ADDITIONAL INFORMATION ...................................................

Troubleshooting

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. When talking to the service center, the CDR- D651 may be needed. For details, contact your authorized YAMAHA dealer or service center.

SYMPTOM

CAUSE

REMEDY

 

 

 

The unit does not

The AC power cord is not connected or not

Securely connect the power cord.

switch on when

completely connected.

 

POWER is pressed.

 

 

Play does not begin.

The disc is damaged.

Check the disc carefully; replace it if necessary.

 

 

 

 

There is moisture on the laser pick-up.

Wait 20 to 30 minutes after switching the unit on

 

 

before trying to play a disc.

 

 

 

 

The disc has been loaded upside down.

Reload the disc with the label side facing up.

 

 

 

 

The disc is dirty.

Clean the disc.

 

 

 

Play is delayed, or

The disc may be scratched or damaged.

Check the disc carefully; replace it if necessary.

begins at the wrong

 

 

place.

 

 

Recording is not

The disc is finalized.

Load a recordable CD that has not been

possible.

 

finalized yet. For a CD-RW disc, TOC Erase or

 

 

Disc Erase may be needed.

 

 

 

 

A pre-mastered CD is loaded.

Load a recordable CD.

 

 

 

 

The input setting is incorrect.

Set INPUT to the position that reflects the source

 

 

of the input signal.

 

 

 

 

The output level of the source is too low.

Set the output level of the source to MAX.

 

 

 

 

There is not enough blank space left or 99

Load a recordable CD.

 

tracks have already been recorded on the

 

 

disc.

 

 

 

 

 

If the power cord was unplugged or there

If the recording of a CD-RW disc is interrupted,

 

was a power outage during recording, the

try recording again from the beginning. When

 

recorded material may be lost.

the recording of a CD-R disc is interrupted, start

 

 

recording over again with a disc that can be

 

 

recorded on.

 

 

 

 

The disc is dirty or damaged.

Clean or replace the disc.

 

 

 

Cannot play back a

The CD or DVD players are not compatible

Use a CD or DVD player compatible with CD-R

recorded CD-R or CD-

with CD-R or CD-RW discs.

or CD-RW discs.

RW disc on other CD

 

 

The disc is not finalized.

Finalize the disc.

or DVD players.

 

 

 

 

 

Sound “skips.”

The unit and/or the component being

Relocate the unit(s). This is not possible if the

 

recorded is being subjected to vibration or

skipping sound is already on the recording due

 

impact.

to vibrations or impact that occurred during

 

 

recording.

 

 

 

 

The disc is dirty.

Clean the disc.

 

 

 

Sound “hums.”

Improper cable connections.

Securely connect the audio cables. If the

 

 

problem persists, the cables may be defective.

 

 

 

Noise from inside of

The disc may be warped.

Replace the disc.

the unit.

 

 

The remote control

The batteries of the remote control are too

Replace the batteries with new ones.

does not work.

weak.

 

 

 

 

 

Remote control is too far away or is being

Use within 6 meters and 60 degree radius.

 

used at an incorrect angle.

 

 

 

 

 

Direct sunlight or lighting (of an inverter

Change the position of the unit.

 

type of fluorescent lamp, etc.) is striking

 

 

the remote control sensor of the unit.

 

 

 

 

TV functions strangely

Remote control is being used near TV set

Relocate this unit away from the TV or cover the

when the remote

with a remote control sensor.

TV’s remote control sensor.

control is being used.

 

 

 

 

 

E-30