FM |
|
AM | MHz |
PM | kHz |
BAND/CLOCK RADIO/LINE IN | POWER |
FM ANTENNA |
| LINE OUT LINE IN |
|
EXT INT
75
FM ANTENNA selector
AC power cord
| /TIM |
| |
E | E | S | |
N |
|
| |
U |
|
| E |
|
| T | |
T |
|
|
|
i
|
| LU |
|
|
|
| |
| O | M |
|
|
| ||
| V |
|
| E |
|
|
|
M |
|
|
|
|
| A | X |
I |
|
|
|
|
| ||
| N |
|
| M |
| ||
|
| ON |
|
|
|
| |
| T | E |
|
|
|
| |
O |
|
|
|
| H |
| |
L |
|
|
| G |
|
| |
W |
|
| I |
|
| ||
|
|
|
| H |
|
|
|
LINE IN jack.
5Adjust the volume using VOLUME.To return to the radio
Press RADIO/LINE IN.
The frequency is shown in the display.To record with LINE OUT
1Connect the LINE OUT jack of the unit to the line in jack of the external equipment using the audio connecting cable (supplied).
FM ANTENNA | LINE OUT LINE IN |
EXT INT
75
Audio connecting cable (supplied)
To external equipment
2Press POWER to turn on the radio.3Tune the unit to the radio station that you want to record.4Start to record on the connected equipment.Notes
• Refer also to the connected equipment’s manual. |
• The supplied audio connecting cable may not be used |
with some external equipment. In this case, use a cord |
suitable for the external equipment you are using. |
• LINE OUT signal of AM broadcasts is output in |
monaural (same sound is output from both head- |
phones). And LINE OUT signal of FM stereo |
broadcasts is output in stereo. |
• The sound quality of LINE OUT signal is constant |
regardless of the position of TONE, and the output |
•When you listen to the radio with external equipment connected, turn off the connected equipment because noise may be caused. If noise continues, even when the equipment is turned off, disconnect and place the external equipment away from the unit.
•If there are line out and headphone jacks on external equipment, connect to the line out jack.
•If you connect with the headphone jack of the external equipment, some equipment may not perform tone switch function (e.g., bass boost, equalizer etc.).
Specifications
Time display
Frequency range FM : 87.5 - 108 MHz AM : 530 - 1 710 kHz
Speaker
Approx. 7.7 cm ( 3 1/8 inches) dia. 4 Ω
Output
LINE OUT jack (ø 3.5 mm stereo minijack)
i(headphones) jack (ø 3.5 mm stereo minijack)
Input
LINE IN jack (ø 3.5 mm stereo minijack)
Antenna terminal
75 Ω external antenna terminal for FM
Power output
4 W (at 10 % harmonic distortion)
Power requirements
120 V AC, 60 Hz
Dimensions
Approx. 300 ⋅ 120 ⋅ 170 mm (w/h/d)
(11 7/8 ⋅ 4 3/4 ⋅ 6 3/4 inches) not incl. projecting parts and controls
Mass
Approx. 2.3 kg (5 lb 1.13 oz)
Supplied accessory
Audio connecting cable (1)
Design and specifications are subject to change without notice.
Setting the clock
1Plug in the unit.The display will flash “AM 12:00”.
2Press POWER to turn off the radio when it is turned on.3Press and hold BAND/CLOCK for a few seconds.You will hear a beep and the hour will start to flash in the display.
4Turn TUNE/TIME SET right or left until the correct hour appears in the display.
5Press BAND/CLOCK once.The hour is set and the minutes start to flash.
6Repeat steps 4 and 5 to set the minute.Two short beeps sound, “:” starts flashing, and the clock starts operating.
If you do not set the clock within 65 seconds, the setting is canceled.
Playing the radio
You can use an external FM antenna although the AC power cord functions as an FM antenna.
When you use an external FM antenna, connect the antenna cable to FM ANTENNA connector on the rear of the radio and then set FM ANTENNA selector to EXT. When you do not use an external FM antenna, set FM ANTENNA selector to INT.
1Press POWER to turn on the radio.If “LINE” is displayed, press RADIO/LINE IN so that the frequency appears.
2Press BAND/CLOCK to select the band AM or FM.3Turn TUNE/TIME SET right or left to tune in to a desired frequency.Two short beeps sound when the minimum frequency of each band is received during tuning.
Improving the reception
FM: The AC power cord functions as an FM antenna. Select FM ANTENNA selector to INT and extend the AC power cord fully to improve FM reception.
AM: Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built into the unit.
Notes
•Do not play the unit over a steel desk or metal surface, as this may lead to interference of reception.
•If using an external FM antenna, set FM ANTENNA selector to EXT, then connect the 75 Ω coaxial cable (not supplied) to FM ANTENNA (75 Ω) connector on the rear of the unit.
•To receive FM signals via cable available from some cable TV providers, contact your cable TV company for assistance.
Connecting external equipment
To listen to sound
1Connect the LINE IN jack of the unit to the line out jack or headphone jack of the external equipment using the audio connecting cable (supplied).
level is constant regardless of the position of |
VOLUME. |
4 Adjust the volume using VOLUME. | FM ANTENNA | LINE OUT LINE IN | |
5 Set the tone using TONE. | EXT | INT | |
|
| ||
To adjust the tone, turn TONE to LOW/HIGH. |
|
| |
To listen with the | 75 |
| |
|
| ||
headphones |
|
| |
You can enjoy the radio and external equipment | Audio connecting cable | ||
connected to the line in by the headphones (not | (supplied) |
| |
supplied). Connect the headphones (not supplied) | To external |
| |
to the i (headphones) jack. The speaker is |
| ||
equipment |
| ||
deactivated when the headphones are connected. |
| ||
2 Press POWER to turn on the radio. | |||
The headphones output AM broadcasts in | |||
monaural (same sound is output from both |
|
| |
headphones), while FM stereo broadcasts are |
|
| |
output in stereo. |
|
|