Phoenix Gold pm700, pm950

67 89 10 11 12

6. BRIDGED OPERATION

The STEREO/MONO switch is located just behind the input panel. This switch is used to select between

NORMAL STEREO operation, DUAL MONO operation, or BRIDGED MONO operation. For NORMAL

STEREO operation, use CH 1 and CH 2 inputs. For DUAL MONO or BRIDGED MONO operation, use

CH 2 input only (see page 14 for instructions on how to access the Stereo/Mono switch, and page 10 for

more information about Bridged Operation).

7. SEQUENCE SND/RCV

These barrier strip screw terminals are used to link multiple amplifiers for sequenced turn-on. Connect the

SND (SEND) terminal of the first amplifier to the RCV (RECEIVE) terminal of the second amplifier.

Connect the SND terminal of the second amplifier to the RCV terminal of the third amplifier, and so on

(see page 11 and 12 for more information on Power ON sequencing).

8. CLIPPING ELIMINATOR SWITCH

The Clipping Eliminator circuit can be activated with a switch located just behind the input panel. Moving

the switch down will deactivate the Clipping Eliminator, allowing the amplifier to clip when driven beyond

its maximum output capability. To access the CLIPPING ELIMINATOR DEFEAT Switch, see page 11 of

this owner’s manual for instructions.

9. CH1 /CH2 INPUT CONNECTORS

There are two methods for making input connections to the amplifier. 1/4-inch TRS (Tip-Ring-Sleeve)

connections are provided as well as professional XLR connectors. They can be used with balanced signals

or unbalanced signals (see Input Wiring on page 9 for more information).

Note: Ahigh-quality input transformer option is available for the pm700 and pm950 power amplifiers.

Contact your Carver Professional Dealer for details.

10. FAN EXHAUST

This opening releases hot air from inside the amplifier. Be sure this vent is clear of obstructions for

maximum cooling efficiency.

11. CH1/CH2 SPEAKER OUTPUTS

Multi-way binding posts are used to connect the loudspeakers to the amplifier outputs. The red terminals

are the signal connection (+) and the black terminals are the signal return connection (–). The black

terminals are internally tied together and to signal ground.

12. POWER CORD

Connect to a properly configured outlet providing the line voltage specified for your model.

∞

214 5

3 4

Controls And Functions

1. POWER SWITCH

When this switch is engaged, the power turns ON and the READY indicators illuminate. Be sure all

connections are made and double-checked before switching the power amplifier on.

2. STANDBY LED

This indicator illuminates when the power switch is turned OFF. It also lets you know when the amplifier

is connected to AC power. When the power switch is OFF and the amplifier is plugged into an AC outlet,

the LED illuminates to indicate that AC power is available and the amplifier can be powered up. When the

power switch is ON, the LED turns off.

3. AC POWER FUSE

This protects the amplifier from catastrophic failures that could damage internal circuitry. Repeated fuse

blowing is a sign of internal distress. See page 15 for information on authorized Carver Professional

Service.

Caution: Always replace with the same type and value fuse indicated next to the fuseholder.

4. CH1/ CH2 LEVEL CONTROLS

These controls are used to adjust the input level of each channel. When the controls are fully clockwise the

amplifier operates at maximum gain. Turning the controls counter-clockwise attenuates the input signal.

The Level controls can be bypassed internally to lock the amplifier at its full gain capacity. See page 14 for

information about the Level Defeat Switch.

Note: Aprecision attenuator is available as an option for the pm700 and pm950, which can be installed

inside the amplifier (see page 13). Contact your Carver Professional Dealer for details.

5. CH1/CH2 STATUS INDICATORS

These LEDs display information about the operation of the amplifier.

READY –These LEDs illuminate green when the power is on and the amplifier is ready to operate. The

READYLEDs illuminate red when the power switch is first turned on (while the power supply is stabilizing

prior to the speaker output relays switching in), or when the amplifier is in protect mode.

SIGNAL –These LEDs illuminate yellow when a signal is present at the Speaker Output jacks to provide

an indication of output power relative to full power (0dB).

CLIP/PROTECT –These LEDs illuminate red when the power switch is first turned on, when the output

begins to clip, or whenever there is a fault condition detected that causes the output relay(s) to disengage.

These fault conditions include excessive DC Offset, excessive heatsink temperature and short circuits at the

speaker output(s).

Note: The relays operate independently for each channel. Therefore, it is possible for one channel to operate

normally while the other is in “protect” mode.