
To prevent fire or shock hazard,
do not expose the unit to rain
or moisture.
To avoid electrical shock, do not
open the cabinet. Refer
servicing to qualified personnel
only.
Mains cord must only be changed at
qualified service shop.
For the Customers in the U.S.A.
This symbol is intended to
alert the user to the
presence of uninsulated
“dangerous voltage”
within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to
alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature
accompanying the
appliance.
WARNING
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful
interference in a residential
installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
–Reorient or relocate the receiving
antenna.
–Increase the separation between the
equipment and receiver.
–Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
–Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.
Before you begin
Thank you for purchasing Sony
RM-D100K! The RM-D100K is the
remote control, timer, and digital
input/output adaptor kit for the
digital audio tape-corder TCD-D100.
Before operating the unit, please read
this manual thoroughly and retain it
for future reference.
This adaptor kit is designed to be
used with the digital audio tape-
corder TCD-D100. It can also be
used with the digital audio tape-
corder TCD-D8/D7/D3.
Please attention to the following.
Notes
Be sure to operate the TCD-D100 on
house current.
•Using batteries may interfere with
the input/output signals and
may cause a malfunction of the
remote commander.
•It is impossible to operate the
TCD-D8/D7/D3 during low-
power consumption mode.
Features
With the RM-D100K connected to
TCD-D100, you can:
–Enjoy wireless control of the
TCD-D100 (including direct
selecting of desired programs, music
scanning, and record muting
operations);
–Connect to other audio equipment
using digital input/output
connectors (both optical and coaxial
digital);
–Make timer-activated recordings and
playbacks on the TCD-D100 (when
used with an audio timer, not
supplied).
System Adaptor Kit3-859-925-11(1)RM-D100K
Sony Corporation © 1997 Printed in JapanOperating Instruction
Mode d’emploi
A
aRemote control/timer/digital input/output adaptor
RMR-D100 (Front side)Adaptateur de télécommande/minuterie/entrée/sortienumériques RMR-D100 (Façade)Location and
Function of Controls
Remote control/timer/digitalinput/output adaptorRMR-D100 (main unit)Front side (See fig. A-a)1OPERATE switch and lampTo remote control the TCD-D100,
set the switch to either STANDBY
or ON. To use the input/output
connectors or to make timer-
activated recording or playback,
set it to ON.
2Remote sensor3INPUT SELECT selectorSelects the input signals of the
TCD-D100 (either digital or
analog).
4TIMER selectorRear side (See fig. A-b)5Optical input/output jacks6OPTICAL INPUT (opticaldigital input) jack7OPTICAL OUTPUT (opticaldigital output) jack*8Special 7-pin connector9DIGITAL INPUT selector!ºCOAXIAL INPUT (coaxialdigital input) jack!¡COAXIAL OUTPUT (coaxialdigital output) jack*!™ Power supply cord* Whichever position is selected on
the DIGITAL INPUT selector, the
signal of TCD-D100 is output
simultaneously from the OPTICAL
OUTPUT and COAXIAL OUTPUT
jacks.
Remote Commander RMT-D101(See fig. A-c)!£START ID (AUTO, WRITE,ERASE, RENUMBER) buttonsFor writing or erasing a start ID
and renumbering program
numbers.
!¢Numeric buttons, CLEAR,MUSIC SCAN buttonsFor direct selecting.
!R buttonFor record-muting.
!§CD (P, =, +) buttonsFor remote-control operation of
Sony CD players connected to this
unit.
!¶CD SYNCHRO (STOP, START,STANDBY) buttonsFor synchronized recording with
SONY CD players connected to
this unit.
!•COUNTER (MODE, RESET)buttons(have the same function as the
TCD-D100 buttons.)
!ªTape operation buttonsr, p, (, P, buttons:(have the same function as the
TCD-D100 buttons.)
=, + buttons:AMS Function (You can search
for the beginning of a track by
pressing = or + buttons in
any mode.)
