4. Connecting the Ordinary monitor

Connect the ordinary monitor to the Spot output terminal, which allows you to supervise a specified channel within the Main screen. Connect the Slave Monitor to the output terminal, which allows you to simultaneously view the current situation.

VIDEO IN

AUDIO

IN

SPOT VIDEO OUT

SPOT AUDIO OUT

VIDEO IN SLAVE VIDEO OUT

•While using the SETUP Menu•While displaying the Event List or the Door Bell List•While replaying events•While zooming-in the screen•While setting a still screen on the multi screen mode

3.When you want to watch in Full Screen Mode

If you are on a split screen, move to your desired channel using the Rotary Wheel and press ENTER. The selected channel will be displayed in full screen mode. At this time, you can change the channel using the Rotary Wheel.

In addition, you can change the channel by pressing number buttons on your remote control.

Chapter 4: Basic Operation

1.Basic Operation

1)Turn the Power Switch On.

When turned on for the first time, the 9-split screens are displayed on the monitor. At this time, the channels that have no input are displayed with a blue screen and video loss occurs.(After complet- ing the initial setup, the settings are memorized when the power is turned off. Therefore, when you turn the power on again, the prod- uct will be operated with the previous settings.)

2)Select a Display Mode as follows.

•Full Screen Mode: When you are on a split screen, move to your desired channel using the Rotary Wheel and press the ENTER button located at its center. The selected channel will then be dis- played in Full Screen Mode.

•Multi Screen Mode: Press the MULTISCREEN button to display the split screens. You can select which channels will be displayed on the split screen.

•Sequence Screen Mode: Press the SEQUENCE button. Channels are automatically switched sequentially in full screen mode.

•Freeze Screen Mode: You can capture and view a still screen using the FREEZE button and the Rotary Wheel.

•LIVE/P.B. Screen Mode: You can monitor the present camera signals or playback the recorded screens using the LIVE/P.B./TRIPLEX button.

•TRIPLEX Screen Mode: Watch the present camera signals and recorded screens on the same monitor using the LIVE/P.B./TRIPLEX button.

•PIP Screen Mode: You can watch Picture in Picture (PIP) screens by using the PIP button.

•Zoom Screen Mode: You can enlarge a full screen two times using the Zoom button and Rotary Wheel.

2.When you want to watch on

LIVE/P.B./TRIPLEX screen.

Select the LIVE, P.B., or TRIPLEX screen mode using the LIVE/P.B./TRIPLEX button.

Each press of this button changes the screen mode to LIVE mode, P.B. mode, and TRIPLEX mode sequentially.

The LIVE/P.B./TRIPLEX button will not operate in the following cases:

4. When you want to watch in Sequence Screen Mode

The Sequence screen is available only in full-screen LIVE mode. Press the SEQUENCE button when the screen is in full-screen LIVE mode to switch to the Sequence screen. You can set the switching intervals by going to "SEQUENCE" under "4. SYSTEM SETTING" on the SETUP MENU. The range of switching intervals is from one to thirty seconds. Press the SEQUENCE button again to stop the screen displayed at the present time.

The SEQUENCE button will not operate in the following cases:•While operating in P.B. or TRIPLEX mode

•While using the SETUP Menu

•While displaying a split screen•While displaying the Event List or Door Bell List

•While replaying events

•While zooming-in the screen

5.When you want to watch in FREEZE Screen Mode

You can stop a full or split screen temporarily and view the still screen in LIVE, P.B., TRIPLEX mode.

You can select and stop the channels you wish to stop in split screen mode.1)Full Screen Display

If the FREEZE button is pressed, the current display will freeze, and the FREEZE icon will appear in the upper right corner of the screen. Press the FREEZE button again to exit this mode.

2)Multi-Screen Display

!If the FREEZE button is pressed, the FREEZE icon will appear in the upper right corner of the screen.

@Move to the picture you would like to freeze by using Rotary Wheel.

#By pressing the ENTER button in the middle of Rotary Wheel, the picture from that channel will freeze, and the character “F” will appear. Press the ENTER button again to exit this mode.

$If you would like to see the frozen picture from another chan- nel, move to the target channel, and press ENTER.

Eng-7