3-862-454-15(1)

English

 

 

Español

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC Adaptor/Charger

Operating Instructions
Manual de instrucciones
Mode d’emploi

CS

AC-V700

Sony Corporation © 1998 Printed in JapanOwner’s Record

The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. AC-V700 Serial No.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.

This symbol is intended to alert the user to the presence of uninsulated “Dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The Graphical Symbols with Supplemental Marking is located on the bottom of the unit.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362, (i.e., marked with 2 or @ mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

A

1

 

 

5

 

 

 

2

 

 

6

 

 

 

3

 

 

 

 

 

 

7

 

 

 

8

4

 

 

9

 

 

 

 

 

 

 

 

!∞

WARNINGVCR/CAMERA

 

BATTERY LIFE

!™

TIME TO CHG

 

 

NORMAL FULLh m

 

 

 

 

 

B

3

2

4

1

1

To removePara extraer

2

To remove

Para extraer

C

1 2

3

b

1

c

d

2

e

f

Before operating the unit, please read this manual thoroughly and retain it for future reference.

The AC-V700 AC adaptor/charger can be used as follows:

To charge a lithium ion type battery pack. Ni-Cd/Nickel hydrogen type batteries are not rechargeable.

The following functions are available with the “InfoLITHIUM” battery pack:Quickly chargingRemaining charge time display

To enable the power supply to the video equipment with the house current, connection cords are included with this unit. However, these cords may not be used depending on the video equipment. Before using, check your video equipment.

What is the “InfoLITHIUM”

The “InfoLITHIUM” is a lithium ion battery pack which can exchange data with compatible video equipment about its battery consumption. Sony recommends that you use the “InfoLITHIUM” battery pack with video

equipment having themark.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.To avoid electrical shock, do not open the cabinet.Refer servicing to qualified personnel only.AC power cord must be changed only at the qualified service shop.For the customers in CanadaCAUTIONTO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Notes on Use
About the AC power cord plug

The AC-V700 comes in two models, differentiated by the shape of the AC power cord plug.

ModelShape of the plug
Model for USA/CanadaPolarized
Model for other countriesNon polarized

The model for USA and Canada: One blade of the plug is wider than the other for the purpose of safety and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

About the remaining battery time

While charging the battery pack, this unit will show the remaining battery time with your video equipment, etc. on the following conditions.

Using the “InfoLITHIUM” battery packUsing the video equipment having the mark

Make sure that you use the battery pack having the mark. Consult the operating instructions supplied with your video equipment if it is applied to “InfoLITHIUM”.

Though the following models are applied to “InfoLITHIUM”, the remaining battery time is not displayed on this unit.

DCR- PC7/PC7E/PC10/PC10E/SC100/SC100E/TRV7/TRV7E

CCD- TR555/TR555E/TR610E/TR710/TR710E/TR760E/TR790E/TR810E/ TR820E/TR825E/TR910/TR910E/TR920E/TR930/TR1100E/ TR2200E/TR2300/TR2300E/TR3100E/TR3300/TR3300E/TR3400/ TRV31/TRV31E/TRV41/TRV41E/TRV51/TRV51E/TRV54E/ TRV56E/TRV61E/TRV62/TRV64E/TRV72/TRV81/TRV81E/ TRV82/TRV91E/TRV94/TRV94E/TRV101/TRV101E/ SC55/SC55E/SC65/SC65E

GV-A500/A500E

If you use the video equipment having the mark, the remaining battery time display of the battery pack being charged corresponds to the video equipment

having the mark which is last attached to the battery pack.

Charging

Use only a lithium ion type battery pack. This unit cannot be used to charge a Ni-Cd/Nickel hydrogen type battery pack.

Attach the battery pack firmly.Charge the battery pack on a flat surface without vibration.Charging temperature

The temperature range for charging is 0°C to 40°C (32°F to 104°F). However, to provide maximum battery efficiency, the recommended temperature range when charging is 10°C to 30°C (50°F to 86°F).

Others

The nameplate indicating operating voltage, power consumption, etc. is located on the bottom.

The negligible amount of electric current will flow into the AC adaptor/ charger as long as the AC adaptor/charger is plugged into the wall outlet.

Unplug the unit from the wall outlet if it will not be used for extended period of time. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

Do not operate the unit with a damaged cord or if it has been dropped or damaged.

