Stop Operation

WITHOUT STOPS

WITH STOPS

CC- This type is integral with casting, actuated by screwdriver, and require a 90° turn to open or close. When the screwdriver slot is vertical, the rubber stop is closed, and when the slot is horizontal, the rubber stop is open.

‰

7" DIA

‰

(178mm)

 

SHOWER

 

‰

 

‰

7" DIA

‰

(178mm)

 

SHOWER

 

‰

 

‰

IPS - This type has been added to the basic shower casting and is actuated by screwdriver. The stop is opened by rotating in a counterclockwise direc- tion until it stops and closed by rotating in a clockwise direction until it bot- toms.

SUPPLY ‰

‰

TUB

‰

SUPPLY

SUPPLY ‰

RUBBER STOP VALVE

(WITH SCREW DRIVER SLOT)

‰ TUB

‰

SUPPLY

‰ ‰

 

 

2" CC

 

‰

(51mm)

Rough-In

‰

2-3/16" IPS

 

 

 

(56mm)

MAKE SURE ALL WATER SUPPLIES ARE OFF.

4- port: (2700 SERIES): Install casting with "UP" at the top (arrow pointing up). If the valve is to be used for both a shower and a tub, connect the top outlet to the shower (36" minimum riser) and the bottom out- let to the tub (6" minimum drop), using 1/2" iron pipe size or 1/2" copper water tube, 5/8" O.D. (If the valve is to be used for a shower only or a tub only, plug the outlet not being used.)

3-port (2600 SERIES): These models may be used as either a shower or a tub filler. Since they are fac- tory set in the shower position, with the outlet up, you must reverse the position of the cartridge retainer clip when using the valve as a tub filler. Accomplish this change during the assembly process. Remove the stop tube, pull the clip out from the bottom of the casting, rotate cartridge stem 180° and replace clip in the top, then proceed with assembly, using 1/2" iron pipe size or 1/2" copper water tube.

WARNING: Secure all pipes and the shower and tub drop ells. Use thread seal tape on all threads. Use a plain ell on the tub drop. A twin ell is not needed. CHECK SYSTEM FOR LEAKS BEFORE CLOSING WALL.

Install Shower Arm & Tub Spout

MAKE SURE ALL WATER SUPPLIES ARE OFF.

 

 

 

2-1/8" CC

4-1/2"

 

‰

(54MM)

(114mm)

 

‰

PLASTER GROUND

 

 

3-3/4" IPS

SIZE AND WALL

 

 

 

(95MM)

 

OPENING

4-5/8" FOR C.C.

 

‰

(117mm)

‰

 

 

 

6" FOR I.P.S.

 

 

 

 

(152mm)

 

CAUTION

These valves are equipped with Moen's long-life 1225 cartridge, designed for smooth, trouble free operation. When soldering, do not heat valve any higher than neces- sary to flow the solder. Overheating may damage the cartridge or rubber stop valves. Following this direc- tion will allow you to solder without removing the cartridge or rubber stop valves.

WARNING: The cartridge and rub- ber stop valves MUST be removed before either brazing or resistance (electric) soldering. For stop valve removal instructions, see last page.

SHOWER: Install flange on long end of arm. Wrap threads on both ends of shower arm with thread seal tape.

Screw long end of shower arm into wall. Do not install showerhead prior to flushing (see Flushing).

C.C. SPOUT: The Moen Slip Fit spout is designed with an O-ring seal. It is specifically designed for installation with copper water tube. Lookout must

be free from burrs inside and out. The edge must not be rolled inward from a dull tubing cutter. The outside surface must be free from nicks and scratches.

Press and twist the spout onto the lookout upside down. Tighten the clamp screw with a 5/32" hex wrench until it just starts to bind. Turn spout upright into position against the wall and finish tightening the clamp screw by hand. The use of pliers or another wrench on the hex wrench is not necessary.

Do not overtighten.

IPS SPOUT:

C.C.

I.P.S.

CAUTION: This spout is A.B.S. plastic and will crack when in contact with some pipe thread compounds.

