MODEL: MX-B201D

DIGITAL MULTIFUNCTIONAL SYSTEM

START GUIDE

This guide explains how to install the machine, and indicates important points to note for installation and usage. Read and understand this guide to ensure that you install the machine correctly. The Operation Guide for the machine is on the accompanying CD-ROM. The procedure for viewing the guide is explained in "4. HOW TO USE THE OPERATION GUIDE". After installation, read the Operation Guide to make full use of all the machine has to offer.

1. TONER CARTRIDGE REPLACEMENT
2. LOADING PAPER

1

Raise the handle of the paper tray and

2

Rotate the pressure plate lock in the direction

3

Store the pressure plate lock which has been

pull the paper tray out until it stops.

of the arrow to remove it while pressing down

removed in step 2. To store the pressure plate

 

 

 

the pressure plate of the paper tray.

 

lock, rotate the lock to fix it on the relevant

 

 

 

 

 

location.

When toner is low, the error indicator will light up and "TONER CARTRIDGE IS NEAR EMPTY." will appear in the display to alert you to purchase a new toner cartridge. on purchasing a new toner cartridge. If copying is continued while the indicator is lit, copies will gradually become lighter until the toner runs out. When the toner runs out, the machine will stop operating, the error indicator will blink, and "REPLACE THE TONER CARTRIDGE" will appear in the display. Follow the procedure below to replace the toner cartridge.

• After the machine stops, it may be possible to make a few more copies by taking the toner cartridge out of the machine, shaking it horizontally, then reinstalling it. If copying is not possible after this operation, replace the toner cartridge.

•During a long copy run of a dark original, "TONER REPLENISHMENT IN PROGRESS" appears in the display, and the machine may stop even

though toner is left. The machine will feed toner up to 2 minutes and then the ready indicator will light up. Press the [START] key ( ) to resume copying.

1

Open the bypass tray, and then

2

Push gently on both sides of the

3

Gently pull the toner cartridge out while pressing the lock

open the side cover while pressing

front cover to open the cover.

release lever.

the side cover open button.

Toner cartridge lock release lever

 

• After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge.

• Dispose of the old toner cartridge in accordance with local regulations.

4

Squeeze the lever of paper guide (A) and slide

the guide to match with the width of the paper.

Move paper guide (B) to the appropriate slot as marked on the tray.

(B)

(A)

 

5

Fan the paper and insert it into the tray.

6

Gently push the paper tray back into the unit.

Make sure the edges go under the

 

corner hooks.

• Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges.

• Make sure all the paper in the stack is the same size and type.

• When loading paper, ensure there is no space between the paper and the guide, and check if the guide is not set too narrow causing the paper to bend. Loading paper in these ways will result in document skew or a paper jam.

4

Remove the toner cartridge from the bag.

5

Gently insert the toner cartridge along the

6

Close the front cover and then the side

Grasp the cartridge on both sides and shake

guides until it locks in place while pushing

cover by pressing the round projections

 

it horizontally four or five times. After

 

the lock release lever.

 

near the side cover open button. The error

 

shaking the cartridge, remove the toner

 

Remove the tape from the shutter. Pull the

 

indicator will go out and the ready indicator

 

seal.

 

shutter out of the toner cartridge as shown

 

will light up.

 

 

 

in the illustration. Discard the shutter.

 

 

4 or 5 times

Shutter

Toner seal

3. POWER ON AND OFF

If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result.

1 Turn the power switch on the left side of the unit to the "ON" position.

2 Ensure that the power switch of the unit is in the OFF position.

ON

OFF

The ready indicator will light up and other indicators which show the

If the power switch is turned off while the machine is in operation, a

initial settings of the display will also light up to indicate the ready

misfeed may occur and the job that was in progress will be canceled. In

condition. For the initial settings, see "Initial settings" on the Operation

cases where the machine will not be used for a long time, turn off the

Guide.

power switch and remove the power cord from the outlet.

About the scan head

Grasp the toner cartridge as shown in the illustration. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the toner seal is removed.

When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.

Even after a new toner cartridge is installed, the start ( ) indicator may not light up, indicating copying cannot be restarted (toner is not sufficiently fed). In this case, open and close the side cover. The copier will feed toner again approximately 2 minutes and then copying can be restarted.

The scan head lamp remains on constantly when the unit is in the ready condition (when the start ( ) indicator is illuminated).

The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble.

4. HOW TO USE THE OPERATION GUIDE

Detailed explanations of the functions that can be used on the machine are provided in the Operation Guide in PDF format.

1

Insert the supplied CD-ROM into your

2

Display the contents of the CD-ROM, and open

* To view the Operation Guide in PDF format,

computer's CD-ROM drive.

the Operation Guide file.

 

 

 

 

 

 

 

 

 

 

 

 

Adobe® Reader® or Acrobat® Reader® of

 

 

 

 

 

 

 

 

 

 

 

 

Adobe Systems Incorporated is required.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operation Guide file (PDF)

Adobe® Reader® can be downloaded from the

 

 

 

 

 

 

 

 

 

 

Manual English

following URL:

 

 

 

 

 

 

 

 

 

 

http://www.adobe.com/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operation Guide CD-ROM

PRINTED IN CHINA 2010L KS1 TINSE2155QSZZ