Pioneer DEH-P3300, DEH-P33

Fig. 2

Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300mA

12 V DC).

Connecting cords with RCA pin plugs

(sold separately)

System remote control

Right

Front speaker

White Gray

White/black

Green

Green/black

Gray/black

Violet

Violet/black

Front speaker

Left

Perform these connections when using a

different amp (sold separately).

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Black (ground)

To vehicle (metal) body.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Orange/white

To lighting switch terminal.

Rear Speaker

or Subwoofer Rear Speaker

or Subwoofer

Rear Speaker

or Subwoofer Rear Speaker

or Subwoofer

Power amp

(sold separately)

Fuse

IP-BUS cable

IP-BUS input (Blue)

This Product

Antenna jack

Rear or Subwoofer output

Multi-CD player

(sold separately)

Note:

When a subwoofer is connected to this unit instead of a rear speaker,

change the rear output setting in the Initial Setting. (Refer to the

Operation Manual.) The subwoofer output of this unit is monaural.

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠battery cable before beginning

installation.

• Refer to the owner’s manual for details on con-

necting the power amp and other units, then make

connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠speaker leads are common.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers catch-

ing fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.

Connect to an external power amp’s system remote

control or the car’s Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do not

connect the blue/white lead to the power terminal

of the auto-antenna. Such connection could cause

excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a possi-

bility of short-circuiting if the leads are not insulat-

ed.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same colors

correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be connected

to a terminal coupled with ignition switch ON/OFF

operations. If this is not done, the vehicle battery

may be drained when you are away from the vehi-

cle for several hours. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the ground

becomes detached, there is a risk of damage to the

products or fire.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

No ACC positionACC position

Connecting the Units

INSTALLATION MANUAL

MANUEL D’INSTALLATION

DEH-P3300

DEH-P33