AC/DC Adaptor/Charger
Operating Instructions
Mode d’emploi
Manual de instrucciones
使用说明书TM
SERIES
TM
SERIES
AC-VQ850D
Sony Corporation © 2001 Printed in JapanOwner’s RecordThe model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. AC- |
| Serial No. |
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to the presence of uninsulated “Dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTIONYou are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
NOTICE FOR THE CUSTOMERS IN THE U.S.A AND CANADAThe Graphical Symbols with Supplemental Marking is located on the bottom of the unit.
Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.–Increase the separation between the equipment and receiver.–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOMA moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the supplied one and approved by ASTA or BSI to BS 1362 (i.e., marked with or mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Printed on 100% recycled paper using VOC (Volatile Organic
A
1 |
| |
2 | 5 | |
| ||
| 6 | |
3 |
| |
4 | 7 | |
8 | ||
|
9 |
|
|
| qd |
|
|
|
| qf |
0 | WARNING |
| VCR/CAMERA |
|
BATTERY LIFE | qg | |||
qa | TIME TO CHG |
|
|
|
NORMAL FULL | h | m |
| |
|
|
B
| 2 |
3 | 3 |
| |
2 | 4 |
| 1 |
1
To removePour retirer
2 | To remove |
| Pour retirer |
C
| 2 |
3 | 3 |
| |
| 2 |
| 1 |
| 4 A 4 A |
1
BC
2
D
Before operating the unit, please read this manual thoroughly and retain it for future reference.
TheConnect the power cord (supplied) to a wall outlet, or connect the car battery cord
•To charge a lithium ion type battery pack.
•To enable the power supply to the video equipment, connection cords are included with this unit.
What is the “InfoLITHIUM” ?The “InfoLITHIUM” is a lithium ion battery pack which can exchange data with compatible electronic equipment about its battery consumption. Sony recommends that you use the “InfoLITHIUM” battery pack with electronic
equipment having the mark.“InfoLITHIUM” is a trademark of Sony Corporation.WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.To avoid electrical shock, do not open the cabinet.Refer servicing to qualified personnel only.AC power cord must be changed only at the qualified service shop.For the customers in CanadaCAUTIONTO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.Notes on Use
About the AC power cord plugThe
Model | Shape of the plug |
Model for USA/Canada | Polarized |
Model for other countries/regions | Non polarized |
•The model for USA and Canada: One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
About the remaining battery timeWhile charging the battery pack, this unit will show the remaining battery time with your video equipment, etc. on the following conditions.
•Using the “InfoLITHIUM” battery pack•Using the electronic equipment having the markMake sure that you use the battery pack having the mark. Consult the operating instructions supplied with your video equipment if it is applied to “InfoLITHIUM”.
Though the following models are applied to “InfoLITHIUM”, the remaining battery time is not displayed on this unit.
DCR- SC100/SC100E/TRV7/TRV7ECCD- TR555/TR555E/TR610E/TR710/TR710E/TR760E/TR790E/TR810E/ TR820E/TR825E/TR910/TR910E/TR920E/TR930/TR1100E/ TR2200E/TR2300/TR2300E/TR3100E/TR3300/TR3300E/TR3400/ TRV31/TRV31E/TRV41/TRV41E/TRV51/TRV51E/TRV54E/ TRV56E/TRV61E/TRV62/TRV64E/TRV72/TRV81/TRV81E/ TRV82/TRV91E/TRV94/TRV94E/TRV101/TRV101E/ SC55/SC55E/SC65/SC65E
If you use this battery pack with electronic equipment not having the mark, the remaining battery capacity will not be indicated in minutes.*
*The indication may not be accurate depending on the condition and environment which the equipment is used under
Warranty for Recorded ContentContents of the recording cannot be compensated if recording or playback is not made due to a malfunction of the battery pack, AC power adaptor, AC power adaptor/charger, etc.
ChargingUse only a lithium ion type battery pack. This unit cannot be used to charge a
The temperature range for charging is 0 °C to 40 °C (32 °F to 104 °F). However, to provide maximum battery efficiency, the recommended temperature range when charging is 10 °C to 30 °C (50 °F to 86 °F).
Others•The negligible amount of electric current will flow into the AC adaptor/ charger as long as the AC adaptor/charger is plugged into the wall outlet.
