernet adapter of 10BASE-T specifications for the

FX1S, FX1N, FX2N and FX2NC Series.

The FX2NC-ENET-ADP enables the upload, download, monitor, and test of a program

from the personal computer (GX Developer or MX Component) via Ethernet.

3. Installation

Caution

•Use only in the environments specified under the general specifications

in the manual.

Do not use the product in environments with excessive or conductive

dust, corrosive (including salt breeze, Cl2, H2S, SO2, NO2, etc.) or

flammable gas, oily smoke, moisture or rain, excessive heat, regular

impact shocks or excessive vibration, as it may result in electrical shock,

fire, malfunction, damage or deterioration of the product.

•Make sure to shut off the external power before installing or wiring it.

Electric shock or serious damage to the product may occur, if the external

power is not disconnected.

•Never drop wire chips or shavings into the ventilation slits when drilling

screw holes or performing wiring, as they may cause fire, breakdown, or

malfunction.

•Securely install the FX2NC-ENET-ADP to the designated port.

A poor connection may result in malfunction.

Electromagnetic Compatibility

Standards (EMC) Remark

EN61000-6-4:2001

Electromagnetic compatibility

-Generic standards - Emission standard

for Industrial environment

Compliance with all relevant aspects of the

standard. (Radiated Emissions and Mains

Terminal Voltage Emissions)

EN61131-2:1994/A11:1996/A12:2000

Programmable controllers

-Equipment requirements and tests

Compliance with all relevant aspects of the

standard. (RF Immunity, Fast transients,

ESD and Damped oscillatory wave)

EN61000-6-2:2001

Electromagnetic compatibility

-Generic standards Immunity for

industrial environments.

Compliance with all relevant aspects of the

standard. (RF immunity, Fast transients,

ESD, Conducted, Surges, Power

magnetic fields, Voltage dips and Voltage

interruptions)

EN61131-2: 2003

Programmable controllers

-Equipment requirements and tests

Compliance with all relevant aspects of the

standard.

(Radiated Emissions, Mains Terminal

Voltage Emissions, RF immunity, Fast

Transients, ESD, Surge, Voltage drops

and interruptions, Conducted and Power

magnetic fields)

Manual name Manual No. Description

FX1S HARDWARE MANUAL JY992D83901

Describes the hardware of the

FX Series PLC such as

specifications, wiring, and

installation.

FX1N HARDWARE MANUAL JY992D89301

FX2N HARDWARE MANUAL JY992D66301

FX2NC HARDWARE MANUAL

(DSS/DS)

(D/UL)

JY992D76401

JY992D87201

FX PROGRAMMING MANUAL II JY992D88101

Describes the instructions

available in the FX1S/FX1N/

FX2N/FX2NC Series PLC.

FX Configurator-EN

OPERATION MANUAL JY997D20501

Describes operation details of

FX Configurator-EN

Configuration Software.

FX1N-CNV-BD Special Adapter

Connection Board JY992D84701

Describes matters related to the

installation of the boards.

FX2N-CNV-BD Special Adapter

Connection Board JY992D63601

3.1 How to Install to FX Series PLC

Installation to FX1S/FX1N/FX2N

Turn OFF the PLC before beginning any

work.

1)Remove the panel cover from the top

face of the main unit.

2)Take off the resin cover from the left

side of the main unit.

3)Install the following board to the port

on the main unit.

4)Affix the above board using the

supplied M3 screws.

Tightening torque: 0.3 to 0.6 N·m

5)Connect the built-in cable of the

FX2NC-ENET-ADP to the port on the left side of the board.

Installation to FX2NC

Turn OFF the PLC before beginning any work.

1)Remove the cover from the special adapter port provided on the left side of the

main unit.

2)Connect the built-in cable of the FX2NC-ENET-ADP to the special adapter port.

3.2 Installation to a Panel Face

Direct installation to the panel face

Directly attach to the panel face using 2 sets of a

screw (M4), a spring washer, and a flat washer

in the mounting holes.

Tightening torque: 0.7 to 1.0 N·m

For the pitch and positions of mounting screw

holes, refer to the external dimensions.

Mounting on DIN rail

Affix the FX2NC-ENET-ADP to the DIN rail,

DIN46277 (35 mm (1.37") wide).

