Manuals / Regency / Household Appliance / Indoor Fireplace

Regency L900-NG Operating Instructions, Matching Remote Handset & Control BOX ID Code, First Fire

Models: L900-LP L900-NG

1 56
Download 56 pages 54.9 Kb
Page 39
Image 39

OPERATING INSTRUCTIONS

MATCHING REMOTE

HANDSET & CONTROL

BOX ID CODE

The Remote Control Handset has a set of unique ID codes that is pre-programmed into its memory. This set of ID codes helps to differenti- ate one Remote Control Handset from another so that only the control box with a matching ID code will respond to the appropriate Remote Control Handset.

To ensure the remote control is matched to the receiver correctly, please follow the steps below:

1.Ensure that the Remote Control and the 3-way switch located at the appliance are both in the OFF position.

2.Ensure that the pilot is lit and the pilot control knob is in the ON position on the appliance.

3.Install the 2 x AAA alkaline batteries into the Remote Control.

4.Unplug and re-plug the power cord. The power cord is located on the left hand side of the appliance and will be plugged into the receptacle.

5.Switch the 3-way switch located on the ap- pliance to the REMOTE position.

6.Press and hold the PROG and FAN buttons simultaneously for up to 20 seconds. During this time, the remote will display LC while it is transmitting codes to the receiver. Once it is successfully transmitted, one will hear the solenoid click and the burners will come on. If is does not work the fi rst time, repeat steps 1 - 6.

7.Release both the PROG and FAN buttons. The remote will revert back to normal, but the burner will still be on.

8.Press the ON/OFF button on the remote control 2 times to turn the burner off.

9.The remote control is now programmed to the receiver and the appliance can now be operated with it.

The control box will only learn the Remote ID codes during the fi rst 30 seconds after power is applied and will ignore this special command from the Remote after the fi rst 30 seconds.

NOTE: This must only be performed by a quali- fi ed installer.

OPERATING

INSTRUCTIONS

1)Read and understand these instructions before operating this appliance.

2)Check to see that all wiring is correct and enclosed to prevent possible shock.

3)Check to ensure there are no gas leaks.

4)Make sure the glass in the door frame is properly positioned. Never operate the appliance with the glass removed.

5)Verify that the venting and cap are unobstructed.

6)Ensure that the brick panels are installed.

7)Verify log placement. If the pilot cannot be seen when lighting the unit, the logs have been incorrectly positioned.

8)The unit should never be turned off, and on again without a minimum of a 60 second wait.

FIRST FIRE

The FIRST FIRE in your heater is part of the paint curing process. To ensure the paint is properly cured,it is recommendedyou burnyourfireplace for at least four (4) hours the fi rst time.

When fi rst operated, the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufac- turing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours. The glass may require cleaning.

NOTE: The main burner will always start on "HIGH" and resume it's last setting after 20 seconds of operation.

NOTE: When the glass is cold and the appliance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.

DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS STILL HOT!

During the first few fires, a white film may develop on the glass front as part of the curing process. The glass should be cleaned after the unit has cooled down or the film will bake on and become very difficult to remove. Use a non-abrasive cleaner and DO NOTATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT.

LIGHTING

PROCEDURE

IMPORTANT

To ignite or reignite the pilot, you must first remove the glass door.

Only when the pilot holds, without pressure being applied to the control knob, resecure the glass door to the unit. The unit must not be operated with the glass door removed.

IMPORTANT Gas on/off knob cannot be turned from "PILOT" to "OFF" unless it is partially depressed.

Ensure that the 3 way switch on the manual control panel is in the "Remote" position.

The manual control panel is located on the left hand side of the fi rebox behind the left side exterior brick panel.

3-way Switch

OPERATION

Regency® L900 Direct Vent Gas Fireplace

39

Page 38 Page 40
Page 39
Image 39
Regency L900-NG Operating Instructions, Matching Remote Handset & Control BOX ID Code, First Fire, Lighting Procedure
Page 38 Page 40

L900-LP, L900-NG specifications

The Regency L900-NG and L900-LP are remarkable gas fireplaces that epitomize both elegance and efficiency, bringing a blend of modern technology and traditional aesthetics to any living space. Designed for versatility, these units are suitable for homes with natural gas (NG) or propane (LP) gas lines, thus catering to a wide range of customer preferences.

One of the standout features of the L900 series is its impressive heating capacity. With up to 30,000 BTUs, these fireplaces can efficiently warm large areas, making them an exceptional choice for both residential and commercial settings. Their exceptional airflow and heat distribution ensure that users enjoy a cozy ambience throughout the space.

The L900 models are integrated with cutting-edge technology that enhances user experience. The advanced electronic ignition ensures reliable start-ups, while the variable flame height adjustment provides flexibility, allowing users to customize the heat output according to their needs. The inclusion of an optional remote control system adds an extra layer of convenience, enabling homeowners to operate the fireplace from anywhere in the room.

Aesthetic appeal is also a major highlight of the Regency L900 series. The full-view glass front maximizes the viewing area, allowing users to enjoy the mesmerizing flames fully. The sleek, contemporary design can easily complement various interior styles, from modern to traditional settings. Moreover, with several customizable options, including media choices such as glass, pebbles, or logs, users can personalize their fireplace to suit their decor.

Safety is always a priority with Regency products. The L900 models come equipped with a safety shut-off valve that activates in case of any irregularities, providing peace of mind for users. Additionally, the fireplace’s direct venting system ensures that combustion gases are safely expelled outside, allowing for effective ventilation without compromising indoor air quality.

Durability is another significant characteristic of the Regency L900 series. Constructed from high-quality materials, these fireplaces promise longevity and resilience, ensuring they can withstand the test of time.

Overall, the Regency L900-NG and L900-LP gas fireplaces stand out for their combination of performance, efficiency, and style. With their advanced features, customizable options, and focus on safety, they provide an enticing heating solution for any home or business, merging warmth with a touch of elegance.