0, ) buttons:For rewind and fast-forward
during stop mode. For review
and cue during playback mode.
(High speed review and high
speed cue are not possible.)
Precautions
On safety•Before connecting the RMR-D100
remote control adaptor to the wall
outlet, check to be sure that the
unit’s operating voltage is the same
as your local power supply (see
“Specifications”). Use only the
supplied power cord and no other
type.
•The nameplate indicating operating
voltage, power consumption, etc., is
located on the bottom exterior of the
RMR-D100.
•To operate the commander, use two
R6 (size AA) batteries. Never use
any other type.
•Should any liquid or solid object fall
into the cabinet, unplug the
RMR-D100 and have it checked by
qualified personnel before operating
it any further.
•Unplug the RMR-D100 from the wall
outlet if it is not going to be used for
several days or more. To disconnect
the cord, pull it out by the plug;
never pull the cord itself.
•To avoid damage from battery
leakage, remove the batteries from
the commander when it is not going
to be used for several days or more.
•The unit is not disconnected from
the AC power source (mains) as long
as it is connected to the wall outlet,
even if the unit itself has been turned
off.
On installationDo not install the kit near heat sources
such as radiators or air ducts, or in
locations subjects to direct sunlight,
excessive dust, excessive moisture,
mechanical vibrations or shock.
On cleaningClean the kit with a lightly dampened
soft cloth. Use a mild household
detergent. Never use strong solvents
such as thinner or benzine as they
might damage the unit’s exterior
finish.
If you have any questions or problems
concerning your unit that is not
covered in this manual, please consult
your nearest Sony dealer.
b(Rear side)
(Arrière)cRemote Commander RMT-D101
Télécommande RMT-D1011
2
3
4
9
!…
!`
!“
5
7
6
8
!⁄
!
!£
!»
!¥
!¢
!ƒ
START ID
Apparaten bortkopplas inte fran spänningskällan så länge som den är ansluten till
vägguttaget, även om själva apparaten her stängts av.
Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en
stikkontakt, som er tændt-også selvom der er slukket på apparatets netafbryder.
Appratet er forsynet med en speciel netledning, der kun ma udskiftes af et autoriseret
serviceværksted.
AVERTISSEMENTAfin d’éviter tout risque
d’incendie ou d’électrocution, ne
pas exposer cet appareil à la
pluie ou à l’humidité.
Afin d’éviter tout risque
d’électrocution, ne pas ouvrir le
coffret. Pour toute réparation,
faire appel à un professionnel
uniquement.
Avant propos
Merci d’avoir choisi le Sony
RM-D100K! Le RM-D100K est un
ensemble comprenant entre autres
l’adaptateur de télécommande,
minuterie et entrée/sortie numérique,
conçu pour l’enregistreur
audionumérique TCD-D100.
Avant la mise en service de cet
appareil, prière de lire attentivement
ce mode d’emploi que l’on conservera
pour toute référence future.
Cet ensemble adaptateur est conçu
pour être utilisé avec l’enregistreur
audionumérique TCD-D100. Il
peut être également utilisé avec les
TCD-D8/D7/D3.
Veuillez tenir compte des
recommandations suivantes.
Remarques
Veillez à utiliser le TCD-D100 sur le
courant secteur.
•L’utilisation des piles peut
perturber le signal d’entrée/sortie
et le fonctionnement de la
télécommande.
•Il est impossible de faire
fonctionner le TCD-D8/D7/D3
dans le mode économique.
Caractéristiques
Quand le RM-D100K est raccordé au
TCD-D100, vous pouvez:
–commander à distance le TCD-D100,
en particulier sélectionner des
programmes, rechercher des
passages et enregistrer des passages
silencieux.
–connecter l’appareil à d’autres
appareils audio par les prises
d’entrée/sortie numériques (les
deux prises sont de type optique et
coaxial numérique).
–programmer un enregistrement ou
la lecture sur le TCD-D100, dans la
mesure où vous avez raccordé une
minuterie audio (non fournie).
