Technical Information
6) Then use [Lens shift] to overlap the shaded areas.
zzThe red line will turn yellow if it is overlapped correctly.
Edge blending |
| On |
Left | Start |
|
| Width |
|
Right | Start |
|
| Width |
|
Top | Start |
|
| Width |
|
Bottom | Start |
|
| Width |
|
|
|
|
Black level | All | All |
Test pattern |
| On |
Menu off |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Reset | Back | |||
|
|
|
|
|
|
|
|
|
|
|
| Exit | Back | Move | Next | ||||||
Edge blending |
| On |
Left | Start |
|
| Width |
|
Right | Start |
|
| Width |
|
Top | Start |
|
| Width |
|
Bottom | Start |
|
| Width |
|
|
|
|
Black level | All | All |
Test pattern |
| On |
Menu off |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Reset | Back | |||
|
|
|
|
|
|
|
|
|
|
|
| Exit | Back | Move | Next | ||||||
Line (yellow) | Frame (green): Projected image |
7) Turn [Test pattern] to [On] to display a 50% white test pattern.
zzThe overlapping areas will be displayed more brightly than other areas.
8) Adjust [Black level] so that there is no difference between the overlapping areas and other areas.
zzTo adjust the overlapping areas, setting a smaller value to the [Contrast] in the [Image adjust] menu is recommended.
If the left and right colors do not match, proceed to the following step.
■■[Color matching]
9)Select [Color matching] in the [Setting] menu and display the setting screen.
10)Turn on color matching with [On] and adjust [Red]/[Green]/[Blue]/[White].
11)Select [Advanced color matching] if more detailed settings are required, and display the setting screen.
12)Turn on advanced color matching with [On] and adjust each color with [Target].
zzSet the [Target] value to within the [Measured] value range.
| $GYDQFHGFRORUPDWFKLQJ |
| 2Q |
| |
|
|
|
| ||
0HDVXUHG |
|
| ,QIRUPDWLRQ | ||
|
| 5HG |
|
|
|
|
| *UHHQ |
|
|
|
|
| %OXH |
|
|
|
|
|
|
|
| |
7DUJHW | 5HG |
|
|
| |
|
| *UHHQ |
|
|
|
|
| %OXH |
|
|
|
|
| &\DQ |
|
|
|
|
| 0DJHQWD |
|
|
|
|
| <HOORZ |
|
|
|
|
| :KLWH |
|
|
|
$XWRWHVWSDWWHUQ |
|
|
|
|
|
|
|
|
|
| 2II |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 0HQXRII |
|
|
|
| 7HVWSDWWHUQ |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| )DFWRU\GHIDXOW |
| 6WRUH |
|
| 5HVHW |
| %DFN |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ([LW | %DFN | 0RYH |
|
| 1H[W | ||||||||
Example) Value for “[Red], x”
“[Measured] = 0.674”, so [Target] is set to a smaller value of “0.650”.
13)If the colors do not match even after adjusting [Target], use a colorimeter to measure the chromaticity coordinates and luminance to make further adjustments.
Appendix
102 - ENGLISH