Panasonic WV-CP240, WV-CP242, WV-CP244 manual

(Lens Option)

Color CCTV Cameras

Operating Instructions

Model No. WV-CP240

WV-CP242

WV-CP244

Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.

7.Do not operate the camera beyond the specified temperature, humidity or power source ratings.

Use the camera under conditions where tem- perature is between –10°C - +50°C (14°F - 122°F), and humidity is below 90 %. The input power source is 120 V AC 60 Hz for WV-CP240, 12 V DC for WV-CP242, and 24 V AC 60 Hz for WV-CP244.

Caution:

To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

CONNECTIONS

A. WV-CP240 (120V AC 60Hz)Connect the power cord to an electrical outlet of 120V AC 60Hz.B. WV-CP242 (12V DC)

Connect the power cord to the DC 12V IN terminal on the rear panel of the WV-CP242.

Installation of Auto Iris Lens

Connector

Install the lens connector (YFE4191J100) when using a video drive ALC lens.

The installation should be made by qualified service personnel or system installers.

Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover of the supplied connector as shown in the diagram.

The pin assignment of the lens connector is as fol- lows:Pin 1: Power source; +9 V DC, 50 mA max.Pin 2: Not usedPin 3: Video signal; 0.7 V[p-p]/40 kΩPin 4: Shield, ground

SPECIFICATIONS

Pick-up Device:	768 (H) x 494 (V) pixels, Interline Transfer CCD
Scanning Area:	4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3”
	pick-up tube)
Synchronization:	Internal, Line-locked or Multiplexed vertical drive (VD2),
	selectable
Scanning System:	2 : 1 interlace
Scanning:	525 lines / 60 fields / 30 frames
Horizontal:	15.734 kHz
Vertical:	59.94 Hz
Horizontal Resolution:	480 lines
Video Output:	1.0 V[p-p] NTSC composite 75 Ω / BNC connector
Signal-to-Noise Ratio:	50 dB (Equivalent to AGC Off, weight On)
Electronic Light Control:	Equivalent to continuous variable shutter speed between 1/60 s
	and 1/15 000 s
Minimum Illumination:	0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-
	candle) at F1.4] AGC On
Detail:	SHARP or SOFT, selectable

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

12 V DC

Rib

Pin 3

Lens Mount:	C-mount or CS-mount, selectable
Ambient Operating Temperature:	−10°C - +50°C (14°F - 122°F)

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

<WV-CP240>

(10.5 V - 16 V)

Resistance of copper wire [at 20°C (68°F)]

Pin 1

Pin 4

Ambient Operating Humidity:	Less than 90 %
Power Source and	WV-CP240:	120 V AC 60 Hz, 3.6 W
Power Consumption:	WV-CP242:	12 V DC, 270 mA
	WV-CP244:	24 V AC 60 Hz, 3.3 W

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral trian- gle, is intended to alert the user to the presence of uninsulated "dan- gerous voltage" within the product's enclosure that may be of sufficient

SA 1965 magnitude to constitute a risk of electric shock to persons.

N0301-3043 V8QA5733DN	Printed in Japan
	N 19

For U.S.A

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ- ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manu- al, may cause harmful interference to radio com- munications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on the bottom of the unit.

			ALC BLC ON
ALC BLC ON			VIDEO SHARP	INT
VIDEO OUT		INT	VIDEO SHARP	INT
VIDEO SHARP		INT			LOCK
					LOCK
DC	SOFT	LL
ELC	OFF

<WV-CP244>				DC	SOFT LL
				ELC	OFF
AC 24V IN			GND
			GND
					WV–CP244
1	2
	ALC	BLC ON
	VIDEO SHARP		INT
VIDEO OUT
	DC	SOFT	LL
	ELC	OFF
<WV-CP242>				ALC	BLC ON
				VIDEO SHARP
DC 12V IN
					Camera Mounting	Fixing Screws
					Screw Holes
	ALC BLC ON			DC	SOFT
	VIDEO	SHARP		ELC	OFF
VIDEO OUT				ELC	OFF	Mount Adapter
	DC	SOFT	OFF			Mount Adapter
	ELC		OFF
						c
						cs

Copper wire	#24	#22	#20	#18
size (AWG)	(0.22mm2)	(0.33mm2)	(0.52mm2)	(0.83mm2)