Emplacement et
fonctions des
commandes
Adaptateur télécommande/minuterie/entrée/sortienumériques RMR-D100(appareil principal)Façade (Voir fig. A-a)1Commutateur et voyantOPERATEPour la commande à distance du
TCD-D100, réglez le commutateur
sur STANDBY ou ON. Pour
utiliser les prises d’entrée/sortie
numériques ou pour un
enregistrement/lecture
programmé, réglez-le sur ON.
2Capteur de signauxinfrarouges3Sélecteur INPUT SELECTPermet de sélectionner le signal
d’entrée du TCD-D100
(numérique ou analogique).
4Sélecteur TIMERArrière (Voir fig. A-b)5Prises d’entrée/sortieoptiques6Prise OPTICAL INPUT (entréenumérique optique)7Prise OPTICAL OUTPUT*(sortie numérique optique)8Connecteur spécial à 7broches9Sélecteur DIGITAL INPUT!ºPrise COAXIAL INPUT(entrée numérique coaxiale)!¡Prise COAXIAL OUTPUT*(sortie numérique coaxiale)!™ Cordon d’alimentationsecteur* Quelle que soit la position de réglage
du sélecteur DIGITAL INPUT, le
signal du TCD-D100 est fourni
simultanément par les prises
OPTICAL OUTPUT et COAXIAL
OUTPUT.
Télécommande RMT-D101(Voir fig. A-c)!£Touches START ID (AUTO,WRITE, ERASE, RENUMBER)Pour inscrire ou effacer des
indices de départ et renuméroter
un programme.
!¢Touches numériques,touches CLEAR, MUSICSCANPour la sélection directe d’un
programme.
!Touche RPour enregistrer un passage
silencieux.
!§Touches CD (P, =, +)Pour le contrôle à distance d’un
lecteur CD Sony raccordé à cet
appareil.
!¶Touches CD SYNCHRO(STOP, START, STANDBY)Pour l’enregistrement
synchronisé avec un lecteur CD
Sony raccordé à cet appareil.
!•Touches COUNTER (MODE,RESET)Ces touches ont les mêmes
fonctions que les touches du
TCD-D100.
!ªTouches d’exploitationTouches r, p, (, P:Ces touches ont les mêmes
fonctions que les touches du
TCD-D100.
Touches =, +:Fonction AMS (permet de
localiser le début d’une plage en
appuyant sur les touches = ou
+ dans n’importe quel mode.)
Touches 0, ):Pour rembobiner ou bobiner la
bande à partir du mode d’arrêt.
Pour la recherche arrière ou avant
en cours de lecture. (La recherche
rapide avant et arrière n’est pas
possible.)
Précautions
Sécurité•Avant de raccorder l’adaptateur de
télécommande RMR-D100 à une
prise murale, assurez-vous que sa
tension de fonctionnement est
identique à la tension secteur locale
(voir “Spécifications”). Utilisez
seulement le cordon d’alimentation
fourni à l’exclusion de tout autre.
•La plaque signalétique indiquant la
tension de fonctionnement, la
consommation et d’autres
paramètres, se trouve sous le RMR-
D100.
•Pour faire fonctionner la
télécommande, utilisez deux piles
R6 (format AA) à l’exclusion de
toute autre.
•Si un liquide ou un solide tombe
dans le coffre, débranchez le RMR-
D100 et faites-le vérifier par un
professionnel avant de le remettre en
service.
•Débranchez le RMR-D100 de la prise
murale si vous prévoyez de ne pas
l’utiliser pendant quelques jours.
Pour le débrancher, tirez sur la fiche.
Ne pas tirer sur le cordon
proprement dit.
•Pour éviter tout dommage causé par
l’électrolyte des piles, enlevez les
piles si vous prévoyez de ne pas
utiliser la télécommande pendant un
certain temps.
•L’adaptateur n’est pas débranché de
la source d’alimentation (secteur)
tant qu’il est raccordé à une prise
murale, même s’il a été arrêté.
