E-3
IMPORTANT SAFETY INFORMATION
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reor ient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user’s authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
WARNING:
Unplug immediately if there is something wrong with
your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric shock.
In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inad-
vertent contact may result in an electric shock. Except
as specifically explained in the Owner’s Guide, do not
attempt to service this product yourself. Please contact
your dealer when you want to fix, adjust or inspect the
projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or drop it.
Unplug the projector and contact your dealer for inspec-
tion. It may lead to fire if you keep using the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the
lens when it is on.
Do not unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or other
trouble.
Do not touch Air outlet grille and Bottom plate which
becomes hot.
Do not touch them or put other equipment in front of Air
outlet grille. The heated Air outlet grille and Bottom plate
may cause injury or damage to other equipment. Also,
do not set the projector on the desk which is easily af-
fected by heat.
Do not look into the air outlet grille when projector
is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fire.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high hu-
midity. Please maintain an operating temperature, hu-
midity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30 and 85%
• Never put any heat-producing device under the pro-
jector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable
or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a large
current.
• Place the projector on a solid, vibration free surface:
otherwise it may fall, causing serious injury to a child
or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious
injury and damage to the projector.
• Slanting the projector more than ±10°(r ight and left)
or ±15° (front and rear) may cause trouble or explo-
sion of the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventila-
tion hole of the projector.