Chapter 2. Connecting 27
A/V Receiver (Stereo System)
Figure 7
Most setups require either a dig ital audio cable or stereo audi o
cables. In some circumstanc es, you may need to connect both
digital audio and stereo audio. A d igital audio cable is provided
with the TV. Stereo audio cables are not in cluded.
• To connect an analog A/V rec eiver:
Connect a set of stereo audio cables from AUDIO
OUTPUT on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
• To connect a digital A/V rec eiver with Dolby®
Digital surround soun d:
Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
*/
*/165
$0"9*"-
T
*/
*/165
$0"9*"-
$0.10/&/5
:1C1SJQQJ
*/165
47*%&0
7*%&0
"6%*0
-&'5
.0/0
"6%*0
3*()5
%57$"#-&
7)'6)'
%*(*5"-
"6%*0
065165 $BCMF$"3%
64&8*5)
"/5$"3%501
2
:
1C
1S
"6%*0
-&'5
.0/0
"6%*0
3*()5
065165
"6%*0
065165
3&$03%
065165
%7*
"OBMPH"VEJP
7*%&0
AUDIO-
LEFT/
(MONO)
"6%*0
3*()5
.0/*503-*/,)%.*
(-JOL
¸
*/165
1$'03)%.*
"/5."*/"/5"69
$0.10/&/5
:1C1S
JQQJ
*/165
47*%&0
7*%&0
"6%*0
-&'5
.0/0
"6%*0
3*()5
%57$"#-&
7)'6)'
2
:
1C
1S
"6%*0
-&'5
.0/0
"6%*0
3*()5
065165
3&$03%
065165
%7*
"OBMPH"VEJP
7*%&0
AUDIO-
LEFT/
(MONO)
"6%*0
3*()5
.0/*503-*/,)%.*
(-JOL
¸
(-JOL
¸
(-JOL
*/165
1$'03)%.*
"/5."*/
"/5"69
$BCMF$"3%
64&8*5)
"/5$"3%501
.0/*503-*/,)%.*
1$'03)%.*
"73FDFJWFS3FBS1BOFM
57#BDL1BOFM
6TFPOMZJG
DPOOFDUJOHB
%PMCZEJHJUBM
"7SFDFJWFS
Figure 7. Connecting an A/V receiver
On rare occasions, an HDMI signal may be copy-
restricted and cannot be output from the TV as a digit al
signal. To hear these copy-protected signals through the
A/V receiver, use connections for analog A /V receivers.
MP3 audio from memory ca rds cannot be connected
to digital audio. To listen to MP3 playback from the TV
memory card player through your A/ V receiver, use the
connections for an analog A/V re ceiver
Check the A/V receiver’s Owner’s Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cabl es are required. These ar e not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 S-VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO
on the TV back panel. The red cable connects to the
R (right) channel and the white cable connects to the
L (left) channel.
Note: Refer to the Satellite Receiver Owner’s Guide
for Dish Antenna connections
COMPONENT
YPbPr (480i/480p/720p/1080i)
INPUT
12
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
12
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
12VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
12
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¸
',INK¸
INPUT
PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720
COMPONENT
YPbPr
(480i/480p/720p/1080i)
INPUT
1
2
S-VIDEO
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
1
2
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
:$
-
3
-
3
7*%&0065
"6%*0065 "6%*0*/
57CBDLQBOFM
"OZ47JEFP%FWJDF
8IJUF
3FE
8IJUF
3FE
Figure 8. Connecting a Satellite Receiver with S-Vide o
Note: NetCommand® assumes you connected your
satellite receiver to Input-2. If you add a second
satellite receiver or use any other inputs for your
satellite receiver, this change must match in the
NetCommand system. See Editing NetCommand
Setup in Chapter 3 for more information.
Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video