RocketFish RF-TVMFM01 manual

RF-TVMFM01_10-0451_QSG_V2_EN_finalLR.pdf 1 8/23/2011 11:56:36 AM

QUICK SETUP GUIDE

RF-TVMFM01

Thank you for choosing the Rocket￿sh RF-TVMFM01. The RF-TVMFM01 TV mount is designed to support a ￿at-panel TV weighing up to 15.8 kg (35 lbs.).

1 Install the arm assembly

Option 1: Installing to a wood stud wall

Note: Any material covering the wall must not exceed 16 mm (5/8 in.).

1Locate the stud. Verify the center of the stud with an awl or thin nail or use an edge-to-edge stud ￿nder.

2	Level the arm assembly (A) and mark the hole locations.	<16 mm
3	Drill pilot hole to a depth of 75 mm (3 in.) using a	(5/8 in.)
4	5.5 mm (7/32 in.) diameter drill bit.
	Align the arm assembly (A) with the
	pilot holes, insert the coach screws (G)
	through the holes in the arm
	assembly, then tighten
	the coach screws only until
	they are pulled ￿rmly
	against the arm assembly.
	CAUTION: Avoid potential
	injuries or property damage!
	DO NOT over-tighten the
	coach screws (G).

Wall	75 mm
	(3 in.)

203.2 mm (8 in.)

8 in.

TV

139.7 mm(5-1/2 in.)

TV shifts 139.7 mm (5-1/2 in.) in. from the home position to full extension.

2 Attach the mounting hardware

Option 1: For TVs with inset mounting or that require extra space for wires

Install spacers (E), washers (D), and screws (C) into the top two holes in the back of the TV. Leave a gap between the spacer and the washer and screw.

Note: Only install the hardware in the top two screw holes at this time. The remaining hardware will be installed in Step 3.

Gap

NOTE: If the hole pattern on your TV is 75 mm x 75 mm the washers (D) will not be used.

Package contents

A Arm assembly (1)

M4 bag

B M4 × 12 mm screws (4)C M4 × 30 mm screws (4)D M4 washers (4)E M4 spacers (4)

Hex key bag			M4 bag
F	4 mm (5/32 in.) hex key (1)
Coach Screw bag			M4 × 12 mm
G	8 mm (5/16 in.)× 70 mm
H	(2 3/4 in.) coach screw (2)		M4 × 30 mm
	Concrete anchor (2)
Cable ties
			M4	M4
Hex key bag		Lag Bolt Bag

4 mm
(5/32 in.)	8mm (5/16 in.)× 70 mm (2 3/4 in.)
Cable ties

Option 2: Installing to a solid concrete or concrete block wall1Level the arm assembly (A) and mark the hole locations.2Drill pilot hole to a depth of 75 mm (3 in.) using a9.5 mm (3/8 in.) diameter drill bit.

3 Insert the concrete wall anchors (H) into the pilot holes and make sure that the anchors are seated ￿ush with the concrete surface.

4Align the arm assembly (A) with the anchors, insertthe coach screws (G) through the holes in the arm assembly,

then tighten the coach screws only until they are pulled ￿rmly against the arm assembly.

CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the coach screws (G).

75 mm(3 in.)

CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount wall plate directly onto the concrete surface.

Option 2: For ￿at backed TVs

Install washers (D), and screws (B) into the top two holes in the back of the TV. Leave a gap between the back of the TV and the washer and screw.

Note: Only install the hardware in the top two screw holes at this time. The remaining hardware will be installed in Step 3.

Gap

NOTE: If the hole pattern on your TV is 75 mm x 75 mm the washers (D) will not be used.

Tools you will need:
•	Stud finder	•	Socket wrench with
•	Awl		12.7 mm (1/2 in.) socket
•	Pencil		or adjustable wrench
•	Level	• 5.5 mm (7/32 in.) wood drill bit
•	Tape measure	•	9.5 mm (3/8in.) masonry drill bit
•	Phillips screwdriver		(concrete only)
•	Hammer (concrete only)	•	Power drill