Be sure that nothing metallic comes into contact with the metal parts of the unit or connecting plate. If it does, a short may occur and the unit may be damaged.

Always keep the metal contacts clean.Do not disassemble or convert the unit.Do not apply mechanical shock or drop the unit.While the unit is in use, it gets warm. But this is normal.Keep the unit away from AM receivers, because it will disturb AM reception.Do not place the unit in a location where it is:Extremely hot or coldDusty or dirtyVery humidVibrating

If any difficulty should arise, unplug the unit and contact your nearest Sony dealer.

Specifications
Power requirements100 - 240 V AC, 50/60 Hz
Power consumption

25 W

 

Charge mode:

 

35 VA (100 V AC), 46 VA (240 V AC)

 

Operating mode:

 

39 VA (100 V AC), 50 VA (240 V AC)
Output voltageDC OUT:

 

8.4 V, 2.0 A in operating mode

 

Battery charge terminal:

 

8.4 V, 1.4 A in charge mode
ApplicationSony battery pack NP-F100/F200/F300/F330/

 

F530/CF540/F550/F730/F750/F930/F950
Operating temperature0°C to 40°C (32°F to 104°F)
Storage temperature–20°C to 60°C (–4°F to 140°F)
DimensionsApprox. 127 ⋅ 55 ⋅ 95 mm (w/h/d)

 

(5 ⋅ 2 3/16 ⋅ 3 3/4 inches)
MassApprox. 255 g (9 oz)
Supplied accessoryConnecting cord DK-415 (1),

 

AC power cord (1)
Design and specifications are subject to change without notice.

Use a commercially available AC plug adaptor, if necessary, depending on the design of the wall outlet.

Wall outletAC-V700AC plug adaptor

This mark indicates that this product is a genuine accessory for Sony video products. When purchasing Sony video products, Sony recommends that you purchase accessories with this “GENUINE VIDEO ACCESSORIES” mark.

Identifying the parts
See illustration A.1Terminal shutter2 Charging polarity3 Battery release lever4 DC OUT connector5 Guide6 CHARGE lamp7 Mode change switch8 DISPLAY CHANGE button9 Display windowDisplay window“InfoLITHIUM” indicatorLights up when the “InfoLITHIUM” battery pack is attached.WARNING indicator!™ TIME TO CHG (charge) indicator Time indicatorBATTERY LIFE (battery remaining time) indicator !∞ VCR/CAMERA indicatorFull charge indicatorRemaining battery indicator
To Charge the Battery Pack
See illustration B.1Set the mode change switch to CHARGE.2Connect the power cord to this unit.3Connect the power cord to a wall outlet.The beep sounds and the display window lights up.4Install the battery pack.

Charging begins. When the remaining battery indicator becomes and the CHARGE lamp lights up, normal charge is completed. For full charge, which allows you to use the battery slightly longer than “normal charge”, leave the battery pack attached until the CHARGE lamp goes out.

Remove the battery pack when required. It can be used even if the charging is not completed.

Remaining battery indicator
Normal chargeFull charge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To Install the battery packNP-F550, etc. (ill. B-1)1Place the battery pack on a.

Align the end of the battery pack having the 4 mark with the edge of the terminal shutter of this unit.

a folds down when the battery pack is placed on it.2Slide the battery pack in the direction of the arrow.Press the battery pack until the terminal shutter is completely covered.NP-F100, etc. (ill. B-2)1Slide the battery pack along the guide to a.2 Press the battery pack down until it clicks.Note

Do not apply shock to the charging polarity. When you install the battery pack, be sure to not strike it.

Charging time

The following table shows the charging time for the battery pack which is discharged completely.

Battery packCharging time

Battery pack

Charging time

 

 

 

 

 

NP-CF540

110 (50)

 

NP-F100

100 (40)

 

 

 

 

 

NP-F550

115 (55)

 

NP-F200

115 (55)

 

 

 

 

 

NP-F750

170 (110)

 

NP-F300

160 (100)

 

 

 

 

 

NP-F950

225 (165)

 

 

 

 

 

 

 

 

Approximate minutes to charge an empty battery pack fully (Full charge).

Approximate minutes in parentheses indicate the time when you charge normally (Normal charge).