Resistance	0.078	0.050	0.03.	0.018
Ω/m	0.078	0.050	0.03.	0.018
Ω/m

Resistance	0.026	0.017	0.010	0.006
Ω/ft	0.026	0.017	0.010	0.006
Ω/ft

•Calculation of maximum cable length between camera and power supply :10.5V DC ≤ VA − (R x 0.42 x L) ≤ 16V DCL : Cable length (meters)R : Resistance of copper wire (Ω/meter)VA : DC output voltage of power supply unit

		VA − 12
L standard =			(meters)

		0.42 x R
		VA − 16
L minimum =			(meters)
		0.42 x R
	VA − 10.5
L maximum =			(meters)

0.42x R

C.WV-CP244 (24V AC 60Hz)

Connect the power cable to the AC 24 V IN terminal on the rear panel of the WV-CP244.

Pin 2

Solder the lens cable to the pins of the supplied connector.

Mounting the Lens

Caution:

Before you mount the lens, loosen the screw on the side of the camera, and rotate the flange-back adjusting ring clockwise until it stops. If the ring is not at the end, the inner lens or CCD image sensor may be damaged.

qMount the lens by turning it clockwise on the lens mount of the camera.

wConnect the lens cable to the auto iris lens connector on the side of the camera.

Focus Fixing Screw

Dimensions (without lens):	67 mm (W) x 65 mm (H) x 123 mm (D)
	2-5/8” (W) x 2-9/16” (H) x 4-13/16” (D)
Weights (without lens):	WV-CP240:	0.48 kg (1.06 lbs)
	WV-CP242:	0.3 kg (0.66 lbs)
	WV-CP244:	0.33 kg (0.73 lbs)

Weights and dimensions indicated are approximate.Specifications are subject to change without notice.

STANDARD ACCESSORIES

Body Cap............................................................................................	1 pc.
ALC Lens Connector (YFE4191J100).................................................	1 pc.

OPTIONAL ACCESSORIES

Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,

	The exclamation point within an
	equilateral triangle is intended to
	alert the user to the presence of
	important operating and mainte-
	nance (servicing) instructions in the
	literature accompanying the appli-
SA 1966	ance.
SA 1966

You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

qAuto Iris Lens ConnectorSupplies power and control signals to an auto iris lens (not supplied).

w Flange-back Adjusting Ring

This ring adjusts the back-focal distance or

ON: Select this mode when a strong light such as a spotlight is in the background.

OFF: Normal picture.!1 Detail/Aperture Level Selector (SHARP,SOFT)

1 2

WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3, WV-LFY45C3, WV-LFY9C3

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

PREFACE

Panasonic’s WV-CP240/CP242/CP244 series digi-	transfer CCD image sensor having 768 horizontal
tal signal processing color CCD cameras intro-	pixels (picture elements), and digital signal pro-
duce a new level of high picture quality and high	cessing LSI’s. This model offers cutting-edge
resolution through the use of a 1/3-inch interline	technology for advanced video surveillance.

FEATURES

1. The following functions are built in.	2. Minimum illumination of 0.6 lx (0.06 foot-can-
(1) Auto Light Control (ALC)/Electronic Light	dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-

picture focus. Rotate this ring clockwise for a

C-mount lens or counterclockwise for a CS-

mount lens.

eLens (option)rMount Adapter

The camera mounting screw hole is for mounting the camera onto a mounting brack- et. The camera is originally designed to be mounted from the bottom, however, a top- mounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop.

The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor.

SHARP: Normal position.SOFT: Select this position when a QuadSystem is connected to this camera.!2 Automatic Light Control/Electronic LightControl Selector (ALC, ELC)Lets you select the mode according to the lens type used.

ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera.

ELC: Select this mode when a fixed iris lens or manual iris lens is used with this cam- era.

!3 Lens Drive Signal Selector (VIDEO, DC)

Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens con- nector.

24 V AC, 60 Hz

(19.5 V - 28 V)

Recommended wire gauge sizes for 24 V AC line

Copper wire		#24	#22	#20	#18
size (AWG)		(0.22mm2)	(0.33mm2)	(0.52mm2)	(0.83mm2)

Length	(m)	95	150	255	425
of Cable
of Cable
(Approx.)	(ft)	314	495	842	1 403

Caution:

To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

Video Cable

Caution for Mounting the Lens

The lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter.

