RF-RBWS01 Wireless Bookshelf Speakers
Package contents
|
|
|
|
| AC power adapter |
|
|
|
| 3.5 mm | for wireless speakers |
AC power adapter |
|
|
| ||
|
| audio cable |
| ||
|
|
| |||
for wireless sender/receiver |
|
|
|
| |
Wireless sender/receiver |
|
|
|
|
|
|
| 3.5 mm to RCA adapter |
| ||
USB cable | Remote control | (6 inches/15.25 cm) |
| ||
|
| User Guide | Quick Setup Guide | ||
Wireless speakers |
|
|
| ||
|
|
|
|
|
Connecting power to the wireless speaker
Connect the AC power adapter to the wireless speaker and plug into an AC power outlet. The
wireless speaker system turns on automatically. | DC IN |
15V/1.5A | |
|
Connecting audio source and power to wireless sender/receiver
Establishing communication
The wireless sender/receiver and wireless speakers were
If you need to rejoin the wireless sender/receiver to the wireless speakers, and this is your only Rocketboost enabled product, then use the following steps.
1 | Set the HUB STATUS switch on the wireless sender/receiver to ENABLE if this is your first | ||
| Rocketboost product set. | ||
| • The power indicator turns green when the HUB STATUS switch is set to ENABLE. | ||
| • The power indicator turns blue when the HUB STATUS switch is set to DISABLE. | ||
2 | Press and hold |
| on the wireless sender/receiver for more than three seconds to put it into |
| |||
| |||
| joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode |
Every Rocketboost network must contain one hub device, which helps devices join the network. The network can have only one hub, which you can enable using the hub switch on the back of all Rocketboost wireless sender and wireless sender/receivers. If this is your first Rocketboost product, you should make the wireless sender/receiver the hub, if you already have Rocketboost products, you should disable hub mode on this device.
Important: Hub devices must always have power for your network to operate. TheInitial setup
1Unpack the package contents
2Adjust the antennas
Adjust the antennas to gain the best audio signals.
Tip: In some cases, you may improve range by rotating both antennas 0° to create a 180° angle.
3 Enable the remote control battery Remove the tab from the bottom of the remote control.
4Set up the wireless sender/receiver and wireless speakerThe Quick Setup Guide will show you a typical setup using an audio device (such as an MP3 player, PC or A/V receiver). For more information about how to use other Rocketboost products with this product, see your User Guide.
See the following steps for further setup details.
Wireless | Wireless |
sender/receiver | speakers |
1Connect your audio source to the LINE IN jack or USB jack on the rear of the wireless sender, using the 3.5 mm audio cable or the USB cable. If necessary, you can also use the 3.5 mm to RCA adapter, if your audio device uses
Included 3.5 mm cable |
|
| Included 3.5 mm cable | ||||
|
| and 3.5 mm to RCA adapter | |||||
| |||||||
|
|
|
|
| OR |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| To audio output jack |
|
| To audio | |||
|
|
|
|
|
|
| output jack |
2Remember to turn the volume up on your audio source especially if connected to a headphone output.
3Connect the AC power adapter to the wireless USB sender/receiver and plug into an AC power outlet.
The wireless sender/receiver automatically turns on and the power indicator turns green.
| for 30 seconds. | ||
3 | Press and hold the |
| button on the wireless speaker for more than three seconds |
| |||
| |||
| so the wireless sender/receiver and wireless speaker enter connection mode. | ||
| • The power indicator lights steadily if the joining was successful. | ||
| • The power indicator blinks slowly if the joining was not successful. | ||
4 | After the link is established, if the Source indicator on |
the wireless speaker is still not illuminated, make sure that your source is turned on.
For more instructions, see your User Guide. |
|
| Lights when | |
| ||||
standby |
| speaker is | ||
If you already have other Rocketboost devices you need | SOURCE |
| ||
|
| receiving | ||
to join both the wireless sender/receiver and the wireless |
|
| audio from | |
speaker to your existing hub device. See the User Guide |
|
|
| sender |
|
|
|
| |
for detailed instructions on how to do this. |
|
|
|
Listening to music
1Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should light steadily. If they are blinking you need to rejoin the wireless sender/receiver and wireless speaker. See the Establishing communication section above.
2Point the remote control at the wireless sender/receiver and select either
3Play music from the audio device connected to your wireless sender/receiver and listen to it from the wireless speakers.
4Adjust the volume level on your wireless speaker. If you have multiple audio sources in your Rocketboost network, press the Source button on the wireless speaker to hear the next audio source. Press the Source button again to cycle through all available audio sources.
Note: Be sure to turn up the volume on your audio source device, especially if you are connected to a headphone output.
QUICK SETUP GUIDE
©2011 BBY Solutions, Inc. All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA