C2443M-D (10/05) 11QUICK START GUIDE – SYSTEM SETUPQuick Programming Guide
Access main menu (preset 95). See the
Accessing Main Menu
(Preset 95)
section.
Use the joystick* to position the cursor beside menu selection.
Press Iris Open, the submenu/cursor moves to the right.
Move the joystick up or down to view selections.
Press Iris Open to make selection.
Press Iris Close to cancel selection.
SPECTRA III
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
ACK ALERT**
EXIT
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
BACK
EXIT
PRESET NUMBER 1
* * * PRESET NOT DEFINED * * *
POWER UP ACTION AUTO
BACK
EXIT
AUTO FLIP
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
SCAN SPEED DEG/S
PRESET FREEZE FRAME
CAMERA
TYPE OF LIGHTING
AUTO FOCUS
ZOOM LIMIT
BACK
EXIT
DISPLAY SETUP
PRESET LABEL (2 SECS)
ZONE LABEL (2 SECS)
ZOOM (2 SECS)
AZIMUTH/ELEVATION (2 SECS)
DIRECTION (2 SECS)
ALARM MESSAGE (2 SECS)
<LABEL POSTIONS>
RESTORE FACTORY DEFAULT
BACK
EXIT
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
FPGA VERSION X
VIDEO LEVEL NORMAL
CAMERA XXXX-XXXX
BACK
EXIT
18304
POWER ON
0O
YES
YES
DOME DRIVE MODEL
BACK BOX MEMORY
SOFTWARE VERSION
BIOS VERSION
FONT VERSION
COMM
D ADDRESS
P ADDRESS
CM9500 MODE
32 PRESETS
PROTOCOL
DD53M22
AVAILABLE
XX.X
XX.X
XX.X
2400, N, 8, 1
1
2
OFF
OFF
C
SYSTEM INFORMATION
<ADDITIONAL>
BACK
EXIT
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
LIMIT STOPS
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
LINE SYNC ON
LINE SYNC PHASE 0
BACK
EXIT
ZONE NUMBER 1
* * * ZONE NOT DEFINED * * *
<EDIT ZONE LABEL>
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
BACK
EXIT
PATTERN NUMBER 1
<PROGRAM PATTERN>
<CLEAR PATTERN>
BACK
EXIT
REFERENCE INFORMATION
PATTERN USAGE 0%
REMAINING 100%
<SET WINDOWS>
STYLE GRAY
BLANK ALL ABOVE OFF
BLANK ALL BELOW OFF
BACK
EXIT
RESUME OFF
SEQUENCE (SECS) 5
RESET DELAY (SECS) 0
<ALARM SETTINGS>
BACK
EXIT
AUX 1 MODE
DWELL TIME (SECS)
AUX 2 MODE
DWELL TIME (SECS)
BACK
EXIT
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
BACK
EXIT
ENABLE PASSWORD
<EDIT PASSWORD>
BACK
EXIT
ADVANCED SETTINGS
WINDOW NUMBER 1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW NO
REVERSE
CLEAR WINDOW
BACK
EXIT
ALARM NUMBER
ALARM PRIORITY
ALARM ACTION
ACTIVATE AUX
ALARM CONTACT
BACK
EXIT
ADDITIONAL
LANGUAGE 1
LANGUAGE 6
OUTDOOR
ON
X176
MEDIUM
ZOOM SPEED
LOW LIGHT LIMIT
<ADVANCED SETTINGS>
2
SHUTTER SPEED AUTO
27
AUTO
66
8
ON
26
OFF
HIGH
ON
ON
0
NONE
25
AUTO
ON
MOTION
BACK
EXIT
POWER UP LINE SYNC
BACK
EXIT
PRESETS
-
-
-
-
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
REFERENCE INFORMATION
AZIMUTH
ELEVATION
ZOOM
CUSTOM CAMERA SETTINGS
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
PATTERNS ZONES
1
LOW
NONE
NO
N/O
WINDOW BLANKING
SET WINDOWS
TOGGLE
1
TOGGLE
1
ALARMS
ALARM SETTINGS
ALERT**
TEMPERATURE
DEWPOINT
PRESSURE
REFRESH
BACK
EXIT
0°C
0°F
0°C
0°F
0.0 PSIG
0.0 BAR
CURRENT READING**
REPEAT
ACK ACTION
RESET ALERT
BACK
EXIT
CONSTANT
ALWAYS ON
ACTIVATE AUX
<CURRENT READING>
NO
AUX CLEAR PASSWORD
1234567890
ABCDEFGHIJ
KLMNOPQRST
UVWXYZ.,-/
abcdefghij
klmnopqrst
uvwxyz#&:*
OK
CANCEL
SPACE
BACKSPACE
EDIT THE PASSWORD
----------
NO
OFF
ENGLISH X.XX
ITALIANO X.XX
LABEL POSITION
[[ZONE LABEL------]
[PRESET LABEL------]
[ALARM LABEL------]
[ALERT MESSAGE------]**
[TITLE TEXT]
SAVE AND EXIT
CANCEL AND EXIT
HELP
XXX
0
/-XX
0
NE
XXX.XX
PRESSURIZED** X.XX
ENABLE TITLE TEXT
<EDIT TITLE TEXT>
TITLE TEXT
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESS
SHARPNESS LEVEL
BACKLIGHT COMP
VIDEO LEVEL
BACK
EXIT
<AUX>
<TITLE TEXT>
<ALERT>**
<CLEAR>
<PASSWORD>
*If your controller does not have a joystick, use the up or down key.
**This setting only applies to Pressurized Spectra III SE dome systems with softwareversion 1.25 or higher. Spectra III systems that are not pressurized or pressurizedsystems that do not have dome drive software version 1.25 or higher will not displaythis menu item.Software version 1.25 or higher includes the software to monitor temperature,pressure, and dew point for Pressurized Spectra III SE systems.