For DRN-XM01C/XM01CK
Connecting the Unit to the Cigarette Lighter Socket
Using the Car Connecting Pack
1 | Turn down the volume of the car cassette deck. |
2 | Set the tape selector to the normal (TYPE I) position, and the |
For DRN-XM01R
Connecting the Unit to your Car with a RF Modulator
For the DRN-XM01C/XM01CK/XM01R
When the Installation and Connections Have Been Made
For DRN-XM01H/XM01HK
Using the Unit on House Current
Use the AC power adaptor and the audio cord supplied with
Replacing the Lithium Battery into the Remote Commander
Replace the battery when the buttons on the remote commander do not work. Remove the old battery and insert a new one.
Precautions
• Do not install the unit where: |
– the ambient temperature exceeds 55°C (131°F). |
– it will be exposed to direct sunlight or hot air from a heater. |
– it will be exposed to rain, water, or high humidity. |
– it will be exposed to a lot of dust. |
Car cassette deck
to a cassette insertion slot
| DOLBY NR, REPEAT, or BLANK SKIP switch to the OFF |
3 | position if such are equipped. |
Insert the car connecting pack into the cassette deck. | |
4 | Start playback on the car cassette deck. |
5 | Adjust the volume. |
to the +12 V power |
| |
terminal which is |
| |
powered when the |
| |
ignition key switch is |
| |
in the accessory |
| |
position | Red | |
Be sure to connect | ||
| ||
the black earth lead |
|
Fuse (1 A)
Black |
to a metal point |
on the car |
After installing and connecting the unit, run cord so as not to interfere with the operation of the vehicle.
Run and fix the cord on the passenger side of the center console with the supplied cord clamp.
2
1
– it will be subject to excessive vibration. |
– hinder normal driving activities. |
– jeopardize the passengers. |
• Be sure to turn off the power of each component before making the |
connections. |
Car connecting pack
to the ANT
SAT jack
to the
LINE OUT
jack
Cradle
to a cigarette lighter socket
Power lamp
Car battery cord
SAT
TER
XM antenna
to the ANT TER jack
to the DC IN 6V jack
If no sound is heard or the car connecting pack is removed, change the playback direction on the car cassette deck.
To Remove the Car Connecting PackPress the Z (eject) button of the car cassette deck.
Note
You cannot use this car connecting pack with certain car cassette decks.
Fuse Replacement
| Fuse (1 A) | to tighten |
|
| to remove |
Cigarette lighter plug | End of the plug |
|
to it first. |
XM antenna |
SAT
to the ANT SAT jack
Cradle
to the LINE OUT jack
Power connecting cord (Supplied)
POWERANT
| RF Modulator | |
TER | DC OUT | AUDIO |
| ||
to the ANT TER jack |
|
|
to the DC IN 6V jack |
|
Car audio | Speaker | |
system | ||
Antenna connecter | ||
|
Connect it as follows when a diversity antenna is used for the car audio.
TOYOTA
Connect to the bigger antenna connector.
NISSAN
The optional antenna converter cord
Others
The optional antenna converter cord may be required. Check with the retailer.
to the car antenna
Cord clamp*
*• Clean the mounting surface before installing the cord clamp.
•Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off because of weak attachment.
Note
Make sure the cord does not get caught in the sliding rails under the front seats or the front doorsills as this may cause the cord to be severed.
| Tighten the screw at the | |
To the stand | bottom of the home stand | |
to secure the cradle. | ||
receptacle at | ||
| ||
the bottom of |
| |
the cradle |
|
to the input jacks | to an AC outlet |
of the audio |
|
equipment |
|
XM antenna |
|
3
1Insert a long and thin object into the hole, then pull out the lithium battery holder.
2Place the lithium battery with the positive (+) side facing up.
3Insert the battery holder into the remote commander until it clicks.
Battery life | (Approx.) |
Sony lithium battery CR2025 | 1 year |
Notes on lithium battery
• Keep the lithium battery out of reach of children. Should the battery be |
swallowed, immediately consult a doctor. |
• Wipe the battery with a dry cloth to assure good contact. |
• Be sure to install the battery in the correct polarity position. |
Be sure to check that the voltage of the equipment connected to this unit is correct. Incorrect voltage may cause the equipment to malfunction.
•This unit is designed for negative ground 12 or 24 V DC operation only.
•Avoid high temperatures, such as direct sunlight or hot air from the heater.
•You cannot use this unit with some car cassette deck.
•Used with some car cassette decks, the car connecting pack may rattle. This is not a malfunction of the car connecting pack.
Note on the DC plug of the car battery cord
This car battery cord uses a unified polarity type plug (JEITA standard). Damage will occur if it is connected to a DC power input jack without the
!polarity symbol or with another symbol.
For•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, disconnect the earth terminal of the car battery to avoid short circuits.
•Connect the red power input leads only after all other leads have been connected.
•Be sure to connect the red power input lead to the positive 12 V power terminal which is powered when the ignition switch is in the accessory position.
•Run all earth wires to a common earth point.
When the electric power is supplied to the car battery cord, the power lamp lights up.
Notes
• Route the cords so that they will not interfere with your driving. |
• Take care not to accidentally insert a portion of the car connecting pack |
cord into the cassette insertion slot. This may cause the cord to break or |
damage the car cassette deck. |
• To disconnect the cord from your audio equipment, pull it out by |
grasping the plug. Never pull it by the cord. |
• If the inside of the cigarette lighter socket is dirty with cigarette ash, the |
cigarette lighter plug may be heated due to abnormal contact. Be sure |
1Pull the cigarette lighter plug out of the cigarette lighter socket.
