Sherbourn Technologies, Inc.
Owner’s Manual
39
Owner’s Manual
4. Point the remote control toward the device that was turned on in
Step 1 and press in the rst three-digit setup code number for that
device using the number buttons (0-9) on the remote control.
The LED and selected Source button will blink and then stay lit after
you enter a setup code.
Your device will turn off when the correct setup code number has been
selected. If the device does not turn off, press in the next setup code
number from the listing. The remote will remain in this program-
ming mode as long as you continue to enter codes within 10 seconds
of each other.
Continue entering setup code numbers until your device turns off, then
proceed to Step 5.
Note: If you have tried all of the three digit setup code numbers
listed for your device and it still did not turn off, please proceed to
the Auto Search Method below to program your remote control.
5. Once your device turns off, press the Device Button selected in Step
3 once again to store the setup code number.
The LED and Source button will blink twice and then go out.
6. Test the remote control for your device. Try the POWER, CHANNEL
UP and DOWN, VOLUME UP and DOWN buttons, etc.
If any of the buttons do not perform as they should, please repeat the
setup from Step 1 using the next setup code number for your device.
Note: Some audio/video devices have separate buttons for
POWER ON and POWER OFF. To operate these devices on the
remote, press the corresponding Source button to turn the equip-
ment ON and press the POWER button to turn the equipment OFF.
7. Please repeat the above steps to program the remote control for
each of your other devices.
If none of the setup code numbers worked for your device during the standard
setup procedure, or if the manufacturer or brand for your device is not listed
in Setup Code Tables, use the steps below.
To program using Auto Search
1. Turn on the device you would like the remote control to operate,
either manually or with its original remote control.
3. Press the corresponding Source button and the MUTE button on
the remote control simultaneously.
The red LED and the selected Source button will illuminate.
Note: The selected button and LED will remain for approximately
10 seconds to indicate that the remote control is ready to be pro-
grammed. The following steps must be entered while they are lit.
If the lights go out, simply press the Source and MUT button again
to re-enter the setup code.
3. Point the remote control toward the device and press the CHANNEL
UP button on the remote control.
Each press of the CHANNEL UP button sends the signal for one setup code
number. The LED and Source button will blink each time you press the
CHANNEL UP button. Keeping the CHANNEL UP button pressed quickly
scans through the setup code numbers.
Release the CHANNEL UP button as soon as the device turns off. Con-
rm that you have the correct code by pressing the MUTE button on
the remote. You should be able to turn your device on and off with this
button.
If you pass the correct setup code number, you can return to it by pressing
the CHANNEL DOWN button, one number at a time, until your device
turns back on.
Note: During programming, the signal for POWER ON and POWER
OFF is located on the MUTE button. For devices that use separate
POWER ON and POWER OFF buttons, pressing the MUTE button on
the remote control during programming will only turn the device
OFF.
4. Once the correct code is conrmed, press the Source button to store
the setup code number.
The LED and Source button will blink twice and then go out.
5. Test the remote control for your device. Try the POWER, CHANNEL
UP and DOWN, VOLUME UP and DOWN buttons, etc.
If any of the buttons do not perform as they should, please repeat the
setup from Step 1 using the next setup code number for your device.
Note: Some audio/video devices have separate buttons for
POWER ON and POWER OFF. To operate these devices on the
remote, press the corresponding DEVICE Button to turn the equip-
ment ON and press the POWER button to turn the equipment OFF.
6. Please repeat the above steps to program the remote control for
each of your other devices.
To display the stored three digit setup code number for a device:
1. Press the corresponding Source button and the MUTE button on
the remote control simultaneously.
The red LED and the selected Source button will illuminate.
2. Press the T/V button.
The LED and Source button will quickly ash the three digit setup code
number, pausing between numerals, that was stored for your device in
that mode. The number zero (0) is indicated by ten ashes.
3. Please write your setup code numbers in the chart below, for future
reference.
Set-Up Code Numbers:
Remote Control Setup and Operation
38