Renesas M306H7T3-RPD-E 4.3 Connection Diagram

M306H7T3-RPD-E User’s Manual 4. Hardware Specifications

REJ10J0964-0100 Rev.1.00 August 01, 2005 Page 72 of 88

4.3 Connection Diagram

Figure 4.1 shows a connection diagram of the M306H7T3-RPD-E. This connection diagram mainly shows the interface section.

The circuits not connected to the user system such as the emulator's control system are omitted. The signals not shown in

Figure 4.1 connect the evaluation MCU and the user system directly.

Tables 4.3 to 4.4 show IC electric characteristics of this product for reference purposes.

Figure 4.1 Part of the connection diagram of the M306H7T3-RPD-E

M306H7FG-TOOL(IC8)

I/O Emulate MCU

P60--P67

P70--P77

P80--P84

P90--P97

P85/NMI

100Ω

P86/Xcout

P85/NMI

P86/Xcout OPEN

SW5 P86/Xcout

SW3 P87 P87/Xcin

P87/Xcin Xcin

SW4 OPEN

Xout Xout

CNVSS

1KΩ

SW2

P62F2(IC4)

Port Emulate FPGA

P00--P07 P00--P07

33Ω

RM1

Socket mounted

33Ω

Socket mounted

RM2

P10--P17

P10--P17

33Ω

P20--P27

Socket mounted

RM3

P20--P27

Socket mounted

33Ω

P30--P37 P30--P37

RM4

33Ω

P40--P47

Socket mounted

P40--P47

RM5

33Ω

P50--P57

Socket mounted

P50--P57

RM6

100KΩ

Xout

CNVSS

P90--P97

P80--P84

P70--P77

P60--P67

AN00--AN07

VDDIO

VDDIO

VDD2

VDD2

VDD2

VDD2

VDD2

VDD2

74HC4066

Contents

Main M306H7T3-RPD-E Users Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT Page CAUTION Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger (M16C PC4701 Emulator Debugger) 2.3 Connecting the Host Machine 2.4 Connecting the PC4701 Page Page 2.5 Turning ON the Power LED display when the emulator starts up normally This does not light when the user system is not connected. : On : Off 2.6 Downloading Firmware M306H7T3-RPD-E Users Manual 2. Setup SAFE and ERROR LED blink Target status error 2.7 Self-check Figure 2.7 LED display in the self-check procedure (1) All the LEDs light Completed normally : Blinking : On : Off SW1 SW2 SW4 SW3 SW5 JP5 JP6 JP7 JP1 JP2 JP3 JP4 2.8 Connecting the User System Page Page Page Page 2.9 Changing Settings Page Page Page Page Page Page Page Page VCC P5 P4 P3 P2 P1 P0 RM1 -- RM6 IC8 C7 AVSS AVCC M306H7T3-RPD-E Users Manual 2. Setup Figure 2.23 Connection diagram of circuits connected to the data slicer Figure 2.24 Arrangement of the parts used for each circuit 3. Usage (How to Use the Emulator Debugger) 3.1. Making an MCU File 3.2 Setting the Work Area 3.3 Starting Up the Emulator Debugger Page Page Page Page Page Page 3.4 Downloading Program 3.5 Program execution Page Page 3.6 Hardware Break Page Page Page 3.7 Trace Window M306H7T3-RPD-E Users Manual 3. Usage (How to Use the Emulator Debugger) 3) Trace Window (Bus mode display) 4) Trace Window (Disassemble mode display) 5) Trace Window (Source mode display) Page Page 3.8 RAM Monitor Window 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page M306H7T3-RPD-E Users Manual 4. Hardware Specifications 4.3 Connection Diagram Figure 4.1 Part of the connection diagram of the M306H7T3-RPD-E Page 4.4 External Dimensions Page 4.5 Notes on Using This Product Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair