151
*9 Exclusive
The following system exclusive messages are recognized.
<GM system ON> FOH, 7EH, 7FH, 09H, 01H, F7H
All parameters except MIDI master Tuning and Dsp setting are
reset to their default values.
Remote Channel setting is cancelled.
This message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
<MIDI Master Volume> F0H, 7FH, 7FH, 04H, 01H, ll, mm, F7H
Allows the volume of all channels to be changed simultane-
ously.
“mm” is used as the MIDI Master Volume value (“ll” is ignored).
The default value for “mm” is 7FH.
<MIDI Master Tuning>
F0H, 43H, 1nH, 27H, 30H, 00H, 00H, mm, ll, cc, F7H
“mm, ll” is used as the MIDI Master Tuning value.
The tuning value is represented as follows:
T=M-128 (28<
=M<
=228), T=-100 (M<28), T=100 (M>228)
T is the actual tuning value in cents.
M is decimal value represented by 1-byte using bits 0..3 of
“mm” as the MSB and bits 0..3 of “ll” as the LSB.
The default values of “mm” and “ll” are 08H and 00H respec-
tively.
n and cc are also recognized.
This value is not reset by a GM System ON or Reset All Con-
trollers message.
This value affects not only MIDI reception part but the entire
system of the PSR-4000.
<XG Native Parameter Change>
F0H, 43H, 1nH, 4CH, aaH, bbH, ccH, ddH........F7H
n: device number (n=0~FH)
aa,bb,cc: address High, Mid, Low
dd: data
A corresponding data size is transmitted when the data size is
2 or 4 parameters.
Note: This product is compatible with the XG format param-
eters listed in the chart, but not with the many other
parameters included in the XG full format.
<XG System On> F0H, 43H, 1nH, 4CH, 00H, 00H, 7E, 00H, F7H
n: device number (n=0~FH)
All parameters other than MIDI master tuning are reset to their
default values.
This message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
<XG System Data Parameter Change>
See Tables 1-1, 1-2.
<Multi Effect1 Data Parameter Change>
See Tables 1-1, 1-3.
<Multi Part Data Parameter Change>
See Tables 1-1, 1-4.
<Drums Setup Data Parameter Change>
See Tables 1-1, 1-5.
<XG Native Bulk Dump>
F0H, 43H, 0nH, 4CH, bl, bh, aaH, bbH, ccH, <Data>, cs, F7H
n: device number (n=0~FH)
bl, bh: byte count (only data portion shown)
aa,bb,cc: address High, Mid, Low (Refer to the accompany-
ing chart)
cs: Checksum (Byte Count + Start Address + Data +
Checksum=0 : calculated binary in first 7 bit)
The data series listed under “Total Size” in the chart is one
bulk dump. Only the header address is used as the bulk
data address.
Since an error can occur when a large amount of bulk data
is received, data series longer than 512 bytes are divided
into groups of less than 512 bytes each, and transmitted
with a time interval of greater than 120 ms between each
group.
Note: This product is compatible with the XG format param-
eters listed in the chart, but not with the many other param-
eters included in the XG full format.
<XG System Data Bulk Dump>
See Tables 1-1, 1-2.
<Multi Effect1 Data Bulk Dump>
See Tables 1-1, 1-3.
<Drums Setup Data Bulk Dump>
See Tables 1-1, 1-5.
<Parameter Request>
F0H, 43H, 3nH, 4CH, aaH, bbH, ccH, F7H
n: device number (n=0~FH)
aa,bb,cc: address High, Mid, Low
Requests are accepted for parameters which can be changed.
Only the header address is interpreted as the parameter re-
quest address for a Data Size of 2 or 4 parameters.
<Dump Request>
F0H, 43H, 2nH, 4CH, aaH, bbH, ccH, F7H
n: device number (n=0~FH)
aa,bb,cc: address High, Mid, Low
The data series listed under “Total Size” in the chart is one bulk
dump. Only the header address is interpreted as the bulk data
address.