•Unplug the unit from the wall outlet if it will not be used for extended period of time. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•Do not operate the unit with a damaged cord or if it has been dropped or damaged.
•Use this unit near to a wall outlet. This is to ensure that the power plug can be immediately unplugged from the wall outlet to turn the power off if some abnormality occurs during use.
•Use this car battery charger only for cars which use a 12 or 24 volt battery.•There are cars which are negatively grounded and there are others which are positively grounded.
This unit is for negatively grounded cars only.•Use the unit with leaving the car engine going. If you use the unit with the car engine stopped, the car battery may become unusable.
•Unplug the car battery cord from the cigarette lighter socket when not in use. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•The nameplate indicating operating voltage, power consumption, etc. is located on the bottom.
•Be sure that nothing metallic comes into contact with the metal parts of the unit or connecting plate. If it does, a short may occur and the unit may be damaged.
•Always keep the metal contacts clean.•Do not disassemble or convert the unit.•Do not apply mechanical shock or drop the unit.•While the unit is in use, it gets warm. But this is normal.•Keep the unit away from AM receivers, because it will disturb AM reception.•Do not place the unit in a location where it is:—Extremely hot or cold—Dusty or dirty—Very humid—Vibrating•Placing this unit in locations subject to the direct sunlight such as on dashboards or near heating apparatus may cause this unit to deform or malfunction.
If any difficulty should arise, unplug the unit and contact your nearest Sony dealer.
Troubleshooting
Symptom | Cause/Solution |
Video equipmet does not | •The power plug is disconnected from the |
work. | wall outlet. |
| •The car battery cord |
| disconnected from the cigarette lighter socket. |
| t Insert into the wall outlet or cigarette |
| lighter socket. |
| •The connector cable is not properly connected. |
| t Connect properly. |
| •The mode change switch is set to CHARGE. |
| t Set the mode change switch to VCR/ |
| CAMERA. |
The battery is not charged. •The mode change switch is set to VCR/ | |
| CAMERA. |
| t Set the mode change switch to CHARGE. |
|
|
Power immediately turns | •Fully charge again. |
off even though there is | t The remaining battery power will be |
sufficient remaining battery | correctly displayed. |
power. |
|
(Read “About the | t The normal charge time is not displayed |
remaining time.”) | after the normal charge is completed. |
| •The full charge time is not displayed. |
| t The full charge time is not displayed after |
| the full charge is completed. |
The CHARGE lamp blinks, | •If the battery pack is charged in hot locations |
and “CHARGE ERROR” is | such as in the direct sunlight, the device |
displayed in the display | protection function operates to stop charging. |
window. | t Return this unit to the recommended |
| temperature (10 °C to 30 °C), remove the |
| battery and then |
Remove the battery pack from this unit, then install the same battery pack again.
If the CHARGE lamp flashes |
| If the CHARGE lamp lights and | ||
again: |
| does not flash again: | ||
Install another battery pack. |
| If the CHARGE lamp goes out | ||
|
|
| because the charging time has | |
|
| |||
|
|
| passed, there is no problem. | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If the CHARGE lamp flashes |
| If the CHARGE lamp lights and | ||
again: |
| does not flash again: | ||
The problem is with this unit. |
| If the CHARGE lamp goes out | ||
|
|
| because the charging time has | |
|
|
| passed, the problem is with the | |
|
|
| battery pack first installed. | |
|
|
|
|
|
|
|
|
|
|
Please contact your nearest Sony dealer in connection with the product with the problem.
Specifications
Power requirements | 100 - 240 V AC, 50/60 Hz |
| 12/24 V DC |
| (only for negative grounded cars) |
Power consumption | 25 W |
| Charge mode: |
| 35 VA (100 V AC), 50 VA (240 V AC) |
| Operating mode: |
| 40 VA (100 V AC), 50 VA (240 V AC) |
Output voltage | DC OUT: |
| 8.4 V, 2.0 A in operating mode |
| Battery charge terminal: |
| 8.4 V, 1.4 A in charge mode |
Application | Sony battery pack |
| FM90/FM91/F330/F530/F550/F730/F730H/ |
| F750/F930/F950/F960 |
Operating temperature | 0 °C to 40 °C (32 °F to 104 °F) |
Storage temperature | |
Dimensions | Approx. 136 ⋅ 48 ⋅ 90 mm (w/h/d) |
(Projections are not included | (5 1/3 ⋅ 1 10/16 ⋅ 3 1/2 inches) |
in the dimensions.) |
|
Mass | Approx. 280 g (9.9 oz) |
Supplied accessories | Connecting cord |
AC power cord (1) | |
| |
Input voltage | DC 12/24V |
Fuse rating | 125 V 4 A |
Cord length | Approx. 1.5 m |
Mass | Approx. 80 g |
Use a commercially available AC plug adaptor, if necessary, depending on the design of the wall outlet.