To ascertain the battery life, refer to the instruction manual of the video equipment which you use.

The charging time may differ depending on the condition of the battery pack or the temperature of the environment.

Notes

When the mode change switch is set to VCR/CAMERA during charging, charging stops.

When a fully charged battery pack is installed, the CHARGE lamp will once light, then go out.

If the CHARGE lamp does not light or flash, check that the battery pack is correctly attached to the AC adaptor/charger. If it is not attached it will not be charged.

When the CHARGE lamp flashes

If a problem occurs during charging, the CHARGE lamp flashes and WARNING appears on the display.

Check through the following chart.

Remove the battery pack from this unit, then install the same battery pack again.

If the CHARGE lamp flashes

 

If the CHARGE lamp lights and
again:

 

does not flash again:
Install another battery pack.

 

If the CHARGE lamp goes out

 

 

 

because the charging time has

 

 

 

 

 

passed, there is no problem.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the CHARGE lamp flashes

 

If the CHARGE lamp lights and

again:

 

does not flash again:

The problem is with this unit.

 

If the CHARGE lamp goes out

 

 

 

because the charging time has

 

 

 

 

 

passed, the problem is with the

 

 

 

battery pack first installed.

 

 

 

 

 

 

 

 

 

 

Please contact your nearest Sony dealer in connection with the product with the problem.

To remove the battery pack

NP-F550, etc. (ill. B-1)

Slide the battery pack in the direction of the arrow, then lift is straight out.

NP-F100, etc. (ill. B-2)

Remove the battery pack while sliding the battery release lever.To Check Charging

While charging, you can check the charging time on the display. After starting charging in a minute, BATTERY LIFE lights up on the display.

Press DISPLAY CHANGE while charging.Each time you press DISPLAY CHANGE, the display changes as follows.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The remaining battery time

 

BATTERY LIFE

when the battery pack being

 

 

 

 

 

 

 

 

m

 

 

 

 

charged is attached to your

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“InfoLITHIUM” video equipment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DISPLAY

The time is not displayed when the

 

 

 

remaining battery time is less than 5

 

 

 

CHANGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minutes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The remaining time until

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

normal charge is completed

TIME TO CHG

 

 

 

 

 

 

 

 

 

 

 

 

 

• The normal charge time is not

 

 

 

 

 

 

 

 

 

 

 

 

 

NORMAL

 

 

 

 

 

 

 

m

 

 

 

 

 

displayed after the normal charge is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

completed.

 

 

 

DISPLAY

 

 

 

CHANGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The remaining time until full

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIME TO CHG

 

 

 

 

 

 

 

 

 

 

 

 

 

charge is completed

 

h

 

 

 

 

 

m

 

 

 

 

 

• The full charge time is not displayed

 

 

 

 

 

 

 

 

 

 

 

FULL

 

 

 

 

 

 

 

 

 

after the full charge is completed.

 

 

 

 

 

 

 

 

 

DISPLAY

CHANGE

Notes

The time display shows the approximate time when charging at 10°C - 30°C. The time display may differ from the actual charging time depending on using conditions and circumstances.

The time display may show “– – – –” in the following cases. However, the unit is not malfunctioning.

The remaining battery time is less than 5 minutes.

There is a difference between the displayed time and actual charging time. Even if this happens, continue charging.

Full charge requires about 1 hour after normal charge is completed. If you remove the battery pack between normal charge and full charge, the charging time may not be displayed properly in the next charging.

If the charging time is not displayed properly, fully charge the battery pack. The charging time will be displayed properly.

When you attach a fully charged battery pack to this unit, “TIME TO CHG FULL 1h” may appear on the display. However, the unit is not malfunctioning.

BATTERY LIFE may not be displayed depending on using conditions and circumstances.

You may wait for a while after pressing DISPLAY CHANGE until the display shows the time indication.

To Operate Video Equipment
See illustration C.

For the DCR-TRV9 video camera, etc., use the supplied DK-415 connecting cord. For the DCR-PC10 video camera, etc., use the DK-626 connecting cord (not supplied).

For details of the connection, refer to the instruction manual of the video equipment.