2Detach the end of the plug by turning it counterclockwise.
3Replace the fuse with a new one.
4Reattach the end of the plug by turning it clockwise firmly.
Notes
•When replacing the fuse, be sure to use one with the correct amperage, as stated on the fuse case. (1 A, 125 V, 20 mm)
•Do not use a piece of wire instead of a fuse.
•If the replaced fuse opens again, consult your dealer.
Fuse Replacement
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction.
Warning
Use a fuse with the specified amperage rating. Use of a higher amperage fuse may cause serious damage.
This unit changes the signal of the XM satellite radio broadcast into an FM frequency and outputs the sound through an FM tuner. There may be interference noise while playing the receiver, when the frequency selected for the receiver is used for transmitting the actual FM broadcast. In such a case, change the transmitting frequency on the unit. The
Audio cord | AC power adaptor |
| |
SAT | TER |
to the ANT | to the ANT |
SAT jack | TER jack |
to the LINE | to the DC IN 6V jack | |
OUT jack | ||
|
• Do not hold the battery with metallic tweezers, as doing so may cause a |
• Do not break up the battery or throw it into a fire, which might cause it |
to explode. |
Carefully dispose of the used battery. |
Note
When the unit is not to be used for a long period of time, remove the battery to avoid damage from battery leakage and corrosion.
Specifications
For
On installing the AC power adaptor
Do not place the AC power adaptor in a location where it is subject to:
–extreme high temperature (E.g., in a car with its windows closed)
–direct sunlight or near a heat source
–mechanical vibration or shock
–a magnetic field (E.g., near a magnet, speaker, or TV)
–excessive dust.
On operating the AC power adaptor
to clean the inside of the cigarette lighter socket before inserting the |
plug. |
• After using the receiver, eject the car connecting pack from the car |
cassette deck and disconnect the car battery cord from the receiver and |
the cigarette lighter socket. |
• Do not use the receiver when the car’s engine is not running. |
This RF modulator supplies power to the receiver and detects the on/off state by monitoring the load of the power. When the receiver is turned on, the RF modulator automatically cuts off the antenna line and directly outputs the sound of the receiver to the car audio with the selected FM frequency. This prevents the sound from disturbing the FM broadcast signal. When the receiver is turned off, the antenna line is connected to the car audio. Besides, you can set the RF modulator to always cut off the antenna line and output the XM radio sound to the car audio, in this case, you cannot hear the normal FM broadcast.
POWER SEL (select)
switch
POWER
SEL
ON 2 1
1: Normal use (detecting more than 100 mA load)
2: Not used (detecting more than 50 mA load) ON : Not used (cutting off the antenna line)
Frequency select switch
F.SEL |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 2 3 4 |
| 87.7 MHz |
|
| |||
|
|
|
|
| (Default) |
|
|
|
|
|
|
| 1 2 3 4 |
| |
|
|
|
|
|
| ||
1 2 3 4 |
| 88.5 MHz | |||||
| 87.9 MHz | ||||||
|
|
|
|
|
|
|
|
1 2 3 4 |
| 88.1 MHz | 1 2 3 4 | 88.7 MHz | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 2 3 4 |
|
1 2 3 4 |
| 88.3 MHz | 88.9 MHz |
Note
When you change the frequency on the unit, be sure to tune your FM tuner to the newly selected one.
Note on the DC plug of the AC power adaptor
This AC power adaptor uses a unified polarity type plug (JEITA standard). Damage will occur if it is connected to a DC power input jack without the !polarity symbol or with another symbol. If the jack of your audio equipment does not match the AC power adaptor, consult your dealer.
Symbol of unified polarity type jack
Placement of the Home AntennaThe satellite is located in the south sky. Place the antenna as follows for proper reception:
–Outside the house
–Place the antenna in an area where there are no obstacles within 20 - 60 degrees facing the southern sky.
–On a flat surface so that it is parallel to the ground.
When you place it indoors, or if there is a building or tree in the direction of the satellite, the antenna may not be able to receive the radio wave. Depending on where you live, you may be able to receive radio waves that are retransmitted by ground repeaters.
Accessories supplied
XM antenna (1)
Remote commander (1)
For
Car stand (1) Screw (5) Cover (1)
Water proof cushion (1) Cable guide (3)
Cord clamp (4)
Cushion with the
For
Car connecting pack (1) For
RF modulator (1)
For
Home stand (1) Audio cord (1)
AC power adaptor (1)
Optional accessories
AC power adaptor
Car battery cord
Car connecting pack
•Make sure the current and voltage of the equipment matches that of the outlet.
•For safety, if the input current is too high, the unit will automatically shut down.
•Do not use the unit near a TV set. If you place equipment too close to the unit while they are being used, you may experience some interference.
•To prevent damage, be careful not to drop or otherwise cause a mechanical shock to the unit.
•After using, disconnect the unit from the wall outlet and the equipment.
•Disconnect the unit from the AC outlet by pulling on the plug. Do not pull on the cord.
•To avoid
•Use only the recommended AC power adaptor.
For all CustomersOn cleaning
•Clean the unit with a soft, dry cloth. If the unit is very dirty, wipe it off with a soft cloth lightly moistened with a mild detergent solution, and then wipe with a soft dry cloth.
•Do not use any type of solvent such as alcohol, thinner, or benzine as it may damage the finish of the cabinet.
•If you use any chemical cleaner, observe the instructions provided with the product.
•If the cabinet of the unit is splashed with any type of solvent such as insecticide, or remains in contact for a long time with rubber or vinyl, the finish or the cabinet may be damaged.