The protrusion at the rear of the lens should be as shown in the diagram.

	Control (ELC)		candle) at F1.4)
(2)	Automatic Gain Control (AGC) +15 dB
	and Automatic Tracing White Balance	3.	Signal-to-noise ratio of 50 dB
	(ATW)		(Equivalent to AGC Off)
(3)	Camera synchronization mode selec-
	table between internal (INT), Line-locked	4.	Horizontal resolution of 480 lines
	(LL) for WV-CP240 and WV-CP244 and
	Multiplexed Vertical Drive (VD2).	5.	Auto iris lens control selectable between
			video signal and DC power supply.

PRECAUTIONS

tFocus Fixing ScrewyPower Cord (only for WV-CP240)Connect this power cord to an electrical out- let of 120 V AC 60 Hz.uDC 12 V Input Terminal[DC 12V IN (only for WV-CP242)]This terminal is for connecting the 12 V DC power supply cord.

i AC 24 V Input Terminal

[AC 24V IN (only for WV-CP244)]

This terminal is for connecting the 24 V AC

VIDEO: Select this mode if you are using a auto iris lens that requires a video drive signal.

DC: Select this mode if you are using a auto iris lens that requires a DC drive signal.

!4 Video Output Connector (VIDEO OUT)

This connector is for connecting with the VIDEO IN connector of the video monitor. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the camera synchronization mode is automatically set to Vertical Drive.

1. It is recommended to use a monitor whose

C-mount: Less than 13 mm (1/2”)

resolution is at least equal to that of theCS-mount: Less than 8 mm (5/16”) camera.

2.The maximum extensible coaxial cable length between the camera and the moni- tor is shown below.

Type of		RG-59/U	RG-6U	RG-11/U	RG-15/U
coaxial cable		(3C-2V)	(5C-2V)	(7C-2V)	(10C-2V)

Recommended	(m)	250	500	600	800
maximum
maximum
cable length	(ft)	825	1 650	1 980	2 640

1.Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers.

There are no user serviceable parts inside. Ask a qualified service person for servicing.

2.Handle the camera with care.

Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.

3.Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.

4.Do not use strong or abrasive detergents when cleaning the camera body.Use a dry cloth to clean the camera when dirty.

In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remained part of the detergent in it with a dry cloth.

5.Clean the CCD faceplate with care.

Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol.

6.Never face the camera towards the sun. Do not aim the camera at bright objects.

60Hz power supply cord.

oSynchronization Mode Selector [INT, LL (only for WV-CP240 and WV- CP244)]

Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL).

INT: Sets to internal 2:1 interlace.LL: Sets to Line-lock mode.!0 Back Light Compensation Mode Selector (BLC ON, OFF)

Lets you select the mode according to the position of the object and light conditions on the screen.

Cautions:

•Connect to 12 V DC (10.5 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is sup- plied from a 24 V AC power source.

•To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

FOCUS OR FLANGE-BACK ADJUSTMENT

The following adjustment should be made by			w Turn the flange-back adjusting ring to the
qualified service personnel or system installers.			desired position.
q Loosen the screw on the side of the camera.			Caution: When the C-mount lens is mounted,
			do not rotate the ring counterclockwise
Focusing of	Focusing of		by force after it stops. If the ring is rotat-
CS-mount lens	C-mount lens		ed by force, the inner lens or CCD image
			sensor may be damaged.
			e Tighten the screw on the side of the camera.
			Caution: Tightening the screw by force will
	LOCK	Focus Fixing Screw	cause damage to the screw or deviation
		Flange-back	of focus.
		Adjusting Ring

	Panasonic Digital Communications & Security Company	PANASONIC CANADA INC.
	Unit of Matsushita Electric Corporation of America	5770 Ambler Drive, Mississauga,
	Security Systems Group	Ontario, L4W 2T3 Canada (905)624-5010
	Security Systems Group	PANASONIC SALES COMPANY
	www.panasonic.com/cctv	PANASONIC SALES COMPANY
	www.panasonic.com/cctv	DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
	Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094	DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
		San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
	Zone Office
	Zone Office	P.R. 00985 (809)750-4300
	Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303	P.R. 00985 (809)750-4300

	Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
	Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840