Wall outletIdentifying the parts
See illustration A.1Terminal shutter (“InfoLITHIUM” (M series))2 Terminal shutter (“InfoLITHIUM” (L series))3 DC IN connector (only forTo Charge the Battery Pack
See illustration B.When the power cord and car battery cord
Charging begins. When the remaining battery indicator becomes and the CHARGE lamp lights up, normal charge is completed. For full charge, which allows you to use the battery slightly longer than “normal charge”, leave the battery pack attached until the CHARGE lamp goes out.
Remove the battery pack when required. It can be used even if the charging is not completed.
Remaining battery indicatorNormal charge | Full charge | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tht set is not disconnected from the AC power source (wall outlet) as long as it is connected to the wall outlet, even if the set itself has been turned off.
1Place the battery pack on this unit with the b mark facing the terminal shutter (L series).
2Slide the battery pack in the direction of the arrow.Press the battery pack until the terminal shutter enters completely into this unit.
“InfoLITHIUM” (M series)1Place the battery pack on this unit with the B mark facing the terminal shutter (M series).
2Slide the battery pack in the direction of the arrow.
Press the battery pack until the terminal shutter lifts completely.To remove the battery packSlide the battery pack in the direction of the arrow, then lift it straight out.
Slide the battery pack in the direction of the arrow, then lift it straight out.
NoteWhen you install the battery pack, be sure not to strike it to the terminal of the AC adaptor/charger.
Charging timeThe following table shows the charging time for the main battery pack which is discharged completely.
Battery pack | Charging time | Battery pack | Charging time | |
(“InfoLITHIUM” (L series)) |
|
| ( “InfoLITHIUM” (M series)) | |
|
|
|
|
|
115 (55) |
| 105 (45) | ||
|
|
|
|
|
170 (110) |
| 150 (90) | ||
|
|
|
|
|
245 (185) |
| 205 (145) | ||
|
|
|
|
|
•Approximate minutes in parentheses indicate the time when you charge normally (Normal charge).
•To ascertain the battery life, refer to the instruction manual of the video equipment which you use.
•The charging time may differ depending on the condition of the battery pack or the temperature of the environment.
Notes•When the mode change switch is set to VCR/CAMERA during charging, charging stops.
•If the CHARGE lamp does not light or flash, check that the battery pack is correctly attached to the AC adaptor/charger. If it is not attached it will not be charged.
To Check ChargingWhile charging, you can check the charging time on the display. After starting charging in a minute, BATTERY LIFE lights up on the display. The displayed remaining time is the approximate time when taking photographs via the viewfinder. The remaining time is shorter when the LCD display is used.
Press DISPLAY CHANGE while charging.Each time you press DISPLAY CHANGE, the display changes as follows.The remaining battery time when the battery pack being charged is attached to your “InfoLITHIUM” electronic equipment
The time is not displayed when the remaining battery time is less than 5 minutes.
The remaining time until normal charge is completedThe normal charge time is not displayed after the normal charge is completed.
The remaining time until full charge is completedThe full charge time is not displayed after the full charge is completed.
Notes
•The time display shows the approximate time when charging at 10 °C - 30 °C. The time display may differ from the actual charging time depending on using conditions and circumstances.
•The time display may show “– – –
–There is a difference between the displayed time and actual charging time. Even if this happens, continue charging.
•Full charge requires about 1 hour after normal charge is completed. If you remove the battery pack between normal charge and full charge, the charging time may not be displayed properly in the next charging.
•When a battery that has not been used for a long time is charged, the displayed remaining time and full charge time sometimes differ from the actual times. This is not a malfunction. If this happens, charge the battery pack until it is fully charged. The correct times can be displayed.
