Calibration Procedures Teledyne API – T101 Operation Manual
182
Toggle to
set
number of
days
between
procedures
(1-367)
Toggle to set
delay time for
each iteration
of the
sequence:
HH:MM
(0 – 24:00)
SETUP X.X DELTA DAYS: 1
<SET SE T> EDIT EXIT
SETUP X.X DELT A DAYS: 1
0 0 2 ENTR EXIT
SETUP X.X DELTA DAYS:2
<SET SET> EDIT EXIT
SETUP X.X DELTA TIME00:00
<SET SE T> EDIT EXIT
SETUP X.X DELTA TIME: 00:00
0 0 :3 0 ENTR EXIT
SETUP X.X DELTA TIEM:00:3 0
<SET SET> EDIT EXIT
SETUP X.X STARTING TIME:14:15
<SET SET> EDIT EXIT
EXIT retu rns
to the SETUP
Menu
SETUP X.X DURATION:15.0 MINUTES
<SET SE T> EDIT EXIT
SETUP X.X DURATION 15.0MINUTES
3 0 .0 ENTR EXIT
SETUP X.X DURATION:30.0 MINUTES
<SET SET> EDIT EXIT
Toggle to
set
duration for
each
iteration of
the
sequence:
Set in
Decimal
minutes
from
0.1 – 60.0
SETUP X.X C
A
LIBRATE: OFF
<SET SE T> EDIT EXIT
SETUP X.X CALIBRATE: OFF
ON ENTR EXIT
SETUP X.X CA LIBRATE: ON
<SET SE T> EDI T EXIT
Toggle
button
between
Off and
ON
SETUP X.X S EQ 2) ZERO
–
SPAN, 2:00:3
0
PREV NEXT MODE SET EXIT
SAMPLE ENTER SETUP PASS : 818
8 1 8 ENTR EXIT
SETUP X.X PRIMARY SETUP MENU
CFG ACAL DAS RNGE PASS CLK M ORE EXI T
SETUP X.X SEQ 1) DI SABLED
NEXT MODE EX IT
SETUP X.X SEQ 2) DISABLED
PREV NEXT MODE EXIT
SETUP X.X MODE: DISABLED
NEXT ENTR EXIT
SETUP X.X MODE: ZERO
PREV NEXT ENTR EXIT
SETUP X.X MODE: ZERO
–
SPAN
PREV NEXT ENTR EXIT
SETUP X.X SE Q 2) ZERO–SPAN, 1:0 0:00
PREV NEXT MODE SET EXIT
SETUP X.X TIMER ENABLE: ON
SET > EDIT EXI T
SETUP X.X STARTING DATE: 0 1 – J AN–02
<SET SET> ED IT EXI T
SETUP X.X STARTING DATE: 0 1 – J AN–02
0 4 SEP 0 3 ENTR EXIT
Toggle to set
day, month &
year:
Format :
DD-MON-YY
SETUP X.X STA RTING DATE: 04–SEP –03
<SET SET> EDIT EX IT
Default
value is
ON
SETUP X.X STARTING DATE: 04–SEP–03
<SET SET> EDIT EXI T
SETUP X.X STARTING TIME:00:00
<
S
ET
S
ET> EDIT EXI T
Toggle to set
time:
Format : HH:MM
Thisisa 24
hr
SAMPLE R ANGE = 5 00.0 PPB H2S =XXX.X
< TST TST > CAL CALZ C ALS SETUP
With dynamic calibration turned on, the state of the internal setup variables dyn_Span and
DYN_ZERO is set to ON and the instrument will reset the slope and offset values for the
H2S response each time the AutoCal program runs. This continuous re-adjustment of
calibration parameters can often mask subtle fault conditions in the analyzer.
07266B DCN6485