Setup menus

SYSTEM menu

<SYSTEM>

 

Item

 

Setting

 

 

 

 

 

 

 

 

 

Description

No.

Superimposed

No.

 

Superimposed

display

 

 

display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

00

WFM SEL

0000

 

 

 

CTL

This selects the signal to output from the VIDEO OUT 2

 

 

0001

 

 

 

TC

connector.

 

 

0002

 

 

 

VIDEO

 

0: The CTL signal is output.

 

 

0003

 

 

 

SYNC

1: The TIME CODE signal is output.

 

 

0004

 

 

 

RF-L

2: The VIDEO OUT signal is output.

 

 

0005

 

 

 

RF-R

3: The SYNC signal is output.

 

 

0006

 

 

 

ENV-L

4: The PB L RF signal is output.

 

 

0007

 

 

 

ENV-R

5: The PB R RF signal is output.

 

 

 

 

 

 

 

 

6: The PB L ENV signal is output.

 

 

 

 

 

 

 

 

7: The PB R ENV signal is output.

 

 

 

 

 

 

 

 

<Note>

 

 

 

 

 

 

 

 

1. The settings can be changed at any time regardless of the

 

 

 

 

 

 

 

 

setup menu item No. 30 (MENU LOCK) setting.

 

 

 

 

 

 

 

 

2. The signals which are output during normal playback have

 

 

 

 

 

 

 

 

approximately the levels given below.

 

 

 

 

 

 

 

 

CTL: 0.1 to 0.3 Vp-p TC: 0.6 Vp-p

 

 

 

 

 

 

 

 

VIDEO: 1.0 Vp-p

 

 

 

 

 

 

 

 

 

10

ENCODER

0000

 

 

 

REMOTE

This selects whether the video output signal is to be adjusted

 

REMOTE

0001

 

 

 

LOCAL

on the VTR or with the external encoder remote control.

 

SEL

 

 

 

 

 

 

0: Video output signals are adjusted with the external encoder

 

 

 

 

 

 

 

 

remote control.

 

 

 

 

 

 

 

 

1: Video output signals are adjusted on the VTR.

 

 

 

 

 

 

 

 

11

SYS SC/H

0000

 

 

 

REMOTE

This sets whether the system phase is to be adjusted using

 

 

0001

 

 

 

LOCAL

the unit’s controls or using the external encoder remote

 

 

 

 

 

 

 

 

control.

 

 

 

 

 

 

 

 

0: The external encoder remote control is used to adjust the

 

 

 

 

 

 

 

 

system phase.

 

 

 

 

 

 

 

 

1: The system phase is adjusted using the unit’s controls.

 

 

 

 

 

 

 

 

<Note>

 

 

 

 

 

 

 

 

This setting has no effect when LOCAL has been selected as

 

 

 

 

 

 

 

 

the SYSTEM menu item No.10 (ENCODER SEL).

 

 

 

 

 

 

 

 

12

SYS H

0000

 

 

 

–1100

This enables the system phase to be adjusted in 13.5ns steps.

 

(HD)*1

:

 

:

 

-: The phase is advanced.

 

 

1100

 

 

0

 

+: The phase is delayed.

 

 

:

 

:

 

<Note>

 

 

2200

 

1100

 

If setting operation is performed, the setting value does not

 

 

 

 

 

 

 

 

return to factory (default) setting.

 

 

 

 

 

 

 

 

13

V PHASE

0000

 

 

 

–500

This enables the video system phase to be adjusted in 27ns

 

(HD)*1

:

 

:

 

steps.

 

 

0500

 

 

0

 

-: The phase is advanced.

 

 

:

 

:

 

+: The phase is delayed.

 

 

1000

 

500

 

<Note>

 

 

 

 

 

 

 

 

In the case of the HD up-converter output from the SD

 

 

 

 

 

 

 

 

playback tape (when the option has been installed), the video

 

 

 

 

 

 

 

 

phase is fixed.

 

 

 

 

 

 

 

 

14

SYS SC

0000

 

 

 

–108

This enables the system phase to be adjusted in a total

 

(SD)*2

:

 

:

 

variable range of +/-180 degrees or more.

 

 

0108

 

0

 

-: The phase is advanced.

 

 

:

 

 

:

 

+: The phase is delayed.

 

 

0216

 

108

 

<Note>

 

 

 

 

 

 

 

 

If setting operation is performed, the setting value does not

 

 

 

 

 

 

 

 

return to factory (default) setting.

 

 

 

 

 

 

 

 

 

The underline on the setting item denotes the initial setting.

*1: With the HD output (HD tape playback or up-conversion output)

*2: With the SD output (SD tape playback or down-conversion output)

– 51 –