Dismounting from DIN rail

Slightly pull down the DIN rail mounting clip

using a tool such as a slotted screwdriver. Pull

down the clip further, and the rail will be locked

with the clip left open.

4. System Configuration

Board name Corresponding

model

FX1N-CNV-BD FX1S/FX1N

FX2N-CNV-BD FX2N

PLC Ethernet adapter LAN cable

FX1S/FX1N PLC + FX1N-CNV-BD

FX2NC-ENET-ADP

Twisted pair cable

Category 5(e) STP or 3

STP (straight cable)

FX2N PLC + FX2N-CNV-BD

FX2NC PLC

X1X3

Y0Y2

Installation to

FX1S/FX1N/FX2N

Installation to

FX2NC

ENET

-ADP

Screws

FX Series

PLC

FX Series

PLC

DIN rail

ENET

-ADP

Detach To lock the tab

2NC

-ENET-ADP

HUB LAN cables

. . . .

,FX

LAN

cables

2NC

•Applicable version of GX Developer/MX Component

5. Product Specification

5.1 Specifications

The general specifications of FX2NC-ENET-ADP are same as those of the FX

Series PLC except the following items.

5.2 Outside dimensions and name of each part

1)Mounting hole (2-φ4.2)

Used when FX2NC-ENET-ADP is mounted directly.

Not used when the module is mounted on DIN rail.

2)POWER LED (green)

Lit while 5V DC power is supplied from the PLC.

3)LINK LED (green)

Lit while the HUB is connected by an RJ45 connector and the power is on.

4)ACT LED (red)

Lit while transferring data with connected Ethernet.

5)SD LED (red)

Lit while sending data to the connected PLC.

6)RD LED (red)

Lit while receiving data from the connected PLC.

7)Connecting cable

Used to connect the main unit.

8)RJ45 connector

Connects the Ethernet cable.

Software Applicable Version With FX Configurator-EN

GX Developer Ver. 8.12N or later Ver. 8.25B or later

MX Component Ver. 3.05F or later Ver. 3.08J or later

Item Description

General

specifications

Withstand voltage 500V AC for 1

min

Conforms to JEM-

1021, between all

terminals together

and grounding

terminal

Insulation resistance 5 MΩ or more by

500V DC megger

Power supply

specifications

Supply voltage/

current 5V DC, 135 mA (supplied from PLC)

Performance

specifications

Baud rate 10Mbps

Protocol CSMA/CD(IEEE802.3)

Transmission media 10BASE-T

Topology Star type

Communication

method Full duplex

Connector

To Ethernet RJ45 connector

To ground 3 pins

(However, internally short-circuited)

Mass 0.1 kg (0.22 lbs)

FX -ENET-ADP

2NC

POWER

ACT

LINK

2-φ4.2(0.17")

16.1(0.64")

(to screw holes)

2) 3)

6) 7)

19.1

(0.76")

45 (1.78")

(to center of DIN rail)

90(3.35")

11)

10)

74(2.92")

7(0.28")

(Height of screw hole)

65.5(2.58")

(between screw holes)

10

(0.40")

78(3.08")

Unit: mm (inches)

9)Terminal block for grounding

Internally short-circuited.

Applicable cable: AWG 17 to 14

Tightening torque: 0.4 to 0.5 N·m

10)DIN rail mounting hook

11)DIN rail mounting groove

5.3 Connector pin arrangement

The RJ45 connector in the FX2NC-ENET-ADP has the following pin arrangement.

5.4 Used cable

STP (Shielded twisted pair) cable Category 5(e) or 3

6. Wiring

6.1 Cautions on wiring

Wiring Precaution

•Cut off all phases of external power source before installation or

performing wiring work in order to avoid electric shock or damage to

the product.

Wiring Precaution

•The grounding terminal in the main unit should be connected to a

grounding resistance of 100Ω or less.

•Do not drop cuttings and wire chips into the ventilation slits of the

PLC when drilling screw holes or performing wiring work.

Otherwise, fire, failure, or malfunction may occur.