1Set the mode change switch to VCR/CAMERA.2Connect the power cord to a wall outlet.3Connect the connecting cord b to the DC OUT connector of this unit.4Connect the connecting cord to the video equipment. DCR-TRV9, etc. (ill. C-1)While pressing the connecting plate c , slide it down.

To remove the connecting plate, slide it up while pressing the battery release lever d.

DCR-PC10, etc. (ill. C-2)Open the cover, and insert the connecting plug e.To remove the connecting plug, pull it while pressing the button f.

Notes

If you set the mode change switch to CHARGE while operating the video equipment, the power supply to the video equipment stops.

You cannot charge the battery pack attached to this unit while supplying the power to the video equipment.

Keep this unit away from the video equipment if the picture is disturbed.

Antes de utilizar la unidad, lea detenidamente este manual, y consérvelo para futuras referencias.

El adaptador de CA/cargador AC-V700 podrá utilizarse de la forma siguiente:

Para cargar una batería de tipo iones de litio. Las pilas de tipo níquel- cadmio/níquel-hidrógeno no podrán recargarse.

Cuando utilice una batería “InfoLITHIUM”, estarán disponibles las funciones siguientes:

Carga rápidaVisualización del tiempo de carga restante

Con esta unidad se incluyen cables conectores para poder alimentar equipos de vídeo con la corriente de la red. Sin embargo, quizás no pueda utilizar estos cables dependiendo del equipo de vídeo. Antes de utilizarlos, compruebe su equipo de vídeo.

Qué es “InfoLITHIUM”

La batería “InfoLITHIUM” es una batería que purde intercambiar datos con un equipo de vídeo compatible en cuanto a su consumo de batería. Sony recomienda que utilice la batería “InfoLITHIUM” con equipos de vídeo que

posean la marca .
ADVERTENCIA

Para evitar incendios o el riesgo de electrocución, no exponga la unidad a la lluvia ni a la humedad.

Para evitar descargas eléctricas, no abra la unidad.En caso de avería, solicite los servicios de personal cualificado solamente.

El cable de alimentación de CA solamente deberá ser cambiado en un taller de reparaciones cualificado.

Notas sobre la utilización
Sobre el enchufe del cable de alimentación de

CA

Existen dos modelos de AC-V700, que se diferencian por la forma del enchufe del cable de alimentación de CA.

ModeloForma del enchufe
Modelo para EE.UU./CanadáPolarizado
Modelo para otros paísesNo polarizado

Modelo para EE.UU. y Canadá: Por motivos de seguridad, una cuchilla del enchufe es más ancha que la otra, y solamente encajará en el tomacorriente de una sola forma. Si no puede insertar firmemente el enchufe en el tomacorriente, póngase en contacto con su proveedor.

Sobre el tiempo restante de la batería

Durante la carga de la batería, esta unidad mostrará el tiempo restante de la batería con su equipo de vídeo, etc. en las condiciones siguientes.

Utilización de una batería “InfoLITHIUM”Utilización de un equipo de vídeo que posea la marca

Cerciórese de utilizar una batería que posea la marca . Si su equipo de vídeo puede utilizar baterías “InfoLITHIUM”, consulte el manual de instrucciones del mismo.

Aunque los modelos siguientes son compatibles con “InfoLITHIUM”, en esta unidad no se visualizará el tiempo restante de la batería.

DCR- PC7/PC7E/PC10/PC10E/SC100/SC100E/TRV7/TRV7E

CCD- TR555/TR555E/TR610E/TR710/TR710E/TR760E/TR790E/TR810E/ TR820E/TR825E/TR910/TR910E/TR920E/TR930/TR1100E/ TR2200E/TR2300/TR2300E/TR3100E/TR3300/TR3300E/TR3400/ TRV31/TRV31E/TRV41/TRV41E/TRV51/TRV51E/TRV54E/ TRV56E/TRV61E/TRV62/TRV64E/TRV72/TRV81/TRV81E/ TRV82/TRV91E/TRV94/TRV94E/TRV101/TRV101E/ SC55/SC55E/SC65/SC65E

GV-A500/A500E

Si utiliza un equipo de vídeo que posea la marca , la visualización del tiempo restante de la batería que esté cargando

corresponderá a un equipo de vídeo que posee la marca a la que haya fijado por última vez la batería.

