Paradyne 3162 E-6

SNMP MIB Objects

E-6 3162-A2-GB20-30March 1999

Interface Group – “ifOperStatus” Object (ifEntry 8)

This object specifies the current operational state of the interface. The value of

this object for each interface is defined as follows:

Network T1: The interface is up(1) when no alarm conditions exist.

The interface is down(2) when an alarm condition is active.

The interface is testing(3) when a test is active on the

interface.

DTE T1: The interface is up(1) when no alarm conditions exist and

the interface is enabled.

The interface is down(2) when an alarm condition is active

and the interface is disabled.

The interface is testing(3) when a test is active on the

interface.

COM Port: When configured as an SNMP management link, up and

down are based on the current state of the link layer

protocol. Otherwise, the interface is always up(1).

The interface is never in the testing(3) state.

AUX Port: When configured as an SNMP management link, up and

down are based on the current state of the link layer

protocol. Otherwise, the interface is always down(2).

The interface is never in the testing(3) state.

Data Ports: The interface is up(1) when the port is assigned to a T1

interface or another data port as a backup, and both CTS

and DSR are ON.

The interface is down(2) when the port is unassigned, or

either CTS or DSR is OFF.

The interface is testing(3) when a test is active on the

interface.

Interface Group – “ifLastChange” Object (ifEntry 9)

This object contains the value of “sysUpTime” at the time the interface entered its

current operational state.

