Where to Install Your

Mini-Compact System

GB

To take full advantage of your new mini-compact system, follow these installation instructions before connecting the unit.

Install the system on a flat, stable surface.

Never place this unit on carpeting.

Never place this unit in an outdoor area.

Maintain an open space of approximately 4 inches (10 cm) on the sides and rear of the system, for ventilation purposes.

Make sure that you have enough room to open the compact disc compartment easily.

Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.

Direct the loudspeakers towards the listening area.

For optimum performance, make sure that both speakers are placed at an equal distance above the floor.

Inserting Remote Control Batteries

Connecting the Loudspeakers

The loudspeaker connector terminals are located on the rear of the system.

There are four terminals on the system:

Two for the left speaker (marked L)

Two for the right speaker (marked R)

To achieve the correct sound quality, connect the:

Red wire to the + terminals

Black wire to the - terminals

1

To connect a wire to a terminal, push the tab as far as it will go:

 

To the right on the system

2

Insert the wire, up to the plastic sheathing, in the hole.

3

Push the tab back:

 

To the left on the system, until it clicks into place

 

Result: The wire is pinched and held firmly in place.

4

Repeat the operation for each wire.

Connecting the AM (MW) Aerial

The AM aerial (for long and medium waves) can be:

Placed on a stable surface

Fixed to the wall

The AM aerial connector terminals are located on the rear of the system and are marked AM.

To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires.

Always keep them at least 2 inches (5 cm) away.

(IMPEDANCE 4)

Connecting the FM Aerial

GB

There are two types of aerial, (depending on option chosen).

1 How to connect a COAXIAL TYPE aerial.

Connect a 75antenna to the FM antenna terminal.

Plug the connector on the FM aerial supplied into the coaxial socket (75) marked FM on the rear of the system.

Follow the instructions given on Page 10 to tune into a radio station, and determine the best position for the aerial.

If reception is poor, you may need to install an outdoor aerial.

To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75coaxial cable (not supplied).

FMFM

 

 

 

FM AERIAL

 

75COAXIAL CABLE

(supplied)

 

(not supplied)

2 How to connect a SCREW TYPE aerial.

The FM aerial connector terminals are located on the rear of the system and marked FM (75).

Spread the T.form FM aerial out and attach the ends to a wall, in the position providing the best reception.

Insert or replace remote control batteries when you:

Purchase the mini-compact system

Find that the remote control is no longer operating correctly

When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries.

1

Place your thumb on the position marked

on the battery compartment

 

cover (rear of the remote control) and push the cover in the direction of

 

the arrow.

 

2

Insert two AAA, LR03 or equivalent batteries, taking care to respect

 

the polarities:

 

 

+ on the battery against + on the remote control

 

on the battery against - on the remote control

3

Replace the cover by sliding it back until it clicks into position.

Connecting Your System to the Power Supply

The main lead must be plugged into an appropriate socket.

Before plugging your system into a main socket, you must check the voltage setting (OPTIONAL). If the voltage of the socket does not correspond to the setting on the rear of the unit, you may seriously damage your system.

1

Check the position of the voltage selector on the rear of the system

 

(OPTIONAL).

2

Plug the main lead (marked AC CORD on the rear of the system) into

 

an appropriate socket.

3

Press the POWER button to switch your mini-component system on.

option

Connecting the SW Aerial (option)

How to connect a WIRE TYPE aerial.

1

Spread the SW aerial out and attach the ends to a wall, in the position

providing the best reception.

If reception is poor (e.g. distance from transmitter too great, walls blocking the radio waves, etc.), install an outdoor aerial.

4

5