Hint
Hint
• To go back one step, press the sbutton
(during the steps [2] to [7].)
•
Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint
Hint
• If you accidentally select Spanish or
French and need English:Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE.Press
theBbutton, and select ENGLISH. Finally,
press the CLEAR/C.RESET button.
–12 –EN
Setup
2
2
LANGUAGE SELECT
BENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1
1
Turnon the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel”section.
POWER
3
3CH 01
AUTOSET UP
ToPreset the Channel Again
1)Press the MENU button until the main
menu appears.
2)Select "CHANNEL SET UP" by pressing
theKor Lbutton. Then, press the Bbut-
ton.
3)Select "AUTO SET UP" by pressing the
KorLbutton. Then, press the Bbutton.
After scanning, the tuner stops on the low-
est memorized channel.
ToChange the On-Screen Language
1)Press the MENU button until the main
menu appears.
2)Select "LANGUAGE SELECT" by press-
ing the KorLbutton. Then, press the B
button.
3)Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" bypressing the Kor Lbut-
ton.Then, press the CLEAR/C.RESET
button.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using the SKIP/CH.
(K/L) buttons.
•If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the Bbutton once again.
Y
Yes
es Press the MENU
button to exit
• Refer to “Hint for Cable Box
or Satellite Box”section on
page 8.
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?
YES
NO
Turn on the unit for the first
time
TV ScreenRemote Control
Clock Set Up
ToSelect a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example:117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
VCR
VCR
Preparation for Use
5
5
4
4CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
6
6CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7
7CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P MAM
BPM
Select the current year
Select “AM”or “PM”
8
8 Toexit the CLOCK SET
screen.
Select the current hour
Select the current minute
or
or
or
or
or
VCR
1
1-MENU-
TIMER PROGRAMMING
AUTOREPEAT [OFF]
CHANNEL SET UP
BCLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
2
2CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3
3CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
Select the current day
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button.In this
case, go to step [2].
VCR
VCR
or
or
or
VCR