To control a cable TV converter:
Program the remote control to recognize the brand of your converter. The shaded buttons in the illustration at right will then control the cable TV converter.
Press the CABLE button when you want to control the cable TV converter.
Programming the remote control for use with a VCR or a cable TV converter
The remote control provided with your TV is preprogrammed to operate Toshiba brand VCRs. You can program your TV remote control to operate other brands of VCRs and cable TV converters as well.
To program your TV remote control to operate
1.Refer to the VCR and cable TV converter code tables on pages
12–13 to find the corresponding code for your VCR or converter brand.
If more than one code is listed, try each one separately until you find the one that works.
2.Turn on the device (VCR or converter) whose code you are programming.
3.Press the corresponding device button (VCR or CABLE) and the ENT/CH RTN button at the same time. The device button will light up, indicating that it is in the program mode. Perform steps 4 and 5 while the button is lighted (about 20 seconds).
4.Point the remote control toward the VCR or converter, and press the Channel Number buttons to enter the
•If the correct code was entered, the VCR or converter will turn off.
•If the VCR or converter does not turn off, repeat steps 1–4 using another code.
When the correct code is entered, the lighted button will blink.
5.Press the corresponding device button (VCR or CABLE) to release the program mode.
6.Press TV to control the TV.
For future reference, write down the code numbers you used:
VCR code | _____________________ |
Cable code | _____________________ |
|
|
|
|
|
|
| POWER | POWER |
MTS |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| TIMER |
|
TV |
| CABLE VCR |
|
| Device buttons | |||
|
|
|
|
|
|
|
| |
1 |
|
| 2 |
| 3 |
|
| Channel yz |
4 |
|
| 5 |
| 6 |
| CH | |
|
|
|
|
| Channel | |||
7 |
|
| 8 |
| 9 |
|
| |
|
|
|
|
| Number | |||
|
|
|
|
| CH RTN | VOL | ||
|
|
|
|
|
| |||
100 |
|
| 0 |
| ENT |
|
| Enter |
|
| AP |
| RE |
|
| ||
| .C | T |
| S |
|
| ||
| C |
|
|
|
| ET |
| |
|
|
|
|
|
|
| E |
|
|
|
|
|
|
|
| X |
|
|
|
|
|
|
|
| I |
|
|
|
|
|
| ADV |
| T |
|
|
|
|
|
|
|
|
| |
FAV |
|
|
| MENU/ |
| FAV |
| |
- |
|
|
| ENTER |
| + |
|
ADV
Note:
•Each time you replace the batteries, you must reprogram the remote control.
•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does not respond after programming to any of the codes for your VCR brand, set the switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
Introduction |
|
|
|
|
|
Connecting | yourTV |
|
|
|
|
Usingthe | RemoteControl |
|
|
|
|
Settingup | yourTV |
|
|
|
|
UsingtheTV’s | Features |
|
|
|
|
Appendix |
|
|
|
|
|
Index |
|
|
|
11