3 Install the wall plate

Option 1: Installing to a wood stud wall

Caution: Avoid potential injuries or property damage!

Option 2: Installing to a solid concrete or concrete block wall

Caution: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts.

5 Adjust the tilt angle (if necessary)

You can adjust the tilt angle of the screen ± 12°.
DO NOT over-tighten the lag bolts.Any material covering the wall must not exceed 5/8 in. (16mm).

a. Locate the stud. Verify the center of the stud with an awl or thin nail or use an

edge-to-edge stud finder.b. Level the wall plate (B)and mark the hole b. locations.c. Drill the pilot holes as illustrated.d. Align the wall platewith the pilot holes,B insert the lag bolts

(I)through the holes in the wall plate, then tighten the lag bolts with a socket wrench only until they are pulled

firmly against the wallplate.

d.

a. < 16 mm (5⁄8 in.)

c.

75mm 3 in.
Any material covering the wall must not exceed 5/8 in. (16mm).

a.

 

Caution: To prevent property damage

B

or personal injury, never drill into
mortar between blocks.

 

c.

 

b.

 

< 16 mm

 

 

 

J

(5⁄8 in.)

 

 

d.

J

75mm 3 in.

a. Level the wall plate (B) and mark the hole locations.b. Drill the pilot holes as illustrated.c.Insert the concrete wall anchors

(J)into the pilot holes and use a hammer to make sure that the anchors are seated flush with the concrete surface.

d.Align the wall plate with the anchors, insert the lag bolts (I) through the holes in the wall plate, then tighten the lag bolts with the socket wrench only until they are pulled firmly against the wall plate.

If necessary, the tilt tension can be adjusted by tightening or loosening the tension knob with either the hex key (H) or by hand.

H

IMPORTANT SAFETY INSTRUCTIONS • SAVE THESE INSTRUCTIONS

Caution: Do not use this product for any purpose not explicitly specified by Rocketfish. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts

I

I

about the safety of the installation, contact Customer Service or call a qualified contractor. Rocketfish is not responsible for damage or injury caused by incorrect installation or use. The weight of your TV must not exceed 50 lb (22.7 kg). The wall must be capable of supporting five times the weight of the TV and wall mount combined.

4 Mount the TV to the wall

a.Slide the TV/wall bracket assembly down over the tabs on the wall plate (B), then tighten the locking screw with the hex key (H).

a.

B

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

5-year limited warranty
Visit www.rocketfishproducts.com for details.
We’re here for you
www.rocketfishproducts.comFor customer service, call:
800-620-2790 (U.S./Canada markets)
01 800-926-3010 (Mexico market)
© 2010 BBY Solutions, Inc., All Rights Reserved.

Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN USA 55423-3645

HEAVY!You will need

H

G

assistance with this step.

 

 

 

Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca, Programa Parcial de Desarrollo Santa Fe, Delegación Cuajimalpa, Distrito Federal, México 05349

ROCKETFISH is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

6907-002013<00>

10-0361