Package contents
Please read before setting up your system.
Every Rocketboost network must contain at least one hub device, which directs network data traffic and helps devices join the network. The network can have only one hub, which you can enable using the Hub switch on the back of all Rocketboost
| DC adapter |
IR remote | for wireless |
speaker |
3.5mm stereo
female to 2-RCA male cable (6 inches/15.25 cm)
transmitters. See your User Guide for instructions on“joining” devices to the network. If this is your first Rocketboost product you should make this unit the hub, if you already have Rocketboost products, you should disable the hub mode on this device.
IMPORTANT: Hub units must always have power for your network to operate. The device may be placed in standby, but the unit must remain plugged into the wall to operate your network.
3 Establishing Communication
If this is your first Rocketboost product and you do not have an existing Rocketboost network, the devices were joined at the factory.You do not need to join them. If you are adding these devices to an existing network, change the hub mode switch on the sender to Disabled and then join BOTH devices to your existing hub.
| TM | |
| DC adapter | |
Sender | for transmitter | |
Wireless speaker | ||
|
Front controls
| Guide |
|
| User |
|
|
| GUIDE |
|
| SETUP |
|
| QUICK |
|
| Quick |
3.5 mm | User Guide | Setup Guide |
|
| |
stereo cable |
|
|
1 Getting Started
Load batteries in wireless speaker (Installing batteries is optional)A Unscrew the bottom cover ( 3 screws). |
B Insert eight alkaline or rechargeable NiMH batteries |
matching +/- as indicated.This product will only recharge |
NiMH batteries. Do not attempt to charge any other |
batteries in this product. Note: Your wireless speaker can |
Charge your wireless speaker
Connect the DC adapter to the wireless speaker and plug into an AC power outlet. The CHARGE LED blinks green while it is charging. The light will be solid when charging is complete.
Note: For the first time, charge batteries forUse this procedure only if you need to rejoin the transmitter and speaker.This procedure
Transmitter | # | Feature |
| ||
| 1 | Power/Join button |
operate on batteries or with the DC to AC adapter (provided). |
The unit will charge and play simultaneously. |
C Replace the cover and fasten the three screws. |
16 hours.
15V DC
is not required for normal operation as devices were joined at the factory.To connect these devices to an existing hub device that you own, follow the same instructions: Join the sender/receiver to your existing hub, then join the wireless speaker to your existing
|
|
| 2 | Power/Join indicator (Blue/Green Light) | |
| TM |
| 3 | Standby indicator (Red Light) | |
|
|
|
| ||
| TM |
| 4 | IR sensor window | |
|
|
| |||
|
|
| 5 | Source button | |
1 2 3 | 4 | 5 6 7 | 6 | ||
Front Panel |
|
| 7 | ||
|
|
|
| ||
Speaker | POWER/ /JOIN |
| # | Feature | |
Front Panel | 6 | ||||
| 1 | Volume increase/decrease dial | |||
|
|
|
Wireless speaker | 8 rechargeable or alkaline |
| C batteries (not included) |
x 8
2 Connecting theTransmitter
Caution: Only use the supplied power adapter and make sure your outlet matches the AC’s input of
BASS
Wireless speaker’s
back panel
hub. Note:You can only join devices to the hub unit (the one with the green LED).
Rocketboost deviceA Set the HUB STATUS switch to ENABLE if this is your first Rocketboost product set. |
• The LED lights green when the HUB STATUS switch is set to ENABLE. |
• The LED lights blue when the HUB STATUS switch is set to DISABLE. |
B Press and hold the button on the sender/receiverfor more than three seconds to |
put it into joining mode. The LED starts blinking rapidly and the unit will stay in Join |
mode for 30 seconds. |
C Press the Power/Join button on the wireless speaker for more than three seconds |
so the sender and wireless speaker will enter connection mode. |
1
2
VOL
VOL
Source
12
11
3
BASS
CHARGE
4 4
CHANNEL
L - MONO - R
SOURCE
5 5
72 Power/on standby/Join button
8 | 3 | Source | |
4 | |||
| |||
| 5 | Bass reflex hole | |
| 6 | Power/Join indicator (Red/Blue light) |
97 BASS indicator
8 Charge indicator
109 Channel MONO (L/R) indicators
10Audio source signal indicator
11DC adaptor in
12Bass Boost
Connect to an audio source
Connect one end of the audio cable (supplied) to the AUDIO IN jack on the sender and the other end to the audio output jack of your device (such as an A/V receiver, PC, or iPod.)
Note: If you are adding this sender to an existing network, set the hub switch to Disable and follow the instructions under Establishing Communication to add the transmitter and speaker to your existing network. Otherwise, leave it on Enable as the transmitter and wireless speaker were
OR
Supplied |
Supplied |
To audio |
• The LED lights steadily if the link is activated between both of the units. |
• The LED blinks at a slower rate if the communication link is not successful. |
D Once the link is established, if the Source LED on the wireless speaker is not |
illuminated, press the Source button to toggle to the next source. If the LED is still |
not illuminated, check that your source is powered up. |
For further details, see instructions in the user manual for joining new devices to an |
existing Rocketboost network. |
4 Listening to Music
To listen to music:
Adjust antennas
Pull up the antennas
For best results, adjust the antennas to vertical. In some instances, you may improve range by rotating both
through the Establish Communication steps. Remember to turn the volume up on the source device to at least 80% of its maximum volume.
To audio |
|
output jack | output jack |
A Turn on the sender and the wireless speaker. Make sure that the wireless |
speaker is fully charged (if using Batteries) and there is an active link |
between the sender and the wireless speaker. An active link will be |
indicated by the Power LED showing a solid blue. |
B Make sure the volume is turned up to about 80% of maximum volume. |
Connect the AC Adapter
C Adjust the volume level on your wireless speaker. If you have multiple |
streams in your Rocketboost network, press the Source button on the |
Preparing the remote control
To activate the battery:Remove the tab from the bottom of the remote control to enable the battery.
Connect one end of the adapter to the DC IN jack, then plug the other end into an AC power outlet. The standby indicator turns red.
Note: Make sure that the power outlet is
wireless speaker to hear the next stream. |
Repeated pressing of the SOURCE button will toggle through available |
sources. |
ENGLISH
QUICK SETUP GUIDE