“NODEVICE” “NO DEVICE”

•You cannot do recording or check available storage space because there is no USB device connected to

USB B .

“NO DISC”

•You have not put in a disc.

•You have not put in the disc correctly. Put it in correctly. (Z10)

“NO MP3”

• Select an MP3 content before recording can start.

“NO PLAY”

“UNSUPPORT”

•Examine the content. You can only play supported format. (Z22)

•The files in the USB device can be corrupted. Format the USB device and try again.

•The system may have a problem. Switch off the system and then switch on again.

•You put in a disc that the system cannot play. Change to a playable disc. (Z22)

•You put in a blank disc.

•You put in a disc that has not been finalised.

“NO TRACK”

• There is no MP3 file in the USB device.

“PLAYERROR”

•You played an unsupported MP3 file. The system will skip that track and play the next one.

“REC ERROR”

•You disconnected the USB device while recording. Connect the USB device and do recording again. (Z10, 17)

•Error occurred during USB recording. Disconnect the USB device and then connect again. (Z10, 17)

“REMOTE 1” “REMOTE 2”

•The remote control and the main unit are using different codes. Change the code of the remote control. (Z27)

−When “REMOTE 1” is shown, press and hold [OK] and [1] for a minimum of 4 seconds.

−When “REMOTE 2” is shown, press and hold [OK] and [2] for a minimum of 4 seconds.

“TEMP NG”

•The temperature protection circuit has been activated, and the system will switch off. Let the unit cool down before switching it on again.

•Check that the ventilation opening of the unit is not obstructed.

•Ensure this unit is well ventilated.

“USB OVER CURRENT ERROR”

•The USB device is using too much power. Disconnect the USB device, switch off the system and then switch on again.

“VBR”

•The system cannot show the remaining play time for variable bit rate (VBR) tracks.

█TV displays

“THIS DISC CANNOT BE PLAYED IN YOUR REGION.”

•You can only play DVD-Video if the region code is compatible with this system. You can check the compatible region code at the rear of the main unit. (ZCover page)

“”

• The operation is prevented by the system or disc.

“THIS TYPE OF DEVICE CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DEVICE.”

•Make sure there is video or picture content in the USB device.

█Picture

Picture is distorted.

•It is common to experience some distortion during “SEARCH”.

•Make sure that the system is connected directly to the TV, and is not connected through a VCR. (Z7)

• Change the “SOURCE SELECT” in Menu 2. (Z15)

No picture.

•Examine the connection. (Z7)

•Make sure that the video input mode of the TV is correct. (Z7)

A defective TV display or faded colours.

•The system and TV are using different video systems.

For Southeast Asia

−Use the multi-system or NTSC TV.

For the Middle East and South Africa

−Use the multi-system or PAL TV.

•The system used on the disc does not complement your TV.

−Videos on PAL discs cannot be correctly shown on an NTSC TV.

−This system can convert NTSC signals to PAL 60 to be shown on a PAL TV (“NTSC DISC OUT” in “VIDEO” menu). (Z21)

Picture stops.

• Picture can stop if the Xvid contents are more than 2 GB.

Menus not shown correctly.

•Change the zoom ratio to “NORMAL” in “ZOOM” in Menu 2. (Z15)

•Change the “TV ASPECT” in “VIDEO” menu. (Z21)

Auto zoom function does not operate correctly.

•Switch off the zoom function of the TV.

•Use the other preset aspect ratios or manual adjustment. (Z21)

•Zoom function does not work well especially in dark scenes or does not work at all due to the type of disc.

RQT9952

26