Sharp PG-LW3000, PG-LW3500, PG-LX3000, PG-LX3500, PGLX3500 Resetting the Lamp Timer

Regarding the Lamp (Continued)

4	Remove the lamp unit.	Securing
	• Loosen the securing screw from the lamp	screw
	unit. Hold the lamp unit and pull it in the	screw
	unit. Hold the lamp unit and pull it in the
	direction of the arrow. At this time, keep
	the lamp unit horizontal and do not tilt it.

5	Insert the new lamp unit.
	• Press the lamp unit firmly into the lamp unit
	compartment to align the lamp connectors.
	Fasten the securing screw.

6	Replace the lamp unit cover.
	• Slide the lamp unit cover horizontally back
	into place and align the tabs (1). Then
	tighten the user service screw (2) to
	secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

1		Connect the power cord.		AC socket
		• Plug the power cord into the AC socket of
		the projector.
2		Reset the lamp timer.
2		Reset the lamp timer.
		• While simultaneously holding down
		MENU, ENTER and R on the projector,
		MENU, ENTER and R on the projector,
		press STANDBY/ON on the projector and
		keep all four buttons pressed down until
		the lamp indicator starts blinking green.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

STANDBY/ON button

ENTER button

MENU button

Rbutton

Appendix

65

Contents

MODEL Model No.: Serial No.: ENGLISH INFORMATION PRODUCT DISPOSAL Caution Concerning Lamp Replacement Caution Supplied accessories Preparing Introduction Easy Start Setup Connections Reference CAUTION: Page Observe the following safeguards when setting up your projector Info Page Page Page Inserting the Batteries Caution Usable Range Setup and Projection 1. Place the projector facing a wall or a screen 3. Turn the projector on 6. Select the Input mode 5. Correct trapezoidal distortion 4. Adjust the projected image with the Setup Guide 7.Turn the computer on 8.Turn the power off Video Setup Setting Up the Projector Standard Setup (Front Projection) Indication of the Projection Image Size and Projection Distance [PG-LW3000/PG-LW3500] Screen Size and Projection Distance Screen Size and Projection Distance (Continued) Projection (PRJ) Mode aCeiling-MountSetup Terminals on the Projector Connecting the Projector to Other Equipment (Continued) Page Page Page Turning the Projector On Turning the Power Off (Putting the Projector into Standby Mode) Basic Operation About the Setup Guide Adjusting the Projected Image 1 Adjusting the Focus 2 Adjusting the Height 3 Adjusting the Picture Size Correcting Trapezoidal Distortion Switching the Input Mode Adjusting the Volume Displaying the Black Screen and Turning Off the Sound Temporarily Resize Mode About Copyrights Page Page Displaying the Pointer Displaying and Setting the Break Timer Using the Spot Function Switching the Eco+Quiet Mode Auto Sync (Auto Sync Adjustment) Freezing a Moving Image Selecting the Picture Mode Displaying an Enlarged Portion of an Image Page Page Page Menu Selections (Quick Start Menu) Quick Start Menu To adjust the projected image while watching it 1Selecting the Picture Mode 2Adjusting the Image 3Adjusting the Color Temperature 4Adjusting the Colors 5Selecting the Film Mode 7Eco+Quiet 6Reducing Image Noise (DNR) 2Resolution Setting 3Signal Type Setting 5Setting the Video System 6Setting the Video Setup 7Checking the Input Signal 1Setting the Resize Mode 3Keystone Correction 2Adjusting the Image Position 4Setting the Overscan 5Setting the On-screenDisplay 6Closed Caption 7Selecting the Background Image 8Selecting the Setup Guide 9Reversing/Inverting Projected Images 0Selecting the Wall Color 1Auto Sync (Auto Sync Adjustment) 2Auto Power Off Function 3Auto Restart Function 4Speaker Setting 5Fan Mode Setting 6 System Lock Function 7Keylock Function 8Selecting the Quick Start Menu 9COMPUTER2 Select 0Setting the FUNCTION Button Operation STANDBY Mode STANDBY Audio Out DLP® LinkTM DLP® LinkTM Invert Setting Up the Projector Network Environment (“Network” Menu) 1 Setting a Password 2DHCP Client Setting 3TCP/IP Setting 4Returning to Default Settings (Network) 5Restart Network Function 6Confirming the Projector Information Precautions on Viewing Stereoscopic 3D Images WARNING Information on the 3D Projection Function Using 3D Viewing Mode Warning Projecting 3D images Ending 3D projection Page Page Page Lamp Caution Concerning the Lamp Replacing the Lamp Removing and Installing the Lamp Unit Resetting the Lamp Timer Page Page Page Page Page Page Page Units: inches (mm)