Carga

Utilice solamente una batería de tipo de iones de litio. Esta unidad no podrá utilizarse para cargar una batería de tipo níquel-cadmio/níquel- hidrógeno.

Fije firmemente la batería.Cargue la batería sobre una superficie plana exenta de vibraciones.Temperatura de carga

La gama de temperaturas para carga es de 0 a 40°C. Sin embargo, para obtener la máxima eficacia de la batería, la gama de temperaturas recomendada para la carga es de 10 a 30°C.ded temperature range when charging is 10°C to 30°C (50°F to 86°F).

Otros

La placa de características en la que se indica la tensión de alimentación, el consumo, etc., se encuentra en la parte inferior.

Mientras el adaptador de CA/cargador esté enchufado en un tomacorriente, a través del mismo circulará cierta cantidad de corriente.

Cuando no vaya a utilizar la unidad durante mucho tiempo, desenchúfela del tomacorriente. Para desconectar el cable de alimentación, tire del enchufe. No tire nunca del propio cable.

No utilice la unidad con un cable dañado, cuando se haya caído, ni cuando esté dañada.

Cerciórese de que ningún objeto metálico entre en contacto con las partes metálicas de la unidad ni de la placa conectora. En caso contrario podría producirse un cortocircuito y la unidad se dañaría.

Mantenga siempre limpios los contactos metálicos.No desarme ni modifique la unidad.No golpee ni deje caer la unidad.Cuando utilice la unidad, se calentará. Sin embargo, esto es normal.

Mantenga la unidad alejada de receptores de AM, porque podría perturbarse la recepción de AM.

No coloque la unidad en un lugar:Extremadamente cálido o fríoPolvoriento o sucioMuy húmedoSometido a vibraciones

Si tiene alguna dificultad, desenchufe la unidad y póngase en contacto con su proveedor Sony.

Especificaciones
Alimentación100 - 240 V CA, 50/60 Hz
Consumo

25 W

 

Modo de carga:

 

35 VA (100 V CA), 46 VA (240 V CA)

 

Modo de operación:

 

39 VA (100 V CA), 50 VA (240 V CA)
Tensión de salida

DC OUT:

 

8,4 V, 2,0 A en el modo de operación

 

Terminales de carga de la batería:

 

8,4 V, 1,4 A en el modo de carga
AplicaciónBatería NP-F100/F200/F300/F330/F530/

 

CF540/F550/F730/F750/F930/F950 Sony
Temperatura de funcionamiento

 

0 a 40°C

Temperatura de almacenamiento

 

–20 a 60°C

DimensionesAprox. 127 ⋅ 55 ⋅ 95 mm (an/al/prf)
MasaAprox. 225 g
Accesorios suministradosCable conector DK-415 (1),

 

Cable de alimentación de CA (1)
El diseño y las especificaciones están sujetos a cambio sin previo aviso.

Dependiendo del diseño del tomacorriente, si es necesario, utilice un adaptador de enchufe de CA adquirido en un establecimiento del ramo.

Tomacorriente

AC-V700

Adaptador de enchufe de CA

Esta marca indica que este producto es genuino y está relacionado con productos de vídeo Sony. Cuando adquiera productos de vídeo Sony, Sony recomienda solicitar accesorios con la marca “GENUINE VIDEO ACCESSORIES” (accesorios de vídeo genuinos).

Identificación de partes
Consulte la ilustración A.1Obturador de terminales2 Polaridad de carga3 Palanca de liberación de la batería4 Conector de salida de CC (DC OUT)5 Guía6 Lámpara indicadora de carga (CHARGE)7 Selector de modo8 Tecla de cambio de visualización (DISPLAY CHANGE) 9 VisualizadorVisualizador0Indicador de “InfoLITHIUM”

Se encenderá cuando instale la batería “InfoLITHIUM”. !¡ Indicador de advertencia (WARNING)

!™ Indicador de tiempo de carga (TIME TO CHG) Indicador de tiempo

Indicador de tiempo restante de batería (BATTERY LIFE) !∞ Indicador de videograbadora/videocámara (VCR/CAMERA) Indicador de carga completa

Indicador de batería restante
Para cargar la batería
Consulte la ilustración B.1Ponga el selector de modo en CHARGE.2Conecte el cable de alimentación a esta unidad.3Conecte el cable de alimentación a un tomacorriente.Sonará un pitido y se encenderá el visualizador.4Instale la batería.Se iniciará la carga. Cuando el indicador de batería restante pase a ser

, y se encienda la lámpara CHARGE, habrá finalizado la carga normal. Para realizar la carga completa, que le permitirá utilizar la batería algo más que con la “carga normal”, deje la batería instalada en la unidad hasta que se apague la lámpara CHARGE.