Contents

Main Page B !Important Safety Instructions Page D Government Requirements and Equipment Return United States NOTICE TO USERS OF THE UNITED STATES TELEPHONE NETWORK DSU/CSU Facility Interface Codes Code Description Caution: i Contents About This Guide 1 Introduction 2 Installation ii 3 Operation iii 4 Monitoring and Testing iv A Asynchronous Terminal Menu B Technical Specifications C Configuration Options D Pin Assignments v E SNMP MIB Objects F IP Network Addressing Scenario G Equipment List Glossary Index Page vii About This Guide Document Purpose and Intended Audience Document Summary Section Description viii Product-Related Documents Document Number Document Title Reference Documents 1-1 Introduction 1 Features 1-2 DTE Drop/Insert (DSX-1) Interface Operation Asynchronous Terminal Interface Support Alarm Message Capability Telnet Access Physical Description Test Jacks Operation Front Panel LEDs 1-4 2-1 Installation 2 Application Examples 2-2 NETWORK SERVICES Figure 2-3. Fractional T1 Application Example Figure 2-2. Shared Access Application Example FRACTIONAL NETWORK SNMP or Telnet Connection Examples NETWORK 2-4 NETWORK Figure 2-8. Remote Access through FDL/EDL NETWORK Figure 2-6. Connection through a LAN Adapter Important Instructions Figure 2-9. Cabling Examples Pin Assignments Important Safety Instructions section at the beginning of this guide. Power-Up Self-Test Self-Test Results Maintenance 3-1 Operation 3 Menu Organization Front Panel LEDs 3-2 Table 3-1. System LEDs Table 3-2. Network Interface LEDs 3-3 Table 3-3. DTE Drop/Insert (DSX-1) Interface LEDs 3-4 Table 3-4. Data Port LEDs 3-5 Initiating an Asynchronous Terminal Session Entering a Password to Gain Access Ending an Asynchronous Terminal Session 3-6 Recovering Asynchronous Terminal Operation 3-7 3162-A2-GB20-30 March 1999 Menu Organization Figure 3-3. Menu Organization Figure 3-3 shows the organization of the asynchronous terminal menu tree. 3-8 Using Asynchronous Terminal Screens 3-9 3-10 Setting Customer Identification 3-11 Displaying LED Conditions 3-12 Changing Configuration Options 3-13 Displaying or Editing Configuration Options 3-14 Figure 3-7. Configuration Edit/Display Screen 3-15 Saving Edit Changes 3-16 Configuring the DSU/CSU for SNMP or Telnet Access Configuration Examples 3-17 Selecting the Port 3-18 Setting the IP Address xxx.xxx.xxx.xxx IP Network Addressing Scenario 3-19 Selecting the Link Layer Protocol Setting the IP Address Selecting the Port 3-20 Configuring DS0 Channels 3-21 Figure 3-10. Example of Channel Allocation 3-22 Network Interface Network Channel Allocation Figure 3-11. Example of Network Interface Worksheet 3-23 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation Figure 3-12. Example of DTE Drop/Insert Interface Worksheet 3-24 Displaying DS0 Channel Assignments 3-25 3-26 Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface 3-27 Configuring DS0 Channels for Robbed Bit Signaling 3-28 Allocating Data Ports Using the Block or ACAMI Assignment Method n 3-29 Allocating Data Ports Using the Individual Channel Assignment Method Clearing DS0 Channel Allocation 3-30 Establishing Access Security on a Port Setting a Password 3-31 Setting a Password Establishing Access Security on a Port 3-32 Entering a Password to Gain Access If an invalid password is entered three consecutive times If the password is invalid If the password is valid Selecting the Timing Source 3-34 Providing Backup Capability Download Operations 4-1 Monitoring and Testing 4 Installation Self-Test Results 4-2 Table 4-1. Self-Test Results xxxxxxxx 4-3 Device Health and Status To display health and status messages: 4-4 Performance Reports 4-5 To display performance reports: 4-6 Table 4-3. Performance Registers (2 of 3) Register Totals DescriptionInterval Description 4-7 Table 4-3. Performance Registers (3 of 3) Register Totals DescriptionInterval Description 4-8 Alarms 4-9 Alarm and Trap Troubleshooting SNMP Traps 4-10 4-11 Troubleshooting 4-12 Table 4-6. Troubleshooting (2 of 2) Symptom SolutionsPossible Cause 4-13 Test Jacks 4-14 Test Commands 4-15 Remote Loopback Tests For Networks For Channels Sending a Line Loopback Up or Down 4-16 Local Loopback Tests 4-17 Starting a Line Loopback 4-18 Starting a Payload Loopback Starting a DTE Loopback 4-19 Starting a Repeater Loopback 4-20 Starting a Data Channel Loopback 4-21 Starting a Data Terminal Loopback Aborting Loopbacks 4-22 Test Patterns Sending Network QRSS or Network 1-in-8 Test Patterns Page Lamp Test 4-25 Displaying DSU/CSU Test Status To display test status: 2. From the Status screen, select System and Test Status. Table 4-10. Test Status Messages Page A-1 Asynchronous Terminal Menu A Page B-1 Technical Specifications B Technical Specifications B-2 Table B-1. Model 3162 DSU/CSU Technical Specifications (2 of 2) Specifications Criteria C-1 Configuration Options C C-2 Network Interface Configuration Options Table C-1. Network Interface Configuration Options (1 of 3) C-3 Table C-1. Network Interface Configuration Options (2 of 3) C-4 Table C-1. Network Interface Configuration Options (3 of 3) DTE