6.2 Wiring example

Pin Signal name Direction Description

1 TD+ Out + side of send data

2 TD- Out - side of send data

3 RD+ In + side of receive data

4 Unused -

5 Unused -

6 RD- In - side of receive data

7 Unused -

8 Unused -

Shared grounding (good) Common grounding

(not possible)

Dedicated grounding

(best)

PLC Another

equipment PLC Another

equipment

HUB

Grounding

(100

Ω

or less)

7. Parameter Settings for FX2NC-ENET-ADP

To connect the FX2NC-ENET-ADP to the Ethernet, it is necessary to set the Ethernet

parameters, including the Header, IP address, Subnet mask, Gateway address and

TCP port number.

Set the Ethernet parameters to the 'D' data registers in the PLC.

Immediately after the power is turned on, the FX2NC-ENET-ADP reads the Ethernet

parameters stored in the 'D' data registers in the PLC, and configures itself.

7.1 Used devices

[FX1S]

Set the Ethernet parameters to nine data registers from D128 to D136.

[FX1N/FX2N/FX2NC]

Set the Ethernet parameters to nine data registers from D1000 to D1008.

If these data registers are used for any other purpose, the Ethernet parameters can be

set to nine data registers 'D' starting from D2000, D3000, D4000, D5000, D6000 or

D7000.

: Indicates any number in the range from 1 to 7.

•If "ENET" is not found or the parameters such as IP address, Gateway address,

Subnet mask are incorrect, the default parameters are valid.

•If FX2NC-ENET-ADAP cannot read out the specified data register stored in the PLC,

the default parameters are used. In such a case, the SD or RD LED is lit.

(Refer to 7.4.)

Note

*1 This is the header identifier required when FX2NC-ENET-ADP identifies the

Ethernet parameters.

Make sure to set H454E4554 ("ENET") to D128/D129 or D000/D001.

*2 The first 8 bits used for the IP address and Gateway address must be in the

range from 1 to 223.

If any number outside this range is used, the RD LED will be lit when the FX2NC-

ENET-ADP is turned on and Ethernet communication will not be performed.

*3 In the following cases (and as explained in *2) concerning the Subnet mask data,

the RD LED will be lit when the FX2NC-ENET-ADP is turned on, an error will

occur and Ethernet communication will not be performed.

(The following conditions are expressed in binary form.)

1) If 1 is set for all bits

2) If 0 is set for all bits

3) If 1 is set immediately after 0 is set

Example: 111...11000100...

*4 The settings of the IP addr ess, Subnet mask and Gateway address depend on

the network environment. For the contents of these parameters, see the network

administrator.

*5 The FX2NC-ENET-ADP searches for the header in the order "D1000 → D7000".

The values described in lowest data resister numbers are set as the Ethernet

parameters.

Data register Setting item Default

parameter Description

D128, D129 Header*1*5 - Set H454E4554 ("ENET").

D130, D131 IP address*4 192.168.0.100 Set the IP address for

connecting to Ethernet.*2

D132, D133 Subnet mask*4 255.255.255.0 Set the sub-net mask for

connecting to Ethernet.*3

D134, D135 Gateway

address*4 192.168.0.1 Set the gateway address for

connecting to Ethernet.*2

D136 TCP port

number 1024 Set the TCP ports within the

range from 1024 to 65535.

Data register Setting item Default

parameter Description

D000,D001 Header*1 - Set H454E4554 ("ENET").

D002,D003 IP address*4 192.168.0.100 Set the IP address for

connecting to Ethernet.*2

D004,D005 Subnet mask*4 255.255.255.0 Set the sub-net mask for

connecting to Ethernet.*3

D006,D007 Gateway

address*4 192.168.0.1 Set the gateway address for

connecting to Ethernet.*2

D008 TCP port

number 1024 Set the TCP ports within the

range from 1024 to 65535.

Set numbers from 1 to 223.

. . .

7.2 Parameter setting methods

Set the Ethernet parameters using either of the following methods through serial

communication:

•Setting using the PLC program

•Setting using file registers

For each setting example, refer to Section 7.3.

7.3 Parameter setting examples for FX2NC-ENET-ADP

Two examples of setting the Ethernet parameters for the FX2NC-ENET-ADP are shown

below:

Example of parameter settings

When the PLC program is used to set the Ethernet parameters

The Ethernet parameters for the FX2NC-ENET-ADP can be set using the program

shown below:

Note

In the FX2NC-ENET-ADP, the Ethernet parameters become valid only when the power

is turned ON and the setting data is stored in specified data registers.

