Main
Page
Page
NOTICE
QUALIFIED PERSONNEL ONLY
UNINTERRUPTIBLE POWER SYSTEM (UPS)
Purpose
Toshibas Customer Support Center
i
Table of Contents
ii
iii
Page
1 Introduction
SAVE THESE INSTRUCTIONS
2
2 General Safety Instructions
2.1 Symbols
3
2.2 Signal Words
DANGER
2.3 Qualied Personnel
4
3 Important Safety Instructions
5
4 Safety Precautions
4.1 Disclaimer
6
4.2 General Maintenance
4.3 Transporting/Unpacking
BACKSIDE
8
4.4 Inspection/Storage
5 Installation Precautions
10
Item Environment standard
12
13
5.1 Wiring/Connection
14
6 Warning Labels
56875 FOR 80, 100, 150, 225 KVA
DANGER
AC VOLTAGE
REFER TO INSTRUCTION MANUAL FOR WIRE SIZE AND TIGHTENING TORQUE
USE COPPER CONDUCTORS ONLY! 12 13
(B)
DANGER
AC VOLTAGE
(D)
REFER TO INSTRUCTION MANUAL FOR WIRE SIZE AND TIGHTENING TORQUE
USE COPPER CONDUCTORS ONLY! 12 13
Page
Page
18
7 Weight and Dimensions
1-Weightsareapproximate.
Model Unit Shipping
8 Transporting
20
8.1 Transporting By Crane
8.1 Transporting By Crane
21
8.2 Transporting By Forklift
22
9 Storage/Operating Environment
24
25
9.2 Maintenance Precautions
26
9.3 Disposal
DANGER
10 Installation
Page
29
10.3 Anchor Bolts
80/100/125 kVA
150/225 kVA
300 kVA
11 UPS Wiring
11 UPS Wiring
11 UPS Wiring
32
11.1 80/100/125 kVA Terminal Blocks and Power Cables
Block Number Cable Size (Min-Max)2Tightening Torque
1 2 3 4 5 6 7 8 9 10 11 12 13
Block Number Cable Size (Min-Max) 2Tightening Torque
34
11.2 150, 225, 300, and 500 kVA Buss Strip Terminals and Power Cables
35
8
AC OUTPUT
+
BATTERY
36
Block Number Cable Size (Min-Max) Tightening T orque
38
Bus Number Cable Size (Min-Max) Tightening T orque
39
11.3 UPS Power Cable Conduit Landing Plates
40
Page
42
11.4 External Breakers
C O
input BReakeR R
Output BReakeR R
G8000 - 80/100 kVA
G8000 - 300 kVA
G8000 - 150/225 kVA
G8000 - 500 kVA
Page
45
The UPS battery cabinet and bypass breaker should be wired as shown below in Figure 11.15.
11.7 Grounding Conguration
11.7.1 Recommended conguration (for 4 wire input with Input Neutral grounded)
46
FIGURE 11.16 - GROUNDING CONFIGURATION WITH INPUT NEUTRAL GROUNDED
B
FIGURE 11.17 - JUMPER CABLE BETWEEN THE NEUTRAL TERMINAL & GROUND BUS
Ground Bus Remove Jumper
47
11.7.2 Grounding Conguration (without input neutral)
11.7.3 Recommended Conguration (for delta-input)
48
11.7.4 Grounding Conguration (with corner-grounded delta-input)
49
12 UPS Specications
12.1 Specication Table
Input
Bypass
Battery
50
Output
Reliabil- ity
Environ- ment
Environ- ment (cont.)
Monitor- ing
EPO
Cong- uration
Page
13 Operator Interface
Table 13.1 shows the functions of the operating buttons on the graphic display panel.
# Name Function
Page
55
13.2 LCD/LED Indicators
56
13.3 LCD Indicators
Name Description
Page
Page
Page
60
13.6 LCD Scroll
14 Operating the UPS
62
14.1 Operation Types
Operation Description
14.2 Pre-operational Check
63
14.3 Startup Procedures
SYSTEM INITIALIZE
64
STEP 4
STEP 5
*
65
14.4 Switch Power Supply (UPS to Bypass)
66
14.5 Stop
Page
68
14.7 Changing Between Float Charge and Equalize Charge
69
14.8 Changing to Float Charge from Protection Charge (If applicable)
70
14.9 Emergency Power Off (EPO)
1. 2.
15 Troubleshooting
15.1 Types of Errors
Name Description
71
15.2 Faults and Warnings Data Screen
# Name Description
72
15.3 LCD Fault & Warning Displays
73
15.4 Fault Messages
ITEM LCD MESSAGE INDICATION DESCRIPTION
74
75
15.5 LCD Scroll (w/ faults or warnings)
# Name Function
76
15.6 Restoring UPS Operation
16 Periodic Maintenance/Parts Replacement
Page
79
Appendix A - Installation Planning Guides
80kVA IPG
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K08KK6XSxx)
80
Page
82
100kVA IPG
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K10KK6XSxx)
DC Backup Input (Battery -360VDC Nominal)
Page
84
85
125kVA IPG
TOSHIBA G8000 Series UPS
AC Output (480/277V 3-Phase / 4-Wire)
DC Backup Input (Battery -360VDC Nominal)
Alternate (Bypass) AC Input (480V 3-Phase / 4-Wire)
Primary AC Input (480V 3-Phase / 3-Wire)
TOSHIBA G8000 Series UPS
Installation Planning Guide for 125kVA UPS
TOSHIBA G8000 Series UPS
Installation Planning Guide for 125kVA UPS
88
150kVA IPG
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K15KK6XSxx)
Page
90
91
225kVA IPG
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K22KK6XSxx)
92
Page
94
300kVA IPG
Installation Planning Guide for 300kVA UPS
DC Backup Input (Battery -360VDC Nom.)
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K30KK6XSxx)
Page
Installation Planning Guide for 300kVA UPS
97
500kVA IPG
Installation Planning Guide for 500kVA UPS
DC Backup Input (Battery - 480VDC Nom.)
Standard System: 480V Input, 480Y/277V Output (P/N T80S3K50KK6XSxx)
Installation Planning Guide for 500kVA UPS
Installation Planning Guide for 500kVA UPS
Page
Page
Page
Page
Page
Appendix C - 500kVA Input- and Output- Cabinet Joining Instructions