2
Thank you for purchasing an I/O interface card for use with Yamaha digital audio equipment.
Refer to the respective owner’s manual for installation information.
As well as securing the card in place, the fixing screws act as an electrical ground, so
be sure to screw them in tightly.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digi-
tal devices. Compliance with these requirements provides a rea-
sonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio fre-
quencies and, if not installed and used according to the instruc-
tions found in the users manual, may cause interference harmful to
the operation of other electronic devices. Compliance with FCC
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interfer-
ence, which can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
FCC INFORMATION (U.S.A.)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PRECAUTIONS
WARNING
Failure to observe the following warnings may lead to
fatality or serious injury from fire or electric shock.
•Before installing the card, you must refer to the owner’s manual
of the host device or to the Yamaha website (“Guidance on the
use of Mini-YGDAI cards” page) to verify that your host device
supports this card, and to verify the number of cards that can
be installed in combination with other Yamaha or third-party
cards.
Yamaha Pro Audio website: http://www.yamahaproaudio.com/
•Do not attempt to disassemble or modify the card. Do not apply
excessive force to board connectors or other board
components. (Mishandling of board may lead to shock, fire
hazard, or equipment failure.)
•Be sure to disconnect the power cable from the main unit before
installing this card (to eliminate shock hazard).
CAUTION
Failure to observe the following precautions may lead to
personal injury, or may result in damage to equipment or
other property.
• Do not touch the board’s metallic leads (pins) when handling
the card. (Pins are sharp and may cause hand cuts.)
•The card is electrostatic-sensitive. Before handling the card,
you should briefly touch the main unit’s metal casing with your
bare hand so as to drain off any static charge from your body.
*The company names and product names in this Owner's
Manual are the trademarks or registered trademarks of their
respective companies.
* Illustrations herein are for explanatory purposes only, and
may not match actual appearance during operation.
Yamaha assumes no responsibility for data loss, equipment
damage, or injury caused by inappropriate handling or
usage.