INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C4.
C5. Mount the Microwave Oven
IMPORTANTNOTES:
•Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
C1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to 3⁄4″(19 mm) onto
each bolt.
1
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING (Non-Vented Ductless)
C
Install or change Charcoal Filter
C3. Check Blower Plate
NOTE:
Cabinet
Cabinet
If the cabinet depth including the cabinet doors
is more than 13""'' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust.
o
EN-20
3/8"T
OEDGE
%#76+10Ä+(':*#756#ਸ਼+5215+6+10'&1765+&'
4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..
&+5%*#4)'+061*175'5647%674'
/+0+/7/9+&6*4'37+4'&
4'#49#..6'/2.#6'
NOTE:ITIS VERY IMPORTANT TO
READ AND FOLLOWTHE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDINGWITH THIS
REAR WALL TEMPLATE.
This RearWallTemplate serves topositionthe bottom
mounting plateand tolocatethehorizontal exhaust
outlet.
1.Usea leveltocheck that the template ispositioned
accurately.
2. Locate and mark atleast onestud onthe left or
right side ofthecenterline.
016'
Itisimportantto use at leastone wood
screwmounted firmly in astudtosupport the weight
of themicrowave.Marktwo additional,evenlyspaced
locationsfor the suppliedtoggle bolts.
3. Drill holes inthe marked locations.Where thereis
a stud,drilla 3/16"holefor wood screws. Forholes
thatdo notline upwith astud, drill5/8"holesfor
toggle bolts.
016'
DO NOTINSTALL THEMOUNTINGPLATE
ATTHIS TIME.
4. Remove the template from the rear wall.
5. Reviewthe InstallationInstructionbook foryour
installationsituation.
Locateandmark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONESTUD ON EITHER SIDEOF
THECENTERLINE.
MARK THELOCATION FOR2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTSIN THEMOUNTINGPLATE
AREA.
Locate andmark holes to alignwith holes inthe
mounting plate.
IMPORTANT:
LOCATE AT LEASTONESTUD ON EITHER SIDE OF
THECENTERLINE.
MARK THELOCATION FOR2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTSIN THEMOUNTINGPLATE
AREA.
Trim the rear wall template along the dottedline.
Trim the rear walltemplate alongthedottedline.
%
(%76176(14*14+<106#.
1765+&'':*#756
%76*1.'6*417)*4'#49#..(14':*#756#ਸ਼
12"
4"
Darlevueltaalahojaparaconsultarla
versiónenEspañol.
IMPORTANT:Do not remove the cardboard
etween the heat shield and door.spacers b