In either of the following cases, turn off the power of the PLC once, and then turn it on

again.

•When a parameter is set for the first time

•When the setting of a parameter is changed during operation

[FX1S]

[FX1N/FX2N/FX2NC]

Data register Settin g item Parameter Set data

FX1S FX1N/FX2N/FX2NC

D128,D129 D1000,D1001 Header "ENET" H454E4554

D130,D131 D1002,D1003 IP address 192.168.0.110 HC0A8006E

D132,D133 D1004,D1005 Subnet mask 255.255.255.0 HFFFFFF00

D134,D135 D1006,D1007 Gateway

address 192.168.0.1 HC0A80001

D136 D1008 TCP port number 1024 K1024

M8002 D128H454E4554D130HC0A8006ED132HFFFFFF00D134HC0A80001MOV D136K1024

Setting of Header:

ASCII codes to specify "ENET"

Setting of Subnet mask:

255 . 255 . 255 . 0 FF FF FF 00

Setting of Gateway

address:

192 . 168 . 0 . 1 C0 A8 00 01TCP Port number:1024

D MOV

Setting of IP address

192 . 168 . 0 . 110 C0 A8 00 6EM8002 D1000H454E4554D1002HC0A8006ED1004HFFFFFF00D1006HC0A80001MOV D1008K1024

Setting of Header:

ASCII codes to specify "ENET"

Setting of Subnet mask:

255 . 255 . 255 . 0 FF FF FF 00

Setting of Gateway

address:

192 . 168 . 0 . 1 C0 A8 00 01TCP Port number:1024

D MOV

Setting of IP address

192 . 168 . 0 . 110 C0 A8 00 6E

When connecting two or more PLCs to a network, do not use the same IP

address twice.

Example: Personal computer (GX Developer)

PLC1 PLC2

192 . 168 . 0 . 10

192 . 168 . 0 . 110

192 . 168 . 0 . 111

When file registers are used to set the Ethernet parameters

Select [Parameter] - [PLC parameter] - [Memory capacity] in GX Developer, and

set the file register capacity to 1 block or more.

Then, right-click [Device memory], add the device memory data, and set the

parameters as shown below:

•Settings of D128 to D135 or D1000 to D1007 (32-bit HEX mode)

•Settings of D136 or D1008 (16-bit DEC mode)

7.4 Check of configuration using SD LED and RD LED

The SD LED and the RD LED can be used to check whether the current

configuration is functioning properly or not.

At startup (reset)

After power is turned on, the SD LED and RD LED are lit for 2 seconds, and the

FX2NC-ENET-ADP reads the configuration data from the PLC.

If the configuration data is read correctly, the SD LED and RD LED turn off. If an

error occurs, the SD LED and RD LED indicate the error status as shown below:

Note

In case of 1) or 2), the parameters such as IP address, Gateway address, Subnet

mask are incorrect and the default parameters are valid.

SD LED RD LED Description

1) ON OFF The contents of data registers in the PLC cannot be

read.

2) OFF ON

The header "ENET" cannot be detected.

A parameter such as IP address, Gateway address,

Subnet mask and TCP port number is invalid.

3) OFF OFF Valid

Header: ENET Subnet mask:

255.255.255.0 IP address: 192.168.0.110

Gateway address:

192.168.0.1 TCP port number: 1024

2NC

-ENET-ADP Ethernet adapter

USER'S MANUAL

•This manual contains text, diagrams and explanations which guide the

reader in the correct installation and operation of the FX2NC-ENET-ADP

Ethernet adapter. It should be read and understood before attempting to use

the unit.

•If in doubt at any stage of the installation of FX2NC-ENET-ADP, consult a

professional electrical technician who is qualified and trained to the local

and national standards which apply to the installation site.

•If in doubt about the operation or use of the FX2NC-ENET-ADP, please

consult the nearest Mitsubishi Electric distributor.

•This manual is subject to change without notice.

•Microsoft® and Windows® are either registered trademarks or trademarks of

Microsoft Corporation in the United States and/or other countries.

•The company name and the product name described in this manual are the

registered trademarks or trademarks of each company.

Manual Number JY997D12301

Revision D

Date May 2007