5. TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
Power/ Status Light MessagesCondition | Power Indicator | Status Indicator | Note |
Standby | Steady orange | – | – |
|
|
|
|
Cooling down | Blinking green | – | Blinks green for 60 seconds |
|
|
|
|
Lamp in | Steady green | – | – |
|
|
|
|
Lamp in Eco mode | Steady green | Steady green | – |
|
|
|
|
3 minutes after lamp is turned on in | Steady green | Blinking green | Fixed at |
Eco mode |
|
| can be changed on the menu |
|
|
|
|
Lamp has reached its end of life | Steady green | Steady red | Message appears on screen during 1500- |
(1500 hours or over) |
| Steady orange (Eco mode) | 1600 hours of lamp usage. The projector |
|
|
| reaches its end of life. Please replace the |
|
|
| lamp as soon as possible. |
|
|
|
|
Lamp life has reached its end of life | Steady orange | Steady red | The projector is in standby mode and can- |
(1600 hours or over) |
|
| not be turned on. |
|
|
|
|
Lamp or filter cover error (3 locations) | Steady orange | Blinking red (1 sec interval) | The projector is in standby mode and can- |
|
|
| not be turned on. |
|
|
|
|
Temperature error | Steady orange | Blinking red (4 sec interval) | The projector is in standby mode and can- |
|
|
| not be turned on. |
|
|
|
|
Fan error | Steady orange | Blinking red (8 sec interval) | The projector is in standby mode and can- |
|
|
| not be turned on. |
|
|
|
|
Lamp error | Steady orange | Blinking red (12 sec interval) | The projector is in standby mode and can- |
|
|
| not be turned on. |
|
|
|
|
Problem | Check These Items | |
Does not turn on | • | Check that the power cable is plugged in and that the power button on the projector cabinet or the remote |
|
| control is on. |
| • Ensure that the lamp cover is installed correctly. See page | |
| • | Check to see if the projector has overheated or the lamp usage exceeds 1600 hours (2600 hours in Eco |
|
| mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is particu- |
|
| larly warm, move the projector to a cooler location. |
No picture | • | Use the menu to select your source (Video, |
| • Ensure your cables are connected properly. | |
| • Use menus to adjust the brightness and contrast. See page | |
| • Remove the lens cap. | |
| • | Reset the settings or adjustments to factory preset levels using the Factory Default on the Image Options |
|
| Menu in Advanced menu. See page |
Image isn’t square to the | • | Reposition the projector to improve its angle to the screen. See page |
screen | • | Use the Keystone to correct the trapezoid distortion. See page |
|
|
|
Picture is blurred | • | Adjust the focus. See page |
| • Reposition the projector to improve its angle to the screen. See page | |
| • Ensure that the distance between the projector and screen is within the adjustment range of the lens. See | |
|
| page |
|
|
|
Image is scrolling vertically, | • | Use menus or a source button on the remote control or the cabinet to select the source you want to input. |
horizontally or both |
|
|
Remote control does not | • | Install new batteries. See page |
work | • | Make sure there are no obstacles between you and the projector. |
| • Stand within 22 feet (7 m) of the projector. See page | |
| • Make sure that you are in the Projector mode or the PJ button lights in red. If not, press the PJ button. | |
|
|
|
Status indicator is lit or blink- | • | See the Power/ Status Light messages above. |
ing |
|
|
|
|
|
Cross color in RGB mode | • | If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image with the Position and Clock |
|
| Adjust on the Advanced Options Menu. See page |
|
|
|
E – 49