•When you attach a fully charged battery pack to this unit, “TIME TO CHG FULL 1h” may appear on the display. However, this is not a malfunction.
•You may wait for a while after pressing DISPLAY CHANGE until the display shows the time indication.
•To display the remaining battery time of a new battery, attach it to your video camera recorder and use it for about 20 seconds. Then, charge the battery with this unit.
To Operate Video Equipment
See illustration C.For details of the connection, refer to the instruction manual of the video equipment.
1Set the mode change switch to VCR/CAMERA.2Connect the power cord or the car battery cord to this unit.
3Connect the power cord to a wall outlet or a cigarette lighter socket.
4Connect the connecting cord A to the DC OUT connector of this unit.5Connect the connecting cord to the video equipment.When using the connecting cordTo remove the connecting plate, slide it up while pressing the battery release lever C.
When using the connecting cordOpen the cover, and insert the connecting plug D. To remove the connecting plug, pull it out.
Notes
•If you set the mode change switch to CHARGE while operating the video equipment, the power supply to the video equipment stops.
•You cannot charge the battery pack attached to this unit while supplying the power to the video equipment.
•Keep this unit away from the video equipment if the picture is disturbed.Fuse Replacement
If this unit is not working properly while using
Notes
•Replace the fuse with a fuse of the same voltage (4 A, 125 V).•If the car's cigarette lighter socket is dirty with ash, etc., the plug part will become hot due to a poor connection. Be sure to clean it before using.
•When replacing the fuse, do not substitute anything for the specified fuse.•If the fuse blows again soon after replacement, consult your nearest Sony dealer.
Please contact your car dealer about the polarity that your car is grounded or the voltage of your car battery, etc.
Nous vous remercions pour l’achat de cet adaptateur secteur CA/CC/ chargeur Sony.
Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour toute référence future.
L’adaptateur secteur/chargeurRaccordez le cordon d’alimentation (fourni) à une prise secteur, ou le cordon
•Pour charger une batterie au
•Pour alimenter un appareil vidéo, avec les cordons de liaison fournis avec cet appareil.
Que signifie “InfoLITHIUM”?La batterie “InfoLITHIUM” est une batterie au
.
“InfoLITHIUM”est une marque de commerce de Sony Corporation.AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un technicien qualifié.
Le cordon d’alimentation secteur de l’appareil doit être changé par un professionnel uniquement.
Pour les utilisateurs au CanadaATTENTIONPOUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU FOND.
Remarques sur l’utilisation
Fiche du cordon d’alimentation secteurLe modèle
Modèle | Forme de la fiche |
Modèle pour les | Polarisée |
et le Canada |
|
Modèle pour les autres pays | Non polarisée |
ou régions |
|
|
|
•Modèle pour les
Pendant la recharge de la batterie, cet appareil indiquera l’autonomie de l’appareil vidéo, etc. dans les cas suivants:
•Vous utilisez une batterie “InfoLITHIUM”•Vous utilisez un appareil électronique utilisant le logo
.
Consultez le mode d’emploi fourni avec votre appareil vidéo s’il s’agit d’un appareil “InfoLITHIUM”.
Bien que les modèles suivants soient de type “InfoLITHIUM”, l’autonomie ne peut pas être indiquée par cet appareil.
DCR- SC100/SC100E/TRV7/TRV7E
CCD- TR555/TR555E/TR610E/TR710/TR710E/TR760E/TR790E/TR810E/ TR820E/TR825E/TR910/TR910E/TR920E/TR930/TR1100E/ TR2200E/TR2300/TR2300E/TR3100E/TR3300/TR3300E/TR3400/ TRV31/TRV31E/TRV41/TRV41E/TRV51/TRV51E/TRV54E/ TRV56E/TRV61E/TRV62/TRV64E/TRV72/TRV81/TRV81E/ TRV82/TRV91E/TRV94/TRV94E/TRV101/TRV101E/ SC55/SC55E/SC65/SC65E
Si vous utilisez la batterie “InfoLITHIUM” avec des appareils électroniques ne portant
pas le logo , l’autonomie de la batterie ne sera pas indiquée en minutes.*
*Il se peut que l’indication ne soit pas précise. Cela dépend de la situation et de l’environnement dans lesquels l’appareil est utilisé
Garantie concernant l’enregistrementAucune compensation ne peut être accordée si l’enregistrement ou la lecture n’a pas pu être effectué en raison d’un problème de batterie, d’adaptateur secteur ou d’adaptateur secteur/chargeur, etc.