Interface Configuration Options Table C-2. DTE Interface Configuration Options (1 of 2) C-5 Table C-2. DTE Interface Configuration Options (2 of 2) C-6 Sync Data Port Configuration Options Table C-3. Sync Data Port Configuration Options (1 of 5) C-7 Table C-3. Sync Data Port Configuration Options (2 of 5) C-8 Table C-3. Sync Data Port Configuration Options (3 of 5) C-9 Table C-3. Sync Data Port Configuration Options (4 of 5) C-10 Table C-3. Sync Data Port Configuration Options (5 of 5) C-11 Cross Connect Configuration Options DTE-to-Network Assignment Options Table C-4. DTE-to-Network Assignment Options C-12 Sync Data Port Assignment Options Table C-5. Sync Data Port Assignment Options (1 of 3) C-13 Table C-5. Sync Data Port Assignment Options (2 of 3) OR C-14 Table C-5. Sync Data Port Assignment Options (3 of 3) C-15 General Configuration Options Table C-6. General Configuration Options (1 of 2) C-16 Table C-6. General Configuration Options (2 of 2) C-17 User Interface Configuration Options Communication Port Configuration Options C-18 Table C-7. Communication Port Configuration Options (2 of 3) C-19 Table C-7. Communication Port Configuration Options (3 of 3) External Device Configuration Options Table C-8. External Device Configuration Options (1 of 3) C-20 Table C-8. External Device Configuration Options (2 of 3) C-21 Table C-8. External Device Configuration Options (3 of 3) X.X C-22 Telnet Sessions Configuration Options Table C-9. Telnet Sessions Configuration Options C-23 Auxiliary Port Configuration Options Table C-10. Auxiliary Port Configuration Options C-24 Alarm and Trap Configuration Options Table C-11. Alarm and Trap Configuration Options (1 of 2) C-25 Table C-11. Alarm and Trap Configuration Options (2 of 2) C-26 Management and Communication Configuration Options Communication Protocol Configuration Options C-27 Table C-12. Communication Protocol Configuration Options (2 of 3) C-28 Table C-12. Communication Protocol Configuration Options (3 of 3) C-29 General SNMP Management Configuration Options Table C-13. General SNMP Management Configuration Options C-30 SNMP NMS Security Configuration Options Table C-14. SNMP NMS Security Configuration Options C-31 SNMP Traps Configuration Options Table C-15. SNMP Traps Configuration Options (1 of 3) C-32 Table C-15. SNMP Traps Configuration Options (2 of 3) C-33 Table C-15. SNMP Traps Configuration Options (3 of 3) C-34 Configuration Worksheets C-35 Sync Data Port Options (Port 1) Value (Default in Bold) C-36 Sync Data Port Options (Port 2) Value (Default in Bold) C-37 Network Interface Network Channel Allocation C-38 DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation C-39 DTE Signaling Assign: (N1 24) Voice RBS or Data) C-40 Sync Data Port Channel Options Value (Default in Bold) C-41 General Options Value (Default in Bold) User Interface: Communication Port Options Value (Default in Bold) User Interface: External Device Options Value (Default in Bold) C-42 C-43 Communication Protocol Options Value (Default in Bold) General SNMP Management Options Value (Default in Bold) SNMP NMS Security Options Value (Default in Bold) C-44 D-1 Pin Assignments D Equipment List T1 Network Interface Page D-3 DTE Drop/Insert Interface DTE Interface Configuration Options D-4 AUX Port Interface D-5 COM Port Interface Page D-7 EIA-530-A Port Interface Connector D-8 EIA-530-A-to-RS449 Adapter Figure D-6. EIA-530-A-to-RS449 Adapter The EIA-530-A-to-RS449 adapter (Figure D-6) provides the RS449 interface shown in Table D-6. D-9 Table D-6. RS449 Cable Interface Signal Circuit Mnemonic CCITT D-10 EIA-530-A-to-V.35 Adapter Figure D-7. EIA-530-A-to-V.35 Adapter The EIA-530-A-to-V.35 adapter (Figure D-7) provides the V.35 interface shown in Table D-7. D-11 Table D-7. V.35 Cable Interface Signal CCITT D-12 EIA-530-A-to-X.21 Adapter The EIA-530-A-to-X.21 adapter (Figure D-8) provides the X.21 interface shown in Table D-8. Figure D-8. EIA-530-A-to-X.21 Adapter Table D-8. X.21 Cable Interface Signal CCITT D-13 Serial Crossover Cable Figure D-9. Serial Crossover Cable D-14 External Clock Interface E-1 SNMP MIB Objects E MIB II (RFC 1213) E-2 System Group, MIB II Company OID ssssssss zzzz-zzz yy.yy.yy Interface Group, MIB II E-4 n E-5 E-6 E-7 IP Group, MIB II E-8 E-9 E-10 ICMP Group, MIB II TCP Group, MIB II UDP Group, MIB II E-11 Transmission Group, MIB II DS1/E1 MIB (RFC 1406) E-12 Near End Group, DS1/E1 MIB E-13 E-14 E-15 E-16 Far End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB E-17 RS-232-like MIB (RFC 1317) General Port Table, RS-232-like MIB E-18 E-19 Asynchronous Port Table, RS-232-like MIB E-20 Synchronous Port Table, RS-232-like MIB Input Signal Table, RS-232-like MIB E-21 Output Signal Table, RS-232-like MIB Generic-Interface MIB Extensions (RFC 1229) E-22 Generic Interface Test Table, Generic Interface MIB E-23 E-24 Enterprise MIB F-1 IP Network Addressing Scenario F IP Network Addressing F-2 G-1 Equipment List G Equipment Feature Number Page GL-1 Glossary GL-2 GL-3 GL-4 GL-5 GL-6 GL-7 GL-8 GL-9 Page IN-1 Index A B C IN-2 D E F I IN-3 L M N O IN-4 P Q R S IN-5 T U V W X