 

 

CLAMP SCREW

Please read the pipe compound label to be certain. We recommend using thread seal tape thread sealant.

 

 

 

 

 

 

Screw tub spout onto pipe and tighten by hand. If final turn by wrench is needed, use small wrench with smooth jaws; otherwise, pad wrench teeth with rag. Pull outward on spout while tightening to avoid scratching the wall.

DO NOT INSERT TOOL INTO SPOUT END TO TURN SPOUT.

Flushing

IMPORTANT: Before closing all wall openings, pressure test valve and complete system using flushing instructions

IMPORTANT:

Pipe chips, sand, stones, and other solids found in new or renovated plumbing can damage the sealing surface of the cartridge and cause a leak. To avoid dam- age, DO NOT TURN ON SUPPLY VALVES until instructed below:

1.Break off the protective cap on the plaster ground at the top end of the stop tube cover (see illustration page 3). Place a flat bladed screwdriver into one of the slots near a support tab and twist to break. Repeat at remaining tabs.

2.Use pliers to operate cartridge.

3.Open the cartridge in the full cold position (notched flat pointing to the right) and turn on the cold supply for 15 seconds. Without closing the cartridge, turn to the full hot position (notched flat pointing to the left) and turn on the hot supply for 15 seconds.

4.Turn the cartridge to the mixed position (notched flat pointing up), divert water to the shower and run for an additional 15 seconds.

5.Close cartridge.

6.Install showerhead.

MT662C

Page 1 Page 3
Page 2
Image 2
Moen T473, MT662C, T555, T666, T777, T888, 72700, 72615, 62700 Stop Operation, Rough-In, Install Shower Arm & Tub Spout, Flushing
Page 1 Page 3

MT662C, 72615, T555, 72700, T888 specifications

Moen is renowned for its innovative and high-quality plumbing products, and their faucet models—Moen 2291, 5401, 2290, T473, and 2700—are prime examples of this commitment to excellence. Each model features unique characteristics and cutting-edge technologies that enhance functionality and aesthetics in contemporary kitchens and bathrooms.

The Moen 2291 is a stylish and practical kitchen faucet characterized by its sleek, high-arc design. It features Moen's Duralast cartridge, which ensures smooth operation and longevity, minimizing the need for repairs. The faucet includes a pull-down sprayer with a powerful spray mode and a pause function, allowing for easy rinsing and cleaning. This model also comes with Spot Resist stainless finish, reducing water spots and fingerprints, ensuring that it remains attractive with minimal maintenance.

The Moen 5401 is a premier choice for those who value both style and performance in a kitchen faucet. Its unique design includes a side spray that complements the primary faucet, providing versatility in washing dishes and cleaning the sink. The 5401 is equipped with Moen's Reflex System, allowing for easy pull-down and retract functions, enhancing the user experience. The chrome finish of this model adds a touch of elegance, making it a perfect addition to any kitchen décor.

For those seeking a minimalist design, the Moen 2290 is an excellent option. This two-handle faucet combines vintage charm with modern functionality. Its high-quality construction and durable materials ensure resilience over time. The 2290 incorporates the innovative Posi-Temp pressure-balancing control, which maintains water temperature, preventing sudden changes that can be uncomfortable during use.

The Moen T473 showcases the brand's commitment to style and ease of use with its sleek design and advanced features. This model includes Moen's powerful Power Clean technology, providing 50% more spray power than most pull-down and pull-out faucets. This means quicker and more effective cleaning, all while maintaining a steady water flow.

Lastly, the Moen 2700 is designed specifically for bathrooms, offering a traditional and elegant touch. Its single-handle operation allows for easy temperature and flow control. The Eco-Performance feature of the 2700 reduces water consumption without sacrificing performance, making it an eco-friendly choice for water-conscious consumers.

Collectively, these Moen models offer a range of designs suited for various preferences while incorporating groundbreaking technologies and thoughtful features that elevate the overall user experience in any setting.
Top Page Image Contents