RechargeN’utilisez que des batteries au
La batterie peut être rechargée à une température comprise entre 0 °C et 40 °C (32 °F et 104 °F). Cependant, pour que son efficacité soit optimale, il est conseillé de la recharger entre 10 °C et 30 °C (50 °F et 86 °F).
Divers•Une quantité négligeable d’électricité circule dans l’appareil s’il reste branché sur la prise murale.
•Débranchez l’appareil de la prise murale si vous n’avez pas l’intention de l’utiliser pendant un certain temps. Pour débrancher le cordon secteur, tirez sur la fiche. Ne tirez jamais sur le cordon.
•N’utilisez pas l’appareil lorsque le cordon est endommagé, ou si l’adaptateur est tombé ou a été endommagé.
•Utilisez cet appareil près d’une prise murale. Vous pourrez débrancher immédiatement la fiche de la prise murale pour éteindre l’appareil en cas d’anomalie.
•N’utilisez ce chargeur que dans des voitures avec batterie de 12 ou 24 volts.•Il existe des voiture à masse négative et d’autres à masse positive.Cet appareil ne doit être utilisé que dans les voitures à masse négative.•Lorsque vous utilisez cet appareil, laissez tourner le moteur de la voiture, sinon la batterie se videra.
•Débranchez le cordon
•La plaque signalétique indiquant la tension de fonctionnement, la consommation électrique et d’autres informations électriques se trouve sous l’appareil.
•Evitez que des objets métalliques ne touchent les parties métalliques de l’appareil ou de la plaque de connexion. Un
•Ne pas laisser l’appareil près d’un récepteur AM, car il perturbera la réception AM.
•Ne pas entreposer l’appareil dans les endroits suivants:—extrêmement chauds ou froids—poussiéreux ou sales—très humides—exposés à des vibrations.•N’exposez pas cet appareil à la lumière directe du soleil, comme sur le tableau de bord d’une voiture, ni à la chaleur d’un appareil de chauffage, car il pourrait être déformé ou ne plus fonctionner.
En cas de problème, débranchez l’appareil et contactez votre revendeur Sony.En cas de panne
Symptômes | Causes/Solutions |
L’appareil vidéo ne | •Le cordon d’alimentation est débranché de la |
fonctionne pas. | prise secteur. |
| •Le cordon |
| débranché de la prise |
| t |
| douille |
| •Le cordon de liaison n’est pas raccordé |
| correctement. |
| t |
| •Le sélecteur de mode est réglé sur CHARGE. |
| t |
|
|
La batterie n’est pas | •Le sélecteur de mode n’est pas réglé sur |
chargée. | VCR/CAMERA. |
| t |
|
|
L’alimentation est tout de | •Rechargez une nouvelle fois la batterie |
suite coupée, bien que | complètement. |
l’autonomie de la batterie | t L’autonomie n’est pas indiquée |
soit suffisante. | correctement. |
(Voir “Iindication | indiqué. |
d’autonomie”) | t Le temps d’une recharge normale n’est |
| pas indiqué lorsque la recharge normale |
| est terminée. |
| •Le temps d’une recharge complète n’est pas |
| indiqué. |
| tLe temps d’une recharge complète n’est |
| pas indiqué lorsque la recharge complète |
| est terminée. |
Le voyant CHARGE | •Si la batterie est rechargée dans un lieu |
clignote, et “CHARGE | chaud, par exemple en plein soleil, le |
ERROR” apparaît. | dispositif de protection s’enclenche et la |
| recharge s’arrête. |
| t Exposez l’appareil à la température |
| recommandée (10 °C à 30 °C), enlevez la |
| batterie et |
|
|
Si le témoin CHARGE |
| Si le témoin CHARGE s’allume mais | ||
clignote encore: |
| ne clignote pas de nouveau: | ||
Installez une autre batterie |
| Si le témoin CHARGE s’éteint parce | ||
rechargeable. |
| que la recharge est terminée, il n’y a | ||
|
|
| aucun problème. | |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Si le témoin CHARGE |
| Si le témoin CHARGE s’allume mais | ||
clignote de nouveau: |
| ne clignote pas de nouveau: | ||
Le problème vient de |
| Si le témoin CHARGE s’éteint parce | ||
l’appareil. |
| que la recharge est terminée, le | ||
|
|
| problème vient de la première | |
|
|
| batterie rechargeable installée. | |
|
|
|
|
|
Veuillez contacter votre revendeur Sony et lui apporter l’appareil qui ne fonctionne pas.