Extraiga la batería cuando lo requiera. Podrá utilizarse incluso aunque no se haya completado la carga.

Indicador de batería restante
Carga normalCarga completa

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Para instalar la bateríaNP-F550, etc. (Ilust. B-1)1Sitúe la batería sobre a.

Alinee el extremo de la batería que contiene la marca 4 con el borde del obturador de terminales de esta unidad.

a se pliega al situar la batería sobre dicho punto.2Deslice la batería en el sentido de la flecha.Presione la batería hasta cubrir el obturador de terminales por completo.NP-F100, etc. (ilust. B-2)1Deslice la batería a lo largo de guía hasta a.2Presione la batería hacia abajo hasta que se oiga un clic.Nota

No golpee la polaridad de carga. Asimismo, asegúrese de no golpear la batería al instalarla.

Tiempo de carga

En la tabla siguiente se muestra el tiempo de carga para una batería completamente descargada.

BateríaTempo de carga

Batería

Tempo de carga

 

 

 

 

 

NP-CF540

110 (50)

 

NP-F100

100 (40)

 

 

 

 

 

NP-F550

115 (55)

 

NP-F200

115 (55)

 

 

 

 

 

NP-F750

170 (110)

 

NP-F300

160 (100)

 

 

 

 

 

NP-F950

225 (165)

 

 

 

 

 

 

 

 

Minutos aproximados para cargar completamente una batería vacía (carga completa).

Los minutos aproximados entre paréntesis indican el tiempo cuando la cargue normalmente (carga normal).

Para asegurar la duración útil de la batería, consulte el manual de instrucciones del equipo de vídeo utilizado.

El tiempo de carga puede diferir dependiendo de la condición de la batería o de la temperatura ambiental.

NotasSi pone el selector de modo en VCR/CAMERA durante la carga, ésta se parará.

Cuando instale una batería completamente cargada, la lámpara CHARGE parpadeará una vez y después se apagará.

Si la lámpara CHARGE no se enciende o parpadea, compruebe si la batería está correctamente instalada en el adaptador de CA/cargador. Si no está bien instalada, no se cargará.

Cuando parpadee la lámpara CHARGE

Si ocurre algún problema durante la carga, la lámpara CHARGE parpadeará y en el visualizador aparecerá WARNING. Compruebe el organigrama siguiente.

Retire la bater a de esta unidad y, a continuaci n, vuelva a instalar la misma bater a.

Si la l mpara CHARGE

 

Si la l mpara CHARGE se ilumina y
vuelve a parpadear:

 

no vuelve a parpadear:
Instale otra bater a.

 

Si la l mpara CHARGE se apaga

 

 

 

porque ha transcurrido el tiempo

 

 

 

 

 

de carga, no hay problema.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Si la l mpara CHARGE

 

Si la l mpara CHARGE se ilumina y

vuelve a parpadear:

 

no vuelve a parpadear:

El problema reside en esta

 

Si la l mpara CHARGE se apaga

unidad.

 

porque ha transcurrido el tiempo de

 

 

 

carga, el problema reside en la bater a

 

 

 

 

 

instalada en primer lugar.

 

 

 

 

 

 

 

 

 

 

P ngase en contacto con su proveedor Sony m s cercano en relaci n con el producto afectado.

Para extraer la batería

NP-F550, etc. (Ilust. B-1)

Desilce la batería en el sentido de la flecha y, a continuación, levántela para extraerla.

NP-F100, etc. (Ilust. B-2)Retire la batería mientras desliza la palanca de liberación de la batería.Para comprobar la carga

Cuando cargue, podrá comprobar el tiempo de carga en el visualizador. Un minuto después de haber iniciado la carga, en el visualizador aparecerá

BATTERY LIFE.Durante la carga, presione DISPLAY CHANGE.

Cada vez que presione DISPLAY CHANGE, la visualización cambiará de la forma siguiente.