InstallationNe pas installer l’ensemble près de
sources de chaleur, comme un
radiateur ou une sortie d’air chaud, ou
dans des lieux exposés à la lumière
directe du soleil, à une poussière et
une humidité excessives, à des
vibrations ou à des chocs.
NettoyageNettoyez l’ensemble avec un chiffon
doux légèrement mouillé d’un
détergent domestique neutre. Ne
jamais utiliser de solvants, comme les
diluants ou la benzine, car ils risquent
d’endommager la finition.
Pour toute question ou problème
concernant cet appareil, non couverts
dans le mode d’emploi, veuillez
consulter votre revendeur Sony.
Specifications
SystemInfrared pulse method
Power requirementsRMR-D100:
120 V AC, 60 Hz (the USA
model)
230 V AC, 50 Hz (other models)
RMT-D101:
DC 3 V, two R6 (size AA)
batteries
Power consumption2.2 W (RMR-D100)
InputsDigital coaxial jack (phono-jack)
Digital optical jack (Rectangular-
shaped optical jack)
OutputsDigital coaxial jack (phono-jack)
75 ohms, 0.5 Vp-p, ±20%
Digital optical jack (Rectangular-
shaped optical jack)
wavelength: 680 nm, –18 dBm
MassRMR-D100: approx. 360 g (12.7 oz)
RMT-D101: approx. 130 g (4.6 oz)
including batteries
DimensionsRMR-D100: approx.
83 × 35 × 117 mm (w/h/d)
(3 3/8 × 1 7/16 × 4 5/8 inches)
including projecting parts
RMT-D101: approx.
45 × 26 × 210 mm (w/h/d)
(1 13/16 × 1 1/16 × 8 3/8 inches)
including projecting parts
Supplied accessoriesR6 (Size AA) batteries (2)
Accessories not suppliedDigital connecting cord (phono-plug)
VMC-10HG (1 m)
Digital cable for optical transmission
(optical plug) POC-5A/5AB (0.5 m),
POC-10A/10AB (1 m),
POC-15A/15AB (1.5 m)
* Your dealer may not handle the
above listed accessories. Please ask
the dealer for detailed information.
Design and specifications are subject
to change without notice.
Spécifications
SystèmeImpulsions infrarouges
AlimentationRMR-D100:
120 V CA, 60 Hz
(modèle pour les Etats-Unis).
230 V CA, 50 Hz
(autres modèles)
RMT-D101:
3 V CC, deux piles R6 (format
AA)
Consommation2,2 W (RMR-D100)
EntréesPrise coaxiale numérique
(prise cinch)
Prise optique numérique
(prise rectangulair optique)
SortiesPrise coaxiale numérique
(prise cinch) 75 ohms, 0,5 Vc-c,
±20%
Prise optique numérique
(prise rectangulair optique)
longueur d’onde: 680 nm, –18 dBm
PoidsRMR-D100: env. 360 g (12.7 on.)
RMT-D101: env. 130 g (4.6 on.)
avec les piles
Dimensions hors toutRMR-D100: env. 83 × 35 × 117 mm
(l/h/p)
(3 3/8 × 1 7/16 × 4 5/8 pouces)
compris pièces en saillie
RMT-D101: env. 45 × 26 × 210 mm
(l/h/p)
(1 13/16 × 1 1/16 × 8 3/8 po.)
compris pièces en saillie
Accessoires fournisPiles R6 (format AA) (2)
Accessoires non fournisCordon de liaison numérique
(à fiches cinch)
VMC-10HG (1 m)
Câble numérique pour transmission
optique (à fiche optique)
POC-5A/5AB (0,5 m),
POC-10A/10AB (1 m),
POC-15A/15AB (1,5 m)
* Votre revendeur n’aura peut-être
pas en stock tous les accessoires
indiqués. Consultez-le pour les
détails à ce sujet.
La conception et les spécifications
peuvent être modifiées sans préavis.