Spécifications
Alimentation | Secteur 100 - 240 V, 50/60 Hz |
| 12/24 V CC (voitures à masse négative) |
Consommation | 25 W |
| Mode de charge: |
| 35 VA (100 V secteur), 50 VA (240 V secteur) |
| Mode de fonctionnement: |
| 40 VA (100 V secteur), 50 VA (240 V secteur) |
Tension de sortie | DC OUT: |
| 8,4 V, 2,0 A en mode de fonctionnement |
| Borne de recharge de la batterie: |
| 8,4 V, 1,4 A en mode de charge. |
Application | Batterie rechargeable Sony |
| FM70/FM90/FM91/F330/F530/F550/F730/ |
| F730H/F750/F930/F950/F960 |
Température de fonctionnement | |
| 0 °C à 40 °C (32 °F à 104 °F) |
Température d’entreposage | |
Dimensions hors tout | Env. 136 ⋅ 48 ⋅ 90 mm (l/h/p) |
Poids | (5 1/3 ⋅ 1 10/16 ⋅ 3 1/2 pouces) |
Env. 280 g (9,9 on.) | |
Accessoires fournis | Cordon de liaison |
| Cordon d’alimentation secteur (1) |
| |
Tension d’entrée | CC 12/24 volts |
Capacité du fusible | 125 V 4 A |
Longueur du cordon | Approx. 1,5 m |
Poids | Approx. 80 g |
Si la fiche ne rentre pas dans la prise, utilisez une adaptateur de fiche (en vente dans le commerce).
Prise muraleNomenclature
Voir l’illustration A.1Obturateur de borne (“InfoLITHIUM” (modèles M))2 Obturateur de borne (“InfoLITHIUM” (modèles L))3 Prise DC INPour charger une batterie
Voir l’illustration B.Lorsque le cordon d’alimentation et le cordon
3Branchez le cordon d’alimentation sur une prise secteur ou sur une douille
est plein et le témoin CHARGE s’allume, la recharge normale est terminée. Pour une recharge complète qui vous permettra d’utiliser plus longtemps l’appareil vidéo, laissez la batterie en place jusqu’à ce que le témoin CHARGE s’éteigne.
Enlevez la batterie quand nécessaire. Elle peut être utilisée même si elle n’est pas complètement rechargée.
Indicateur de charge de la batterieCharge normale | Charge complète | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PRECAUTION
L’ensemble
1Placez la batterie sur cet appareil avec le repère b orienté vers l‘obturateur de borne (modèle L).
2Faites glisser la batterie dans le sens de la flèche.Appuyez sur la batterie jusqu‘à ce que l‘obturateur de borne soit complètement introduit dans cet appareil.
“InfoLITHIUM” (Modèle M)1Placez la batterie sur cet appareil avec le repère B orienté vers l‘obturateur de borne (modèle M).
2Faites glisser la batterie dans le sens de la flèche.
Appuyez sur la batterie jusqu‘à ce que l‘obturateur de borne se soit complètement relevé.
Pour enlever la batterie rechargeableFaites glisser la batterie dans le sens de la flèche, puis
Lorsque vous installez la batterie, veillez à ne pas heurter la borne de l‘adaptateur secteur/chargeur.
Temps de rechargeLe tableau suivant indique le temps de recharge quand la batterie principale est complètement déchargée.
Batterie | Temps de |
| Batterie | Temps de |
| |
rechargeable | recharge |
| rechargeable | recharge |
| |
(“InfoLITHIUM” (Modèle L)) |
|
| (“InfoLITHIUM” (Modèle M)) |
|
|
|
|
|
|
|
|
|
|
115 (55) |
| 105 (45) |
|
| ||
|
|
|
|
|
|
|
170 (110) |
| 150 (90) |
|
| ||
|
|
|
|
|
|
|
245 (185) |
| 205 (145) |
|
| ||
|
|
|
|
|
|
|
•Temps de recharge approximatif en minutes pour recharger complètement une batterie vide (Recharge complète).