 

 

 

 

 

 

 

 

Tiempo restante de la batería

 

BATTERY LIFE

cuando ésta esté instalada en su

 

 

 

 

 

 

m

 

equipo de vídeo para baterías

 

 

 

 

 

 

 

 

“InfoLITHIUM”

 

 

 

 

 

 

 

 

 

 

DISPLAY

 

 

El tiempo no se visualizará cuando el

 

 

 

 

tiempo restante de la batería sea

 

 

CHANGE

 

 

 

 

 

 

 

 

 

 

inferior a 5 minutos.

 

 

 

 

 

 

 

 

Tiempo restante hasta que

 

 

 

 

 

 

 

 

TIME TO CHG

 

 

 

 

 

 

 

finalice la carga normal

 

 

 

 

 

m

 

• El tiempo de carga normal no se

NORMAL

 

 

 

 

 

 

visualizará después de haber

 

 

 

 

 

 

 

 

 

 

DISPLAY

 

 

finalizado la carga normal.

 

 

CHANGE

 

 

 

 

 

 

 

 

 

 

 

Tiempo restante hasta que

 

 

 

 

 

 

 

 

TIME TO CHG

 

 

 

 

 

 

 

finalice la carga completa

 

 

 

 

 

 

 

 

• El tiempo de carga normal no se

FULL

 

h

 

 

 

m

 

visualizará después de haber

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DISPLAY

 

 

finalizado la carga completa.

 

 

CHANGE

 

 

 

Notas

La visualización del tiempo mostrará el tiempo aproximado cuando la carga se realice a 10 - 30ºC. La visualización del tiempo puede diferir del tiempo de carga real dependiendo de las condiciones y circunstancias de utilización.

La visualización de tiempo puede mostrar “– – – –” en los casos siguientes. Sin embargo, esto no significa que la unidad está funcionando mal.

El tiempo de batería restante es inferior a 5 minutos.

Existe una diferencia entre el tiempo visualizado y el tiempo de carga real. Aunque suceda esto, continúe cargando.

La carga completa requerirá aproximadamente 1 hora después de haber finalizado la carga normal. Si extrae la batería entre la carga normal y la carga completa, es posible que el tiempo de carga no se visualice adecuadamente en la próxima carga.

Si el tiempo de carga no se visualiza adecuadamente, cargue completamente la batería. El tiempo de carga se visualizará apropiadamente.

Cuando instale una batería completamente cargada en esta unidad, en el visualizador puede aparecer “TIME TO CHG FULL 1h”. Sin embargo, esto no significa que la unidad está funcionando mal.

Dependiendo de las condiciones y circunstancias de utilización, es posible que no se visualice BATTERY LIFE.

Es posible que tenga que esperar cierto tiempo hasta que el visualizador muestre la indicación de tiempo después de haber presionado DISPLAY CHANGE.

Para utilizar el equipo de vídeo
Consulte la ilustración C.

Para la videocámara DCR-TRV9, etc., utilice el cable conector DK-415 suministrado. Para la videocámara DCR-PC10, etc., utilice un cable conector DK-626 (no suministrado).

Con respecto a los detalles sobre la conexión, consulte el manual de instrucciones del equipo de vídeo.

1Ponga el selector de modo en VCR/CAMERA.2Conecte el cable de alimentación en un tomacorriente.3Conecte el cable conector b al conector DC OUT de esta unidad.4Conecte el cable conector al equipo de vídeo.DCR-TRV9, etc. (Ilust. C-1)

Manteniendo presionada la placa conectora c, deslícela hacia abajo. Para extraer la placa conectora, deslícela hacia arriba manteniendo presionada la palanca de liberación de la batería d.

DCR-PC10, etc. (Ilust. C-2)Abra la cubierta e inserte la clavija conectora e.

Para desconectar la clavija conectora, tire de ella manteniendo presionada la tecla f.

Notas

Si pone el selector de modo en CHARGE mientras esté utilizando el equipo de vídeo, la fuente de alimentación de ésta se cortará.

Usted no podrá cargar la batería instalada en esta unidad mientras esté alimentando el equipo de vídeo.

Si las imágenes se ven con perturbaciones, mantenga esta unidad alejada del equipo de vídeo.