Sierra Monitor Corporation PSE530 manual

20mm or more

Connector cover

Pressure Sensor

Operation Manual

PSE530 Series

Thank you for purchasing the SMC PSE530 Series Pressure Sensor.

Please read this manual carefully before operating pressure sensor and understand pressure sensor, its capabilities and limitations. Please keep this manual handy for future reference.

URL http://www.smcworld.com

Installation (addendum information)

Attaching the connector to the lead wire

・Sensor wire is stripped as shown in the right figure.・The Insulation of the corresponding color shown in the following table is

put into the pin of the number stamped			Insulation
on the connector for sensor connection to the bottom.
Pin No.	Color of Insulation
1	Brown (DC (+) )
2	N.C.
3	Blue (DC (-) )
4	Black (IN:1 to 5VDC)		A
		2	1
・It checks that the above-mentioned preparation
		3
		4

work has been performed correctly, and A part shown in right figure is pushed by hand and makes temporary connection.

・A part center is straightly pushed in by tools, such as pliers.

・Re-use cannot be performed once it connects the connector for sensor connection completely.

・A sensor connector cannot be taken apart for reuse once it is crimped.If the wire arrangement is incorrect or if the wire insertion fails,

use a new sensor connector. 1 2 34・When connecting the connector to

PSE200/PSE300 series, please use
the connector for Sensor Lead Wire(ZS-28-C) or		as below.
Maker	Model No.
(c)Sumitomo 3M	37104-3101-000FL
Tyco Electronics AMP	3-1473562-4
OMRON	XN2A-1430

・Please contact with each connector maker about catalogue.

Connector

Connector Connecting / Disconnecting

・When connecting the connector, insert it straight onto the pin holding the lever and connector body between fingers and lock the connector by pushing the lever claw into the square groove in the housing until connector clicks.

・When disconnecting the connector, push down the lever by thumb to disengage the lever claw from the square groove. Then pull the connector straight out.

PSE200 Series PSE300 Series

						Lever
	Lever			Connector for Sensor
				Lead Wire
Example of Internal Circuit and Wiring
Output Specification
Voltage output :				Brown DC (+)
1 to 5V		circuit	1kΩ
Output impedance :				Black OUT
Approx. 1kΩ		Main		(Analog output)	-	DC
					+	12 to 24V
				Blue DC (-)

Outline with Dimensions (in mm)

PSE53	-M5
3.4						M5	0.8
				29.4		Pressure port
				27.2			2	.	5
									13
5.4			12	7.2
					3		12
					4
				5	5.5
PSE53	- R06
	R07
				45.5			Pressure port
3.4				43.3
5.4			12	7.2			D
	Model No.			Applicable port size(D)
	PSE53	-R06		6mm
	PSE53	-R07		1/4inch
When connect cable for sensor
				9.8
		10.4	2.7

SAFETY

The Pressure Sensor and this manual contain essential information for the protection of users and others from possible injury and property damage and to ensure correct handling.

Please check that you fully understand the definition of the following messages (signs) before going on to read the text, and always follow the instructions.

IMPORTANT MESSAGES

Read this manual and follow its instructions. Signal words such as WARNING and NOTE will be followed by important safety information that must be carefully reviewed.

Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions.

WARNING

Do not disassemble, remodel ( including change of printed circuit board ) or repair.

An injury or failure can result.Do not operate beyond specification range.Fire, malfunction or sensor damage can result.Do not operate in a combustible gas or explosive gas atmosphere.Fire or an explosion can result.This pressure sensor is not an explosion proof type.

OPERATOR

●This operation manual has been written for those who have knowledge of machinery and apparatus that use pneumatic equipment and have full knowledge of assembly, operation and maintenance of such equipment.

●Please read this operation manual carefully and understand it before assembling, operating or providing maintenance service to the pressure sensor.

NOTE

Follow the instructions given below when handling your pressure sensor. Otherwise, the sensor may be damaged or may fail, thereby resulting in malfunction.

・Do not drop it, bring it into collision with other objects or apply excessive shock (980m/s2 or more).

・Do not pull the lead wire with force nor lift the main unit by holding the lead wire. (Pulling strength less than 23N)

・Do not insert wire nor other article into the pressure port. ・Perform wiring and cable correctly.

・Do not perform wire or cable while power is on.・Do not wire with the same circuit of power line or high-voltage line.

・Connect Terminal FG to the ground when using a switching regulator obtained on the commercial market.

・Keeping from water and dust, set an air tube to the safety area.

How to connect the cable for sensor.(Optional)

Pick with fingers the hemale connector of cable for sensor. Insert it paying attention of connector direction.

SensorMale connectorFemale connector

Cable for sensor have connector cover in order to prevent fall of female connector. Paying attention for connector cover direction, install on the sensor, rotate clockwise, and lock it.

To remove cable for sensor, rotate the connector cover anti- clockwise, relese lock, and remove connector cover.

After removing connector cover, pick with female connector with fingers and pull out.

Lock

Sensor

Connector cover

Unlock

Specification

Model No.			PSE530-※	PSE531-※	PSE532-※	PSE533-※
Rated pressure range			0 to 101MPa	0 to -101kPa	0 to 101kPa	-101 to 101kPa
Withstand pressure			1.5MPa		500kPa
Fluid			Air, Non-corrosive gases, Incombustible gases
Power supply			12 to 24VDC, ripple(p-p)10% or less (Protection against inverse connection)
Current consumption				15mA or less
Analog		Voltage	Voltage: 1 to 5V±2%F.S. or less (Rated pressure range)
output		output	Linearity : ±1%F.S. or less Output impedance : Approx.1kΩ
Repeatability				±1%F.S. or less
Effect form power supply			±1%F.S. or less with standard of analog output at 18V in the range of 12 to 24VDC
Temperature Characteristic			±2%F.S. or less (25℃ reference）
	Enclosure			IP40
Environment	Ambiebt temperature		Operation : 0 to 50℃,Storage :-10 to 70℃ (No condensation, No freezing)
	Withstand voltage		10 to 500Hz smaller one 1.5mm or 98m/s2		double amplitude, 2 hours each in direction
			1000VAC, 50/60Hz, 1minute (Between lead block and case)
	Insulation resistance		5MΩ or more 500VDC (Between lead block and case)
	Vibration proof			of X, Y and Z
	Impact proof		980m/s2 3times each in directions of X ,Y and Z respectively
Standard				CE MARKING
Cable			Halogen free heavy insulation cable, φ2.7, 0.15mm2, 3wire, 3m

Piping Specification

Model No.		M5	R06		R07
Port size		M5×0.8	φ6 Reducer		1/4inch Reducer
Material		Sensor pressure sensing part : Silicon O-ring : NBR
		Body : SUS303	Body : PBT
Weight	With cable(3m)	41g		38g
	Excluding cable	7g		3.8g