•Le temps entre parenthèses indiquent approximativement le nombre de minutes pour une recharge normole (Recharge normale).
•Voir le mode d’emploi de l’appareil vidéo utilisé pour l’autonomie de la batterie.
•Le temps de recharge varie selon l’état de la batterie et la température ambiante.
Remarques•Si vous réglez le sélecteur de mode sur VCR/CAMERA pendant la recharge, la recharge s’arrêtera.
•Si le témoin CHARGE ne s’allume pas ou clignote, vérifiez que la batterie est fixée correctement à l’adaptateur secteur/chargeur. Si elle n’est pas rattachée correctement, elle ne se rechargera pas.
Indication des tempsPendant la recharge, vous pouvez vérifier le temps de recharge sur la fenêtre d’affichage. Une minute après le début de la recharge, BATTERY LIFE s’allume. Le temps indiqué désigne l’autonomie de la batterie lorsque vous prenez des photos avec le viseur. L’autonomie sera plus courte si vous utilisez l’écran LCD.
Appuyez sur DISPLAY CHANGE pendant la recharge.A chaque pression de cette touche, l’affichage change de la façon suivante.Autonomie lorsque la batterie rechargée est rattachée à un appareil électronique “InfoLITHIUM”
Ce temps n’est pas indiqué si l’autonomie est inférieure à 5 minutes.
Temps restant jusqu’à une recharge normaleLe temps d’une recharge normale n’est plus indiqué lorsque la recharge normale est terminée.
Temps restant jusqu’à une recharge complèteLe temps d’une recharge complète n’est plus indiqué lorsque la recharge complète est terminée.
Remarques
•Le temps indiqué est approximatif même quand la batterie est rechargée entre 10 °C et 30 °C. Selon les conditions d’utilisation et les circonstances, le temps peut être différent du temps réel.
•“– – –
–Il y a une différence entre le temps affiché et le temps de recharge réel. Continuez la recharge, si cet indicateur apparaît.
•Une recharge complète prend environ une heure. Si vous détachez la batterie entre la recharge normale et la recharge complète, le temps risque de ne pas être indiqué correctement lors de la recharge suivante.
•Si une batterie n’a pas été utilisée pendant longtemps, l’autonomie indiquée et le temps de recharge complète peuvent être inexacts. C’est normal. Dans ce cas, rechargez une nouvelle fois la batterie. Les temps seront alors corrects.
•Quand vous raccordez une batterie complètement rechargée à cet appareil, “TIME TO CHG FULL 1h”peut apparaître sur la fenêtre d‘affichage. Il ne s’agit pas d’une anomolie.
•Il faut attendre un certain temps après une pression de DISPLAY CHANGE pour que le temps apparaisse.
•Pour connaître l’autonomie d’une batterie neuve,
Pour utiliser l’appareil vidéo
Voir l’illustration C.Pour le raccordement,2Raccordez le cordon d’alimentation ou le cordon
3Raccordez le cordon d’alimentation à une prise secteur ou à une douille
Faites glisser la plaquette de connexion B tout en appuyant dessus. Pour retirer la plaquette de connexion,
Ouvrez le couvercle et introduisez la fiche D. Pour retirer la fiche, tirez dessus.
Remarques
•Si vous réglez le sélecteur de mode sur CHARGE pendant l’utilisation de l’appareil vidéo, l’alimentation sera coupée.
•Vous ne pouvez pas recharger la batterie quand elle est sur l’appareil vidéo et l’alimente.
•Eloignez l’adaptateur de l’appareil vidéo s’il perturbe l’image.Remplacement du fusible
Si l’appareil ne fonctionne pas correctement lorsque rous utilisez le DCC- VQ1, vérifier si le fusible n’a pas sauté. Si le fusible a sauté,
Remarques
•Remplacez le fusible par un fusible de la même intensité (4 A, 125 V).•Si la douille de
•Si le fusible saute juste après avoir été remplacé, consultez votre revendeur Sony.
En ce qui concerne la polarité de la masse de la voiture, la tension de la batterie de voiture ou autre, consultez votre concessionnaire auto.